instrument panel FIAT 500 2018 Owner handbook (in English)

7
INSTRUMENT PANEL
KNOWING YOUR CAR
1a
A direction indicator stalk – B audio controls on steering wheel – C instrument panel – D headlight alignment corrector – E audio controls on
steering wheel – F windscreen wiper/washer and rear window wiper/washer stalk – G dualdrive power steering (CITY function)
H display: audio system/Uconnect™ – I central air diffusers – L fog lights/rear fog lights – M passenger airbag – N side air diffusers
O glove box – P emergency lights and switch – Q climate control system controls – R right electric window – S gear lever
T left electric window – U ASR-OFF button– V ignition switch – Z driver airbag – X steering wheel adjustment lever – W Cruise Control/Speed
Limiter lever
DVDF0S0219c

KNOWING YOUR CAR
8
DASHBOARD WITH SPORT STEERING WHEEL
1b
A direction indicator stalk – B audio controls on steering wheel – C instrument panel – D headlight alignment corrector – E audio controls on
steering wheel – F windscreen wiper/washer and rear window wiper/washer stalk – G dualdrive power steering (CITY function)
H display: audio system/Uconnect™ – I central air diffusers – L fog lights/rear fog lights – M passenger airbag – N side air diffusers
O glove box – P emergency lights and switch – Q climate control system controls – R right electric window – S gear lever
T left electric window – U ASR-OFF button– V ignition switch – Z driver airbag – X steering wheel adjustment lever – W Cruise Control/Speed
Limiter lever
DVDF0S0220c

9
INSTRUMENT PANEL
VERSIONS WITH MULTIFUNCTION DISPLAY
A speedometer
B rev counter (diesel version shave
a full-scale of 6
RPMX1000)
C display with digital fuel level and engine
coolant temperature indicators
Warning lights
mtEare only
provided on diesel versions.
Warning light supplied on Dualogic
versions only.
DVDF0S0222c2

11
WARNING LIGHTS AND MESSAGES 31)
IMPORTANT NOTES
IMPORTANT Warning lights are accompanied by a specific message and/or sound when
applicable. These indications are indicative and precautionary and as such must not be considered as exhaustive and/or
alternative to the information contained in the Owner Handbook, which you are advised to read carefully in all cases.
Always refer to the information in this section in the event of a failure indication.
IMPORTANT Failure indications displayed are divided into two categories: very serious and less serious failures.
Serious faults are indicated by a repeated and prolonged warning “cycle”.
Less serious faults are indicated by a warning “cycle” with a shorter duration. The display cycle of both categories can be
interrupted by pressing the MENU button. The instrument panel warning light will stay on until the cause of the
malfunction is eliminated.
–
LOW BRAKE FLUID/HANDBRAKE – ENGAGED
The warning light switches on when the ignition key is turned to MAR, but it should switch off after a few seconds.
Low brake fluid level
The warning light turns on when the level of the brake fluid in the reservoir falls below the minimum level, possibly due to a
leak in the circuit. On some versions the display shows the dedicated message.
Handbrake engaged
The warning light switches on when the handbrake is engaged.
On certain versions, if the car is moving the acoustic warning will also sound.
IMPORTANT If the warning light turns on when travelling, make sure that the handbrake is not engaged.
AIRBAG FAULT
The warning light switches on when the ignition key is turned to MAR, but it should switch off after a few seconds.
The warning light stays on constantly if there is a fault in the airbag system.
On some versions the display shows the associated message.
xx
¬¬

KNOWING YOUR CAR
12
HOT ENGINE COOLANT
The warning light switches on when the ignition key is turned to MAR, but it should switch off after a few seconds.
The warning light or symbol on the display lights up when the engine is overheated, on some versions, together with a
dedicated message on the display.
❒ In normal driving conditions: stop the car, switch off the engine and check that the fluid level in the reservoir is not
below the MIN mark. In this case, wait for the engine to cool down, then slowly and carefully open the cap, top up with
coolant and check that the level is between the MIN and MAX marks on the reservoir itself. Also check visually for any
fluid leaks. Should the warning light turn on again at the next start-up, contact a Fiat Dealership.
❒ if the vehicle is used under demanding conditions (e.g. towing trailers uphill or fully loaded): slow down and, if the
light stays on, stop the car. Stop for two or three minutes with the engine running and slightly accelerated to facilitate
better coolant circulation, then turn the engine off. Check that the coolant level is correct as described above.
IMPORTANT Over demanding routes, it is advisable to keep the engine running and slightly accelerated for a few minutes
before turning it off.
On certain versions the dedicated message is displayed.uu
{{
“DUALDRIVE” ELECTRIC POWER STEERING FAULT
When the key is turned to MAR, the warning light switches on but it should switch off after a few seconds.
If the warning light stays on, on some versions along with a dedicated message on the display, you may not have steering
assistance and the effort required to operate the steering wheel could be notably increased; steering is, however, possible.
In this case, contact a Fiat Dealership.
If the warning light switches on while driving (on some versions, together with a dedicated message on the display) you may
not have steering assistance. Although it will still be possible to steer the vehicle, the effort needed to operate the steering
wheel could be increased: contact a Fiat Dealership as soon as possible.
IMPORTANT In some circumstances, factors independent of the electric power steering could cause the warning light on
the instrument panel to switch on. In this case, stop the car immediately (should it be in motion), stop the engine for about
20 seconds and then restart the engine. If the warning light stays on, contact a Fiat Dealership.
IMPORTANT After the battery is disconnected, the steering must be initialised. The warning light switches on to indicate
this. To carry out this procedure, simply turn the steering wheel all the way from one end to the other or drive in a straight
line for about a hundred metres.

19
ESC SYSTEM (for versions/markets, where required)
The warning light switches on when the ignition key is turned to MAR, but it should switch off after a few seconds.
ESC system activation
Flashing of the warning light while driving indicates the intervention of the ESC system.
ESC system failure
If the warning light does not go off or stays on together with the LED on the ASR OFF button while driving.
The display will show a dedicated message.
Contact a Fiat Dealership.
Hill Holder failure
This warning light switches on, on some versions together with a dedicated message on the display, in the event of a Hill
Holder system fault.
In this case, contact a Fiat Dealership as soon as possible. Parking sensor fault
The warning light turns on and the dedicated message is shown on the display when a parking sensor fault is detected.
Start&Stop system fault (versions with multifunction display)
A fault of the system is indicated by the warning light switching on. A dedicated message will appears on the instrument
panel.
Airbag warning light fault (for versions/markets, where provided)
The warning light will blink when a fault of the
¬warning light is detected.
ESCESC
BRAKE PAD WEAR
The warning light switches on, together with a dedicated message on the display, if the front or rear brake pads (on
version/markets, where provided) are worn.
In this case have them replaced as soon as possible.
dd
POSSIBLE ICE ON ROAD
The symbol is shown on the display (on some versions together with a dedicated message) when the outside temperature
is equal to or below 3°C.
èè
(versions with
multifunction
display)
(versions with
multifunction
display)

KNOWING YOUR CAR
26
DEACTIVATING FRONT
PASSENGER AIRBAG
AND SIDE BAG
(for versions/markets, where provided)
This function allows the passenger side
airbag to be activated/deactivated.
Proceed as follows:
❒ briefly press MENU
Nbutton and,
after displaying the message
(Passenger bag: Off)
(to deactivate) or the message
(Passenger Bag: On) (to activate) by
pressing the + and – buttons, press
the MENU
Nbutton again;
❒ the confirmation request message is
displayed;
❒ press buttons + or – to select (Yes)
(to confirm activation/deactivation)
or (No) (to abort);
❒ briefly press MENU
Nto confirm
setting and go back to the menu
screen or hold the button down to
go back to the standard screen
without saving.With Passenger’s protection not
active, the LED “on the instrument
panel lights up fixed.
SERVICE
(SCHEDULED
SERVICING)
This function allows you to display the
information about km/mileage intervals
or, for versions/markets, where
provided, time intervals for car
servicing.
To consult the information, proceed as
follows:
– briefly press the MENU
Nbutton:
the display shows when servicing is
due in kilometres/miles or days (where
provided) according to the previous
setting (see paragraph “Units of
measurement”);
– briefly press the MENU
Nbutton to
go back to the menu screen or press
the button for long to go back to the
standard screen.
IMPORTANT The “Scheduled Servicing
Plan” includes car maintenance at fixed
intervals (refer to the “Maintenance and
care” chapter).This is displayed automatically, with
ignition key at MAR-ON, 2000 km (or
equivalent value in miles) before
servicing or, where provided, 30 days
before servicing. It is also displayed
each time the key is turned to MAR-
ON or, for versions/markets, where
provided, every 200 km (or equivalent
value in miles). Below this threshold
servicing indications are more frequent.
The display will be in km or miles
according to the unit of measurement
set. When the following scheduled
servicing is approaching, the word
“Service” will appear on the display,
followed by the number of
kilometres/miles or days (where
provided) left, when the key is turned to
MAR. Go to a Fiat Dealership, where the
“Scheduled Servicing Plan” operations
will be performed and the message will
be reset.
When the service interval is reached
and for about 1000 km/600 mi or 30
days, a service due message is
displayed.

KNOWING YOUR CAR
28
FIAT CODE
SYSTEM
The Fiat Code system is an electrical
engine immobiliser system which
increases protection against attempted
car theft. It is automatically activated
when the ignition key is removed.
Each time the vehicle is started by
turning the ignition key to MAR, the Fiat
CODE system control unit sends a
recognition code to the engine control
module to deactivate the immobiliser.
If, during ignition, the code is not
correctly recognized, a warning light
is lit on the instrument panel .
In this case, turn the key to STOP and
then to MAR-ON; if it is still locked, try
again with the other keys that come
with the car.
Contact a Fiat Dealership if you still
cannot start the engine.
NOTE Each key has its own code
which must be stored by the control
unit of the system.
Contact a Fiat Dealership to have new
keys (up to 8) stored with a code.
IGNITION
DEVICE
The key can be turned to three
different positions fig. 10:
❒ STOP: engine stopped, key can be
removed, steering column locked.
Some electrical devices (e.g. audio
system, central door locking
system, etc.) can operate;
❒ MAR: driving position.
All electrical devices are enabled;
❒ AVV: engine starting.
The ignition device is fitted with a
safety system that requires the ignition
key to be turned back to STOP if the
engine does not start, before the
starting operation can be repeated.
10DVDF0S011c
Pressing button B opens/closes the
metal insert.
Briefly press button
Ë: for unlocking of
doors and tailgate, timed switching-on
of interior lights and double flashing of
direction indicators (for
versions/markets, where provided).
Briefly press button
Á: for remote
locking of doors and tailgate,
switching-off of the internal ceiling
lights and single flashing of direction
indicators (for versions/markets, where
provided).
Press the Rbutton: remote opening
of the luggage compartment and
double flashing of the direction
indicators.
9DVDF0S0105c

35
With the selector switch in the AUTO
position, the side lights and dipped beam
headlights are controlled by the dusk
sensor.
MAIN BEAM
HEADLIGHTS
❒ With the ring in the 2position,
push the stalk forwards towards the
dashboard. The
1warning light on
the instrument panel will light.
❒ For vehicles with the AUTO
function: with the ring in the AUTO
position and the dipped beam
headlights on, push the stalk
forwards toward the dashboard.
❒ They are deactivated by pulling the
stalk towards the steering wheel.
Flashing
❒ You can flash the beams pulling the
stalk toward the steering wheel
(unstable position).
PARKING LIGHTS
These lights can be turned on with the
starter switch in the STOP position or
with the key removed, by moving the
left stalk ring first to the position (or
the AUTO position if the vehicle does
not have a dusk sensor) and then to
position
2.The warning light
3lights on the
instrument panel. Repeat the same
operation to switch them off.
DIRECTION INDICATORS
Bring the stalk to the (stable) position:
❒ up a: activates the right direction
indicator;
❒ down b: activates the left direction
indicator.
LANE CHANGE
FUNCTION
❒ Move the lever upwards or
downwards (unstable position) for
less than half a second and the
direction indicator will flash 3 times
to signal a lane change, then
immediately switch off
automatically.
FOLLOW ME HOME
This function allows the space
surrounding the car to be lit up for the
set period of time.
Activation
The “Follow Me Home” device is
activated by pulling the stalk fig. 25
towards the steering wheel, in addition
to the stroke end click.
EXTERNAL LIGHTS
DAYTIME RUNNING
LIGHTS
7)
❒ For vehicles with the AUTO
function: with the key in the MAR
position and the ring turned to the
O position, the daytime running
lights switch on automatically.
❒
For vehicles with the AUTO function:
the daytime running lights are turned
on automatically by the dusk sensor
when the ring is in the AUTO position.
DIPPED HEADLIGHTS/
SIDE LIGHTS
❒ With key at MAR, turn the ring nut to
2. The warning light
3on the
instrument panel will come on. When
the dipped beam headlights are on,
the daytime running lights switch off.
24
1
2
DVDF0S008c

KNOWING YOUR CAR
36
It is possible to enable this function
within 2 minutes after turning off the
engine. This function allows turning on
lights and low beams. It is possible to
set the headlights turning on time by
pulling the left lever towards the
steering wheel (unstable position) one
or more times. In this case it is
possible to choose between 0, 30, 60,
90 up to a maximum of 210 seconds.
Each time the stalk is operated, the
warning light
3on the instrument
panel switches on. The display shows
a message and the time set for the
function.
The
3warning light comes on when
the stalk is first moved and stays on
until the function is automatically
deactivated.
Deactivation
This function is deactivated turning on
again the headlights, sidelights or
pulling the left lever towards the
steering wheel (unstable position) for
more than 2 seconds, or switching the
starter to MAR.
AUTO FUNCTION
(Dusk sensor)
(for versions/markets, where provided)
This is an infrared LED sensor that works
in conjunction with the rain sensor. It is
located on the windscreen (fig. 25) and is
able to detect variations in outside
lighting based on the light sensitivity set
in the display Menu or the Uconnect™
5" or 7" HD system (where provided).
The higher the sensitivity, the lower the
amount of external light needed to
automatically switch the external lights
on.
25DVDF0S0215c
Function activation
Turn the left stalk ring A fig. 26 to the
AUTOposition.
IMPORTANT The function can only be
activated with the ignition device in the
MAR position.
Function deactivation
To deactivate the function, turn the left
stalk ring A to position 2.
26DVDF0S0216c