Tyre FIAT 500 2018 Owner handbook (in English)

KNOWING YOUR CAR
22
SIDE LIGHTS AND DIPPED BEAM HEADLIGHTS - FOLLOW ME HOME
Side lights and dipped beam headlights
The warning light switches on when the side lights or dipped headlights are turned on.
Follow Me Home
The warning light comes on, on some versions along with a dedicated message on the display, when the
“Follow me home” device is used.
33
iTPMS SYSTEM (for versions/markets, where provided)
Low tyre pressure
The warning light switches on constantly to indicate that the pressure of one or more tyres is lower than the recommended
value or to indicate a slow loss of pressure.
In this way the iTPMS warns the driver that one or more tyres may be flat and probably punctured. In this case it is advisable
to restore the correct pressure value.
Once the normal operating conditions of the vehicle are restored, carry out the Tyre reset procedure.
IMPORTANT Do not continue driving with one or more flat tyres as handling may be compromised.
Stop the vehicle, avoiding sharp braking and steering.
iTPMS failure/iTPMS temporarily deactivated
The warning light flashes for about 75 seconds and then stays on constantly (together with a message on the display) to
indicate that the system is temporarily deactivated or faulty.
The system goes back to normal operation when the operating conditions allow it. If this is not the case, carry out the Reset
procedure after restoring the normal operating conditions.
If the malfunction warning persists, contact a Fiat Dealership as soon as possible.
n
FOG LIGHTS
The warning light comes on when the fog lights are turned on.
LEFT-HAND DIRECTION INDICATOR
The warning light turns on when the direction indicator control lever is moved downwards or, together with the right
indicator, when the hazard warning light button is pressed.
55
FR

27
HEADLIGHT
ALIGNMENT
With the ignition key at MAR and
dipped beam headlights on, press the
+ button to adjust the headlights
upwards and the – button to adjust the
headlights downwards.
TYRE RESET (ITPMS
RESET)
(for versions/markets, where provided)
With this function it is possible to reset
the iTPMS (see paragraph “iTPMS”). To
carry out the Reset procedure proceed
as follows:
❒ briefly press the MENU
N; the
display will show “Reset”;
❒ press button + or – to select (“Yes”
or “No”); a dedicated reset
confirmation message will appear;
❒ briefly press the MENU
N; the
display will show “Confirm”;
THE KEYS1)
1) 1)
CODE CARD
(for versions/markets, where provided)
The car is delivered with two copies of
the ignition key and with the CODE
card fig. 7 which bears the following:
A: the electronic code;
B: the mechanical key code to be given
to the Fiat Dealership when ordering
duplicate keys.
You should have the electronic code
with you at all times.
IMPORTANT All the keys and the
CODE card must be handed over to
the new owner when selling the car.
MECHANICAL KEY
The metal insert A-fig. 8 operates:
❒ the ignition switch;
❒ the door locks and the tailgate (for
versions/markets, where provided);
❒ the locking/unlocking of the fuel
cap.
KEY WITH REMOTE
CONTROL
(for versions/markets, where provided)
The metal insert A-fig. 9 operates:
❒ the ignition switch;
❒ the door locks;
❒ the locking/unlocking of the fuel
cap.
7DVDF0S0103c
8DVDF0S0104c

49
ESC (Electronic
Stability Control)
system 15)
This is an electronic system that
controls vehicle stability in the event of
tyre grip loss, helping maintain
directional control.
The system is capable of recognising
potentially dangerous situations in
terms of the stability and intervenes
automatically on the brakes in a
differentiated manner for the four
wheels in order to provide a stabilising
torque.
The ESC system also includes the
following subsystems:
❒ HH (Hill Holder): it activates
automatically when starting with car
stationary, on a road with a
gradient higher than 5%.
❒ ASR (AntiSpin Regulation):
The system automatically operates
in the event of slipping, loss of grip
on wet roads (aquaplaning) and
acceleration on slippery, snowy or
icy roads, etc. on one or both drive
wheels.
The ASR comes on automatically
whenever the engine is started. When
driving it is possible to deactivate and
then reactivate the ASR system by
pressing the button A fig. 50: the
system activation is signalled by the
LED on the same button switching on
and, on some versions, by a message
on the display.
❒ HBA (Hydraulic Brake Assist): it
operates automatically and
improves the braking capacity of the
vehicle during emergency braking.
50DVDF0S0151c
SYSTEM INTERVENTION
It is signalled by the blinking of the
warning light
Ion the instrument
panel, to inform the driver that the car
is in critical stability and grip
conditions.
SYSTEM ACTIVATION
The ESC system switches on
automatically when the engine is
started and cannot be switched off.

KNOWING YOUR CAR
50
iTPMS System
(indirect Tyre
Pressure
Monitoring System)
(for versions/markets, where provided)
48)
RESET PROCEDURE
The iTPMS needs an initial “self-
learning” phase (with length depending
on the driving style and road
conditions: optimal conditions being
driving on a straight road at 80 km/h
for at least 20 minutes) which starts
when the Reset procedure is carried
out.
The Reset procedure must be carried
out:
❒ each time tyre pressure is
modified;
❒ when even only one tyre is
changed;
❒ when tyres are rotated/inverted;
❒ when the space-saver wheel is
fitted.
In a few situations such as sporty
driving, particular conditions of the
road surface (e.g. icy, snowy,
unsurfaced roads...) the signalling may
be delayed or partial in detecting the
contemporary deflation of more than
one tyre.
Under special conditions (e.g. vehicle
loaded asymmetrically on one side,
towing a trailer, damaged or worn tyre,
fitting the space-saver wheel, use of
the “Fix&Go” quick tyre repair kit,
fitting snow chains, fitting different
tyres on the axles) the system may
give false indications or be temporarily
deactivated.
If the system is temporarily
deactivated, the warning light
nflashes for about 75 seconds and then
is continuously on; at the same time,
the display shows a dedicated
message.
This indication is displayed also after
the engine has been switched off and
then on again if the correct operating
conditions are not restored. Before carrying out the “Reset”
procedure, inflate the tyres to the
rated pressure values specified in the
inflation pressure table (see “Wheels”
paragraph in the “Technical
specifications” chapter).
If the Reset procedure is not carried
out, in all above cases, the
nwarning light may give false indications
on one or more tyres.
To carry out the Reset procedure, with
the vehicle stopped and the ignition
key at MAR, use the setup menu (see
the description of the “Display”
paragraph). At the end of the Reset
procedure the display will show the
“Reset saved” message, indicating
that the self-learning has been started.
If the iTPMS self-learning is not
correctly executed, the message is not
displayed.
OPERATING
CONDITIONS
The system is active for speeds above
15 km/h.

131
“Fix&Go” KIT
33) 31)
DESCRIPTION
The Fix&Go quick tyre repair kit fig. 105
is located in the luggage compartment,
inside a dedicated container, and
consists of:
❒ one cartridge 1 containing sealant
and fitted with: transparent tube for
injecting the sealant 4 and sticker 3
with the wording “Max 80 km/h” to
be placed in a clearly visible position
(e.g. on the dashboard) after
repairing the tyre;
❒ one compressor 2;
❒ one leaflet containing instructions
for using the kit;
❒ a pair of gloves located in the hose
compartment of the cartridge 4.
REPAIR PROCEDURE
Proceed as follows:
❒ stop the car in a position that is not
dangerous for oncoming traffic
where you can carry out the
procedure safely. The ground must
be flat and sufficiently compact;
❒ stop the engine, engage the hazard
warning lights and the parking
brake;
❒ wear the reflective safety jacket
before getting out of the car (in any
case, comply with the laws in force
in the country you are driving in);
105DVDF0S0230
❒ insert the cartridge 1 containing the
sealant into the dedicated
compartment on the compressor 2
and press it down hard fig. 105.
Remove the adhesive speed label 3
and apply it in a clearly visible
position fig. 106;
❒ wear the gloves;
❒ remove the valve cap from the
punctured tyre and screw the
transparent sealant hose 4 fig. 105
onto the valve. If a 250 ml cartridge
is present the housing of the
transparent tube is provided with
removable ring to facilitate
extraction. Make sure that the
ON-OFF button 5 fig. 107 is in the
off position (button not pressed);
106DVDF0S0234

IN AN EMERGENCY
132
❒ insert the electrical connector
6 fig. 108 into the 12V socket on
the vehicle and start the engine;
❒ turn on the compressor by pressing
the ON-OFF button 5 fig. 107.
When the pressure shown in the
"Wheels" paragraph in the
“Technical data” chapter or on the
specific label appears on the
pressure gauge 7, stop the
compressor by pressing the
ON-OFF button 5 again;
107DVDF0S0232
❒ disconnect the cartridge 1 from the
compressor by pressing the
release button 8 and lifting the
cartridge 1 up fig. 109.
108DVDF0S0231
109DVDF0S0233
If the pressure gauge 7 fig. 107 shows
a pressure less than 1.8 bar / 26 psi
15 minutes after turning on the
compressor, switch off the
compressor, disconnect the sealant
hose 4 from the tyre valve and remove
the cartridge 1 from the compressor
fig. 105.
Move the vehicle about 10m to
distribute the sealant; stop the vehicle
safely, engage the handbrake and
restore the pressure using the black
inflation hose 9 fig. 110 until the
required pressure is reached. If also in
this case, the pressure is lower than
1.8 bar / 26 psi 15 minutes after
turning on, do not resume driving but
contact a Fiat Dealership.
110DVDF0S0235

133
After driving for about 8 km / 5 miles,
position the car in a safe and suitable
area and engage the handbrake.
Take the compressor and restore the
pressure using the black inflation hose
9 fig. 110.
If the pressure shown is higher than
1.8 bar / 26 psi, restore the pressure
and drive safely to a Fiat Dealership as
soon as possible.
If, however, the pressure is lower than
1.8 bar / 26 psi, do not resume driving
but contact a Fiat Dealership.INFLATION PROCEDURE
Proceed as follows:
❒ stop the vehicle safely, as shown
above, and operate the handbrake;
❒ take out the black inflation hose 9
fig. 103 and screw it firmly onto the
tyre valve. Follow the instructions
given in fig. 108 and fig. 110.
Press the air release button
10 fig. 107 to adjust any tyre
overpressure.
CARTRIDGE
REPLACEMENT
Proceed as follows:
❒ only use original Fix&Go cartridges,
which can be purchased from the
Fiat Dealership.
❒ press the release button 8 fig. 109
and lift it to remove the cartridge 1.

147
SERVICING AND CARE
SCHEDULED SERVICING
Correct servicing is crucial for
guaranteeing a long life for the vehicle
under the best conditions.
For this reason, Fiat has planned a
series of checks and services at fixed
distance intervals and, for
versions/markets, where provided, at
fixed time intervals, as described in the
Scheduled Servicing Plan.
Regardless of the above, it is always
necessary to carefully follow the
instructions in the Scheduled Servicing
Plan (e.g. periodically check level of
liquids, tyre pressure, etc.).
Scheduled Servicing is offered by all
Fiat Dealerships according to fixed
time or kilometres/miles intervals.
If, during each operation, in addition to
the ones scheduled, the need arises
for further replacements or repairs,
these may be carried out with the
owner’s explicit agreement only. If your
vehicle is used frequently for towing,
the interval between one service
operation and the next should be
reduced. IMPORTANT NOTES
Scheduled Servicing interventions are
set out by the Manufacturer. Failure to
have them carried out may invalidate
the warranty.
We advise you to inform a Fiat
Dealership of any small operating
irregularities without waiting for the
next service.

Years4321SERVICING AND CARE
148
5109876
SCHEDULED SERVICING PLAN39) 21)
Thousands of kilometres7515013512010590
PETROL/LPG VERSIONS
IMPORTANT: When you have carried out the last intervention in the table, continue with the scheduled servicing,
maintaining the frequency indicated in the plan by marking each operation with a dot or dedicated note.
Warning: simply restarting maintenance from the beginning of the plan may cause the allowed interval to be exceeded for
some operations!
60453015
Thousands of miles4590817263543627189





 
 
 
 Check tyre condition/wear and adjust pressure, if necessary;
check the condition/expiry date of the “Fix&Go Automatic” repair kit (for versions/markets, where provided)
Check operation of lighting system (headlights, direction indicators,
hazard warning lights, boot, passenger compartment,
glove compartment, instrument panel warning lights, etc.)
Check and, if necessary, top up fluid levels (1)
Check exhaust emissions/smokiness
Use the diagnosis socket to check supply/engine management
systems, emissions and engine oil decay
(for versions/markets, where provided)
Visually inspect the conditions of: bodywork, underbody protection,
pipes and tubes (exhaust - fuel - brakes), rubber parts
(boots, sleeves, bushes, etc.)
Check windscreen/rear window wiper blade
position/wear (for markets/versions, where provided)
Check operation of windscreen washer system and adjust jets
if necessary
Check cleanliness of bonnet and luggage compartment locks,
cleanliness and lubrication of linkage
(1) Topping up must be carried out with the fluids indicated in this Use and Maintenance Booklet and only after checking that the system is
undamaged

151
43215109876
100200180160140120
DIESEL VERSIONS
IMPORTANT: When you have carried out the last intervention in the table, continue with the scheduled servicing, maintaining
the frequency indicated in the plan by marking each operation with a dot or dedicated note.
Warning: simply restarting maintenance from the beginning of the plan may cause the allowed interval to be exceeded for
some operations!
80604020
Check tyre condition/wear and adjust pressure, if necessary;
check the condition/expiry date of the “Fix&Go Automatic” repair kit
(for versions/markets, where provided)
Check operation of lighting system (headlights, direction indicators,
hazard warning lights, boot, passenger compartment,
glove compartment, instrument panel warning lights, etc.)
Check and, if necessary, top up fluid levels (1)
Check exhaust emissions/smokiness
Use the diagnosis socket to check supply/engine management
systems, emissions and engine oil decay (for versions/markets,
where provided)
Visually inspect the conditions of: bodywork, underbody protection,
pipes and tubes (exhaust - fuel - brakes), rubber parts
(boots, sleeves, bushes, etc.)
Check windscreen/rear window wiper blade position/wear
(for markets/versions, where provided)
Check operation of windscreen washer system and adjust jets
if necessary
Check cleanliness of bonnet and luggage compartment locks,
cleanliness and lubrication of linkage
(1) Topping up must be carried out with the fluids indicated in this Use and Maintenance Booklet and only after checking that the system is
undamaged




 
 
 

Thousands of kilometres
Thousands of miles6012010896847248362412
Years