power steering DODGE TRUCK 1993 Service Manual PDF

19
- 34
STEERING

• •
4WD vehicles; tighten gear frame reinforcement
bracket to frame bolts/nuts to 223 N-m (165 ft. lbs.)
torque.
(4) Align and install the pitman arm.
(5) Install the washer and retaining nut on the pit­
man shaft. Tighten the nut to 251 N-m (185 ft. lbs.)
torque.
(6) Connect fluid hoses to steering gear, tighten to
28 N-m (21 ft. lbs.). Add fluid, refer to Power Steer­
ing Pump Initial Operation.

POWER STEERING GEAR SPECIFICATIONS

Steering Gear Type ............. Recirculating ball with hydraulic assist.
Ratio Code (Top
of
Gear) BH,NZ
14:1

BF,
XS 13-16:1
Steering Gear Hydraulic Fluid Use Mopar Power Steering Fluid,
or
equivalent.
Steering Gear Lubricants Lubricate pitman shaft
seals,
bearings races,
and
rack piston recirculating balls with
petroleum
jelly.
Lubricate all other parts with power steering fluid. Steering Gear Adjustments:
Wormshaft Bearing Preload Torque 0.45-1.13
Nm
(4
to
10 in-lbs)
Pitman Shaft Overcenter Drag Torque: New Gear
(less than 400 miles/640 km) ......... 0.45-0.90
Nm
(4
to 8
in-lbs)
in
addition
to
wormshaft bearing preload but not to exceed
combined total
of
2
Nm
(18 in-lbs).
Used Gear
(over 400 miles/640 km) 0.5-0.6
Nm
(4 to
5
in-lbs) in addition
to
wormshaft bearing preload but not to exeed
combined total
of
2 N-m (18 in-lbs).

Caution:
Gears must
be
adjusted exactly
as
outlined
in
Steering Gear Adjustments-On Bench. Failure
to

adhere
to
the recommended procedures may result
in gear damage
or
improper steering response.

J9219-36

•

BODY
COMPONENTS
23 - 35
CAB/BODY
INTERIOR COMPONENTS

INDEX

page

Carpets
and
Floor Mats
51
Floor Console
and
Rear Storage Tray
.........
50

Front Seats
38
Headliners
48

Instrument
Panel
35
page

Interior
Trim
Panels
. 42

Rear
Seats
41

Shoulder
Belts/Lap Belt/Buckles
45

Spare
Tire
Carrier
45

INSTRUMENT
PANEL INSTRUMENT CLUSTER BEZEL

REMOVAL
(1) Remove
the
bezel screws.
(2) Remove
the
bezel from
the
instrument panel.

INSTALLATION
(1) Position
the
bezel
on the
instrument panel.
(2) Install
the
bezel screws. Tighten
the
screws
to

2
Nnn (17 in. lbs.)
torque.
INSTRUMENT
PANEL

EDGE
TRIM
4WD
INDICATOR COVER 4WD)
INSTRUMENT CLUSTER
BEZEL
SCREW

Fig.
11nstrument
Cluster
Bezel
Removal/Installation
INSTRUMENT CLUSTER AND/OR
IP

COMPONENT

REMOVAL
(1) Remove
the
instrument cluster bezel screws
(Fig.
1).
Remove
the
bezel from
the
instrument
panel.
(2)
As
applicable, remove
the
instrument cluster
or

other
IP
component screws
(Fig. 2).

(3) Disconnect
the
wire harness connector(s) from
the
IP
cluster
or
component. Refer
to
Group 8—Elec­
trical
for
additional information. (4)
If
applicable, disconnect
the
shift position indi­
cator from
the
steering column
(Fig. 3).

(5) Remove
the IP
cluster
or
component from
the

instrument panel.
INSTALLATION

(1) Position
the IP
cluster
or
component
at the in­

strument panel. Connect
the
wire harness connec­

tors).

(2) Install
the
cluster
or
component
in the
instru­
ment panel
(Fig. 2).

(3)
If
applicable, connect
the
shift position indica­
tor
to the
steering column
(Fig. 3).

(4) Install
the IP
cluster
or
component screws.
Tighten
the
screws
to 2 N#m (17 in. lbs.)
torque. (5) Position
the
bezel
on the
instrument panel.
(6) Install
the
bezel screws. Tighten
the
screws
to

2
Nnn (17 in. lbs.)
torque.
INSTRUMENT
PANEL
LAMP

ACC

SWITCH
BEZEL

HEADLAMP SWITCH
HEADLAMP SWITCH
AND POWER MIRROR
CONTROL
BEZEL
SCREW

INSTRUMENT
J9123351
CLUSTER
J9123-351

Fig.
2
Instrument
Cluster
Removal/Installation
A/T SHIFT POSITION (PRNDL) INDICATOR

REMOVAL
(1) Disconnect
the
shift position (PRNDL) indicator
cable from
the
steering column.
(2) Remove
the
indicator screws from
the
rear
of

the instrument cluster. (3) Remove
the
indicator from
the
instrument clus­
ter.

CLUSTER
AND
GAUGE SERVICE PROCEDURES
. . . 8E-12

CLUSTER
AND
GAUGE TEST PROCEDURES
8E-5

GENERAL INFORMATION
8E-1

MESSAGE
CENTER-DIESEL ENGINE
8E-4

MESSAGE
CENTER-GAS ENGINE
8E-3

SWITCH
AND
PANEL COMPONENT SERVICE
8E-16

INTRODUCTION
lntro.-1
DESIGNATIONS, LABELS/PLATES/DECALS, CODES AND DIMENSIONS/WEIGHTS
Intro.-1

MEASUREMENT
AND
TORQUE SPECIFICATIONS
lntro.-11

LAMPS
8L-1
BULB APPLICATION
8L-11

EXTERIOR LAMPS
8L-1

EXTERIOR LAMPS SERVICE PROCEDURES
8L-3
INTERIOR LAMPS
8L-10

LUBRICATION
AND
MAINTENANCE
0-1
CHASSIS
AND
BODY
0-28
DRIVETRAIN
0-22

ENGINE MAINTENANCE
0-14

GENERAL INFORMATION
0-1

POWER DOOR LOCKS
8P-1
SERVICE
PROCEDURES
8P-2

TEST PROCEDURES
8P-1

POWER MIRRORS
8T-1
SERVICE
PROCEDURES
8T-2

TEST PROCEDURES
8T-1

POWER WINDOWS
8S-1
SERVICE
PROCEDURES
8S-3

TEST PROCEDURES
8S-1

PROPELLER SHAFTS
16-1
GENERAL INFORMATION
16-1
PROPELLER SHAFT REPLACEMENT
16-8

SERVICE
DIAGNOSIS/PROCEDURES
16-3

TORQUE SPECIFICATIONS
16-15
UNIVERSAL
JOINT
REPLACEMENT
16-10

REAR
SUSPENSION
AND
AXLE
3-1
8
3/8 and 9 1/4
AXLE
3-11

GENERAL INFORMATION
3-1

MODEL
60 and 70
AXLES
3-29

POWER-LOK DIFFERENTIAL
3-55

REAR
SUSPENSION—2WD
and 4WD
VEHICLES
.... 3-3

SERVICE
DIAGNOSIS
3-6

SPECIFICATIONS
3-27

SURE-GRIP
DIFFERENTIAL SERVICE
3-28

TORQUE SPECIFICATIONS
3-59

TRAC-LOK DIFFERENTIAL
3-51

REAR
WINDOW DEFOGGER
8N-1
REPAIR PROCEDURES (GRID LINES, TERMINALS,
AND PIGTAILS)
8N-3

SERVICE
PROCEDURES
8N-4

TEST PROCEDURES
8N-1

STEERING
19-1
GENERAL INFORMATION
19-1
POWER STEERING PUMP
19-11
POWER STEERING SYSTEM DIAGNOSIS
19-2

RECIRCULATING BALL POWER STEERING GEAR
. . 19-20

STEERING COLUMN
19-35

STEERING LINKAGE
19-17

TORQUE SPECIFICATIONS
19-40

TRANSMISSION
AND
TRANSFER CASE
21-1

AUTOMATIC TRANSMISSION DIAGNOSIS
AND

TESTING
21-85

AUTOMATIC TRANSMISSION REMOVAL
AND
INSTALLATION
21-142

AUTOMATIC TRANSMISSION—32RH/36RH/37RH/
42RH/46RH
21-73

G360
MANUAL TRANSMISSION
21-46

G360
TRANSMISSION OVERHAUL
21-53

GENERAL INFORMATION-32RH/36RH/37RH
21-73

GENERAL INFORMATION—42RH/46RH
. . . 21-78

IN-VEHICLE SERVICE—32RH/36RH/37RH/ 42RH/46RH
21-130

NP205
TRANSFER CASE
21-342

NP241
TRANSFER CASE
21-350
NV4500
MANUAL TRANSMISSION
21-1

NV4500
TRANSMISSION OVERHAUL
21-6

OVERDRIVE
UNIT
OVERHAUL—42RH/46RH
21-324

TRANSMISSION OVERHAUL—32RH
21-152

TRANSMISSION OVERHAUL—36RH/37RH
21-192
TRANSMISSION OVERHAUL—42RH
21-233

TRANSMISSION OVERHAUL—46RH
21-278

TRANSMISSION/TRANSFER CASE SPECIFICATIONS
21-364

TURN SIGNALS
AND
HAZARD WARNING FLASHER
. . . 8J-1
GENERAL INFORMATION
8J-1
MULTIFUNCTION SWITCH SERVICE PROCEDURES.
. 8J-3

MULTIFUNCTION SWITCH TESTING PROCEDURES.
. 8J-2

VEHICLE
SPEED
CONTROL SYSTEM
8H-1
SERVICE
PROCEDURES
8H-11

TEST PROCEDURES
8H-7

WHEELS
AND
TIRES
22-1
TIRES
22-1

TORQUE SPECIFICATIONS
22-13
VEHICLE VIBRATION
22-11
WHEELS
22-6

WINDSHIELD WIPER
AND
WASHER
SYSTEMS
8K-1
INTERMITTENT WINDSHIELD WIPER FUNCTION
AND
SWITCH TESTING PROCEDURES
8K-6

TWO
SPEED
WINDSHIELD WIPER MOTOR
AND
SWITCH TESTING PROCEDURES
8K-1

WINDSHIELD WASHERS
8K-10

WINDSHIELD WIPER SYSTEM SERVICE
PROCEDURES
8K-7

WIRING DIAGRAMS
8W-1
COMPONENT IDENTIFICATION
8W-9

GENERAL INFORMATION
8W-1

SPLICE
LOCATIONS
8W-29

WIRING DIAGRAMS AD-BODY
8W-37