tow DODGE VIPER 2008 ZB II / 2.G Owners Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 2008, Model line: VIPER, Model: DODGE VIPER 2008 ZB II / 2.GPages: 303, PDF Size: 2.65 MB
Page 23 of 303
2. Remove and replace the battery. Avoid touching the
new battery with your fingers. Skin oils may cause
battery deterioration. If you touch a battery, clean it with
rubbing alcohol.
3. To assemble the transmitter case, snap the two halves
together.
4. Test the transmitter operation.
General Information
This transmitter complies with FCC rules part 15. Opera-
tion is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be
received, including interference that may cause undes-
ired operation.
If your Remote Keyless Entry transmitter ever fails to
operate from a normal distance, check the following:1. Closeness to a radio transmitter, such as a radio station
tower, airport transmitter, and some mobile or CB radios
can affect transmitter operation. To verify if this is the
cause, move the vehicle to another area and test trans-
mitter operation.
2. The transmitter may become ªout of syncº and will no
longer function if operated more than 255 times while out
of range of the vehicle (23 feet or 7 meters) or if operated
while the vehicle battery is dead or disconnected. To
ªsynchronizeº the transmitter, remove the key from the
ignition. Close the hood and all doors. Press both buttons
on the transmitter for about 10 seconds. The horn will
chirp once to acknowledge the signal. Normal transmit-
ter operation should resume.
3. The transmitter battery may be weak or dead. The
expected life of the battery is a minimum of three years.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Page 36 of 303
8. To release the belt, push the red button in the buckle.
The belt will retract automatically to its stowed position.
If necessary, slide the latch plate down the webbing to
allow it to retract fully.
WARNING!
A frayed or torn belt could rip apart in a collision and
leave you with no protection. Inspect the belt system
periodically, checking for cuts, frays, or loose parts.
Damaged parts must be replaced immediately. Do
not disassemble or modify the system. Seat belt
assemblies must be replaced after a collision if they
have been damaged (bent retractor, torn webbing,
etc.).
Lap/Shoulder Belt Untwisting Procedure
Use the following procedure to untwist a twisted lap/
shoulder belt.
1. Position the latch plate as close as possible to the
anchor point.
2. At about 6 to 12 inches (15 to 30 cm) above the latch
plate, grasp and twist the belt webbing 180É to create a
fold that begins immediately above the latch plate.
3. Slide the latch plate upward over the folded webbing.
The folded webbing must enter the slot at the top of the
latch plate.
4. Continue to slide the latch plate up until it clears the
folded webbing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35
2
Page 43 of 303
5. Never allow a child to place the shoulder belt behind
them or under the arm.
6. Never allow a child to lean forward toward the
instrument panel as a passenger airbag deployment
could cause severe injury or death to a child in this
position.
7. For a child from 1 to 12 years old: Move the passenger
seat as far back as possible. For a child from 20 to 60
pounds (9 kg to 27 kg): Secure them in the appropriate
child safety seat or booster seat. If too large for a booster
seat, the child should wear the lap/shoulder belt prop-
erly.
8. Read the instructions provided with your child re-
straint to make sure that you are using it properly.
9. Read the instructions provided with your child safety
seat or booster seat to make sure that you are using it
properly.10. All occupants should wear their lap and shoulder
belts properly.
11. Position the driver seat and passenger seat as far
away from the instrument panel as practical to allow the
airbags room to inflate. Note that the power adjustable
pedals allow for more driver's seat adjustment options.
Refer to ªAdjustable Pedalsº in Section 3 of this manual
for details.
Airbag System Components
The airbag system consists of the following:
²Occupant Restraint Controller (ORC)
²Airbag Warning Light
²Driver Airbag
²Passenger Airbag
²Passenger Airbag Off Light
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Page 45 of 303
The ORC turns on the Airbag warning light
and Passenger Airbag Disable (PAD) indica-
tor light for 6 to 8 seconds as a self-check
when the ignition is first turned on. After the
self-check, the Airbag warning light will turn off and
the PAD indicator light will function normally (Refer to
ªPassenger Airbag Disable (PAD) Indicator Lightº in
this section). If the ORC detects a malfunction in any
part of the system, it turns on the Airbag warning light
either momentarily or continuously. A single chime will
sound if the light comes on again after initial start up.
WARNING!
Ignoring the Airbag Warning Light in your instrument
panel could mean you won't have the airbags to protect
you in a collision. If the light does not come on, stays
on after you start the vehicle, or if it comes on as you
drive, have the airbag system checked right away.
²TheDriver Airbag/Inflator Unitis mounted in the
steering wheel. ThePassenger Airbag/Inflator Unitis
mounted underneath a cover in the passenger side of
the instrument panel. When the ORC detects a colli-
sion requiring the airbags, it signals the inflator units.
A large quantity of non-toxic gas is generated to inflate
the airbags. Different airbag inflation rates may be
possible based on collision severity and occupant size.
The steering wheel hub trim cover and the upper right
side of the instrument panel separate and then fold out
of the way, as the bags inflate to their full size. The
bags inflate fully in about 50±70 milliseconds. This is
about half of the time it takes to blink your eyes. The
bags then deflate quickly while helping to restrain the
driver and passenger. The airbag gas is vented toward
the instrument panel through vent holes in the airbag
material. In this way, the airbags do not interfere with
your control of the vehicle.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Page 65 of 303
3. Depress the button located at the top of the latch and
then pull the latch handle downward and rearward.
4. Disengage the latch hook from the windshield receiver
rod and then pull the latch all the way back to the detent
stow position.5. Pull the convertible top away from the windshield
header.
6. Raise both sun visors if so desired.
7. Open the trunk.
8. Pull the convertible top all the way back into the
storage well behind the seats.
9. Push the leading edge of the top downward to engage
the downstack latch.
10. Close the trunk.
To Raise the Top:
1. Lower the window in each door at least one inch.
2. Lower both sun visors.
3. Open the trunk.Unlatching Convertible Top
64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 67 of 303
7. From inside the vehicle, grasp the handles and pull the
convertible top toward the windshield header. Then,
push the latch handle forward so that the latch hook
engages the windshield receiver rod.8. Ensure that the outboard locating pins are in their
respective receiving holes in the windshield header and
then push the latch handle forward all the way to close
the latch.
Aligning Convertible TopEngaging Convertible Top
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 68 of 303
NOTE:Until the convertible top system has had ad-
equate time to break-in, it may take a greater effort to
engage the latch hook and close the latch. However,
several weeks of normal convertible top usage will
reduce these efforts.
9. Raise both sun visors if so desired.
10. Adjust the windows as desired.
Convertible Top Boot Cover Installation ± If
Equipped
1. Open the trunk.
2. Lower the convertible top. Verify that the latch handle
is placed in the detent stow position.3. Lay the unfolded boot cover across the convertible
top.
Unfolded Boot Cover
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67
3
Page 76 of 303
MIRRORS
Inside Day/Night Mirror
Adjust the mirror to center on the view through the rear
window. A pivot system allows for horizontal and verti-
cal mirror adjustment.Annoying headlight glare can be reduced by moving the
small control under the mirror to the night position
(toward rear of vehicle). The mirror should be adjusted
while set in the day position (toward windshield).
Outside Mirrors
To receive maximum benefit, adjust the outside mirrors
to center on the adjacent lane of traffic and a slight
overlap of the view obtained from the inside mirror.
NOTE:The passenger side convex outside mirror will
give a much wider view to the rear, and especially of the
lane next to your vehicle.
Adjusting Rearview Mirror
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75
3
Page 84 of 303
You can also signal a lane change by moving the lever
partially upward or downward without moving beyond
the detent. The turn signals will continue to operate until
you release the lever.
If either light has a very fast flash rate, check for a
defective outside light bulb. If an indicator fails to lightwhen the lever is moved, it would suggest that the fuse
or indicator is defective or there may be a circuit failure.
Highbeam/Lowbeam Select Switch
Pull the Multi-Function Lever toward you to switch the
headlights to HIGH beam. Pull the lever a second time to
switch the headlights back to LOW beam.
Turn Signal Control
Headlight Beam Control
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83
3
Page 85 of 303
Flash to Pass
You can signal another vehicle with your headlights by
lightly pulling the Multi-Function Lever toward you.
This will cause the headlights to turn on at high beam
and remain on until the lever is released.
Interior Lights
The interior lights will turn on whenever a door is
opened or the liftgate is opened (Coupe models) and the
dimmer switch is not in the defeat position.
The interior lights will turn on, remain on for about 30
seconds, and then fade to off if any of the following
occur:
²A door is opened using the outside door handle and
then closed.
²A door is unlocked using the remote keyless entry
transmitter.
²A door is unlocked using the outside driver's door key
cylinder.
The interior lights will turn on and remain on for about 4
seconds and then fade to off if a door is opened using the
inside door handle.
Courtesy/Reading Lights
Two courtesy/reading lights are located in the bottom of
the rearview mirror. You can turn these lights on and off
from the switches in the bottom of the mirror or from the
dimmer control in the Multi-Function Lever. These lights
are also controlled automatically by the illuminated entry
system.
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE