DODGE RAM SRT-10 2006 Service Repair Manual

3. If vehicle is aQuad Cab, remove the lower b-pillar
trim panel (1) (Refer to 23 - BODY/INTERIOR/B-
PILLAR LOWER TRIM - REMOVAL).
4. Separate the front door opening seal (6) from the
door opening flange.

REAR DOOR SEAL
1. Remove the lower b-pillar trim panel (1) (Refer to
23 - BODY/INTERIOR/B-PILLAR LOWER TRIM -
REMOVAL).
2. Remove the lower c-pillar trim (1) (Refer to 23 -
BODY/INTERIOR/C-PILLAR TRIM - REMOVAL).

3. Separate the rear door opening seal (5) from the
door opening flange.
INSTALLATION
FRONT DOOR SEAL
1. Position the front door seal (6) to the bottom of the
door opening, with bulb facing outboard, starting
the installation at the center of the lower flange.
Press the seal onto the sill flange and work around
the perimeter of the door opening until fully seated.
Work in one direction, smoothing the seal to avoid
puckers or wrinkles.

2. If vehicle is aStandard Cab, install the lower b-pil-
lar trim (3) (Refer to 23 - BODY/INTERIOR/B-PIL-
LAR LOWER TRIM - INSTALLATION).
3. If vehicle is aQuad Cab, install the lower b-pillar
trim (1) (Refer to 23 - BODY/INTERIOR/B-PILLAR
LOWER TRIM - INSTALLATION).

4. Install the cowl trim panel (1) (Refer to 23 - BODY/
INTERIOR/COWL TRIM - INSTALLATION)
NOTE: When installing a new weatherstrip on the
front door opening, remove the tear strip starting
at the splice and moving around the front of the
door to the back of the opening.
REAR DOOR SEAL
1. Position the rear door seal to the bottom of the
door opening, with bulb facing outboard, starting
the installation at the center of the lower flange.
Press the seal onto the sill flange and work around
the perimeter of the door opening until fully seated.
Work in one direction, smoothing the seal to avoid
puckers or wrinkles.

2. Install the lower c-pillar trim (1) (Refer to 23 -
BODY/INTERIOR/C-PILLAR TRIM -
INSTALLATION).
3. Install the lower b-pillar trim (1) (Refer to 23 -
BODY/INTERIOR/B-PILLAR LOWER TRIM -
INSTALLATION).
NOTE: When installing a new weatherstrip on the
rear door opening, remove the tear strip starting at
the splice and moving around the back of the door
to the front of the opening.

DRIP RAIL WEATHERSTRIP RETAINER
REMOVAL
1. Separate the drip rail weatherstrip (3) from the
weatherstrip retainer (1).
2. Remove the seven screws (2) and remove the
retainer (1).
INSTALLATION
1. Install the weatherstrip retainer (1) and install the
seven screws (2).
2. Position the weatherstrip (3) over the retainer
flange and seat fully.

FRONT DOOR GLASS RUN WEATHERSTRIP
REMOVAL
1. Remove the door glass (Refer to 23 - BODY/
DOOR - FRONT/DOOR GLASS - REMOVAL).
2. Separate the front door glass run weatherstrip (2)
out of the door frame (5) and remove through the
window opening.

INSTALLATION
NOTE: A mixture of soap and water may be used
to aid installation of the weatherstrip into the cor-
ners.
1. Position the front door glass run weatherstrip (2)
into the door (5) through the window opening.
2. Position the weatherstrip into the upper corners
and seat firmly.
3. From back to front, seat the weatherstrip between
the corners and then down the sides firmly.
4. Install the door glass (Refer to 23 - BODY/DOOR -
FRONT/DOOR GLASS - INSTALLATION).

FRONT DOOR OUTER BELT MOLDING
REMOVAL
1. Remove the screw (4) and separate the belt mold-
ing (1) from the door (5) flange from the back to
the front.
INSTALLATION
1. Position the belt molding (1) onto the door (5)
flange and seat fully.
2. Install the screw (4).