heat FIAT PANDA 2009 169 / 2.G User Guide

F0Z0163m
fig. 92
It is absolutely forbidden to carry out
whatever after-market operation involv-
ing steering system or steering column modifica-
tions (e.g.: installation of anti-theft device) that
could badly affect performance and safety, cause
the lapse of warranty and also result in non-com-
pliance of the car with type approval require-
ments.
WARNING
Before starting any servicing operation,
stop the engine and remove the key from
the ignition switch to operate the steering lock,
particularly when the wheels do not touch the
ground. If this is not possible (i.e. if the key must
be kept in the MAR position or the engine must
be kept running), remove the electric power steer-
ing system main fuse.
WARNING
In this case, stop the car immediately, switch off the en-
gine for about 20 seconds and then restart the engine.
If the warning light
g
is still on, along with the message
on the reconfigurable multifunction display (for versions/
markets, where provided), contact a Fiat Dealership.
IMPORTANT The steering may become stiffer following
parking manoeuvres including a great deal of steering.
This is normal and caused by the system preventing the
electric control motor overheating. No repairs are need-
ed. The power steering system will start working properly
again the next time the car is used.
81KNOW YOUR
VEHICLESAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
065-090 PANDA EN 7-10-2009 13:45 Pagina 81

95KNOW YOUR
VEHICLESAFETYCORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0046m
fig. 103
GENERAL INSTRUCTIONS FOR USING
THE SEAT BELTS
The driver must comply with (and have all car passengers
follow) any local regulations in force concerning the use
of seat belts. Always fasten the seat belts before starting.
Seat belts are also to be worn by expectant mothers: the
risk of injury in the case of accident is greatly reduced for
them and the unborn child if they are wearing a seat belt.
Expectant mothers must position the lower part of the
belt very low down so that it passes under the abdomen
(see fig. 103).
The pretensioner can only be used once.
After a collision that has triggered it, have
it replaced at a Fiat Dealership. Pretensioner va-
lidity is written on the label set on the door con-
tour sheet metal. Pretensioners should be replaced
at Fiat Dealership as this date approaches.
WARNING
Operations which lead to knocks, vibrations
or localised heating (over 100 °C for a max-
imum of 6 hours) in the area around the
pretensioners may cause damage or trigger them.
These devices are not affected by vibrations caused
by irregularities of the road surface or low obsta-
cles such as kerbs, etc. Contact a Fiat Dealership
for any assistance.
LOAD LIMITERS
To increase passenger’s safety, the front seat belt reels
contain a load limiter which allows controlled sag in such
a way as to dose the force acting on the chest and shoul-
ders during the belt restraining action in case of front
collisions.
091-110 PANDA EN 7-10-2009 13:46 Pagina 95

112
KNOW YOUR
VEHICLE
SAFETYCORRECT USE
OF THE CARWARNING LIGHTS
AND MESSAGESI
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
If, when the ignition key is at MAR, warning light
Y
re-
mains lit together with warning light
U
turn the key to
STOP and then back to MAR; if the warning light remains
on, try with the other keys provided with the car.
If you are still unable to start the engine, perform the emer-
gency start-up procedure (see “Emergency start-up” in “In
an emergency” chapter) and contact a Fiat Dealership.
STARTING PROCEDURE FOR DIESEL
VERSIONS
Proceed as follows:
❒
engage the handbrake;
❒
put the gearshifting lever into neutral;
❒
turn the ignition key at MAR: the warning lights
m
and
Y
on the instrument panel will turn on;
❒
wait for the warning lights
Y
and
m
to turn off.
The hotter the engine is, the quicker this will happen;
❒
press the clutch pedal all the way down without touch-
ing the accelerator;
❒
turn the ignition key to AVV as soon as the warning lightm
turns off. Waiting too long will waste the work
done by the glow plugs.
Release the key as soon as the engine starts.
IMPORTANT With cold engine, the accelerator must
be entirely released when turning the ignition key to
position AVV.If the engine does not start at the first attempt, return
the ignition key to STOP before repeating starting.
If, when the ignition key is at MAR, the instrument panel
warning light
Y
remains lit, turn the key to STOP
and then back to MAR; if the warning lights remain on,
try with the other keys provided with the car.
If you still cannot start the engine, contact a Fiat Dealership.
Warning light
m
will flash for 60 seconds
after starting or during prolonged cranking
to indicate a fault to the glow plug heating
system. You can use the car as usual if the engine
starts but you should contact a Fiat Dealership as
soon as possible.
HOW TO WARM UP THE ENGINE AFTER IT
HAS JUST STARTED
Proceed as follows:❒
drive off slowly, letting the engine turn at medium speed.
Do not accelerate abruptly;
❒
do not demand maximum performance for the first few
kilometres. Wait until the engine temperature coolant
gauge starts moving.
111-122 PANDA EN 7-10-2009 15:01 Pagina 112

116
KNOW YOUR
VEHICLE
SAFETYCORRECT USE
OF THE CARWARNING LIGHTS
AND MESSAGESI
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
clutching is absolutely pointless on modern cars and also
increases consumption and pollution.
Gear selection
As soon as the conditions of the traffic and road allow, use
a higher gear. Using a low gear for faster acceleration will
increase consumption.
In the same way improper use of a high gear increases con-
sumption, emissions an engine wear.
Top speed
Fuel consumption considerably increases with speed.
Avoiding unnecessary braking and acceleration, which cost
in terms of both fuel and emissions.
Acceleration
Accelerating violently increasing the revs will greatly af-
fect consumption and emissions: acceleration should be
gradual.
CONDITIONS OF USE
Cold starting
Short journeys and frequent cold starts will prevent the en-
gine from reaching optimal running temperature. This re-
sults in a significant increase in consumption levels (from
+15 to +30% on the urban cycle) and emission of harmful
substances. Electric devices
Use electric devices only for the amount of time needed.
Rear heated window, additional headlights, windscreen
wipers and heater fan need a considerable amount of en-
ergy, therefore a higher requirement of current involves
and increase of fuel consumption (up to +25% in the
urban cycle).
Climate control system
The climate control system is an additional load which
greatly affects the engine leading to higher consumption
(on average up to +20%): when the temperature outside
the car permits it, use the air vents where possible.
Devices for aerodynamic control
The use of non-certified devices for aerodynamic control
may adversely affect air drag and consumption levels.
DRIVING STYLE
Starting
Do not warm the engine with the car at a standstill or at
idle or high speed: under these conditions the engine
warms up much more slowly, increasing electrical con-
sumption and emissions. It is therefore advisable to move
off immediately, slowly, avoiding high speeds: in this way
the engine will warm faster.
Unnecessary actions
Avoid accelerating when starting at traffic lights or be-
fore switching off the engine. This and also double de-
111-122 PANDA EN 7-10-2009 15:01 Pagina 116

ABS SYSTEM FAILURE (amber)Turning the ignition key to
MAR
the
warning light turns on, but it should go off
after a few seconds.
The warning light will light up when the system is either
not working or not available. Under these circumstances
the braking system will work as normal without the ex-
tra performance offered by the ABS system. Drive care-
fully and contact a Fiat Dealership as soon as possible.
On some versions the display shows the dedicated message.
125KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CARWARNING LIGHTS
AND MESSAGESIN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
IMPORTANT Under severe use of the car, it is advisable
to keep the engine on and slightly accelerated for a few
minutes before switching it off.
On some versions the display shows the dedicated message. ENGINE COOLANT HIGH TEMPERA-
TURE (red)
Turning the ignition key to MAR the warning light
turns on, but it should go off after a few seconds. The
warning light turns on when the engine is overheated. If
the warning light comes on when driving, proceed as fol-
lows:
❒in standard normal driving conditions: stop the car,
switch off the engine and check whether the water lev-
el in the reservoir is not below the MIN. mark. In this
case, wait for a few minutes for the engine to cool
down, then slowly and carefully open the cap, top-up
with coolant and check that the level is between the
MIN. and MAX. marks on the reservoir itself. Also
check for any fluid leaks. If, when restarting, the warn-
ing light should come on again, contact a Fiat Dealer-
ship.
❒In case of car heavy duty (e.g.: towing trailer uphill or
fully laden car): decrease speed, if the warning light stays
on, stop the car. Wait for 2 or 3 minutes with the en-
gine running and slightly accelerated to further accel-
erate the coolant circulation. Then stop the engine.
Check the correct liquid level as described above.
ç
LOW BATTERY CHARGE (red)
Turning the ignition key to
MAR
, the warning
light turns on and should go out as soon as the
engine is started (with the engine running at idle speed
a short delay in going out is allowed).
If the warning light stays on contact immediately a Fiat
Dealership.
wx
>
123-134 PANDA EN 7-10-2009 13:49 Pagina 125

131KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CARWARNING LIGHTS
AND MESSAGESIN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
CAR PROTECTION SYSTEM FAILURE
- FIAT CODE (amber)
Turning the key to MAR the warning light shall
flash only once and then go off.
If with the ignition key at MAR, the warning light stays on,
a possible failure is indicated (see “Fiat Code system” in
chapter “Know your vehicle”).
IMPORTANT The turning on at the same time of the
warning lights
U
and
Y
indicates a failure of the Fiat
CODE system.
If with the engine running the warning light
Y
flashes, this
means that the car is not protected by the engine immo-
bilizer device (see “Fiat Code system” in chapter “Know
your vehicle”).
Contact a Fiat Dealership to have all the keys repro-
grammed. WATER IN DIESEL FUEL FILTER
(Multijet versions - amber)
Turning the ignition key to MAR the warning light
turns on, but it should go off after a few seconds.
The warning light
c
turns on when there is water in the
diesel fuel filter. On some versions warning light èturns
on as an alternative.
On some versions the display shows the dedicated message.
The presence of water in the feeding circuit
may cause severe damage to the injection
system and irregular engine operation. If
the warning light
c
lights up (on some versions the
warning light èis on together with the message on
the display), contact a Fiat Dealership as soon as
possible to have the system bled. If the same mes-
sage is displayed immediately after refuelling, wa-
ter has probably been poured into the tank: turn
the engine off immediately and contact a Fiat
Dealership.
c
Y
GLOW PLUG PRE-HEATING
(Multijet versions - amber)
GLOW PLUG PRE-HEATING FAILURE
(Multijet versions - amber)
Glow plug pre-heating
This warning light comes on when the key is turned to
MAR. It will go out as soon as the glow plugs have reached
a preset temperature. Start the engine as soon as the warn-
ing light goes out.
IMPORTANT At high ambient temperatures the warning
light stays on for an extremely short time.
Glow plug pre-heating failure
The warning light flashes if there is a failure in the pre-
heating system. Contact a Fiat Dealership as soon as
possible.
On some versions the display shows the dedicated message.
m
123-134 PANDA EN 7-10-2009 13:49 Pagina 131

132
KNOW YOUR
VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
ESP SYSTEM FAILURE (amber)
Turning the ignition key to MAR the warning light
turns on, but it should go off after a few seconds.
If the warning light does not go off or stays on together
with the LED on the button ASR OFF when travelling, con-
tact a Fiat Dealership.
On some versions the display shows the dedicated message.
NOTE The warning light flashing when driving indicates
that the ESP system is active.
á
GENERIC FAILURE INDICATION
(amber)
The warning light turns on in the following cir-
cumstances.
Engine oil pressure sensor failure
The warning light turns on when failure is detected in en-
gine oil pressure sensor. Contact a Fiat Dealership to have
the failure fixed as soon as possible.
Water in diesel fuel filter
See what described for warning light
c.
Inertia fuel cut-off switch tripped
The warning light comes on when the inertia fuel cut-off
switch is triggered. The display shows the dedicated
message.
è
EXTERNAL LIGHT FAILURE (amber)
The warning light will come on (some versions
only) when a failure to one of the following lights
is detected:
– side lights;
– brake lights (third brake light excluded);
– rear fog lights;
– direction indicators;
– number plate lights.
The failure referring to these lights could be: one or more
blown bulbs, a blown protection fuse or an electric con-
nection cut-off.
The display shows the dedicated message.
W
REAR FOG LIGHTS (amber)
The warning light turns on when the rear fog
lights are turned on.
4
HEATED REAR WINDOW (amber)
The warning light turns on when switching the
heated rear window on.
(
123-134 PANDA EN 7-10-2009 13:49 Pagina 132

145KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
Tyre side wall holes and punctures cannot
be repaired. Do not use the quick repair
kit if the tyre is damaged as the vehicle has run on
a flat tyre.
WARNING
If the wheel rim is damaged (bad groove
distortion causing air leakage) it cannot
be repaired. Do not remove the foreign body
(screws or nails) from the tyre.
WARNING
PLEASE REMEMBER THAT:
The sealing fluid of the quick tyre repair kit is effective with
external temperatures between −20 °C and +50 °C.
The sealing fluid has a limited life.
Never not operate the compressor for
longer than 20 consecutive minutes. Risk
of overheating. The quick repair kit is not suitable
for definitive repairs. Tyres may only be repaired
temporarily.
WARNING
The bottle contains ethylene glycol. It con-
tains latex that might cause allergic reac-
tions. It is harmful if swallowed. It is irritant for the
eyes in case of contact. It may cause sensitisation
by inhalation or contact. Avoid contact with your
eyes, skin and clothes. In the event of contact, wash
immediately with plenty of water. Do not induce
vomit if swallowed. Rinse your mouth and drink
plenty of water. Call a doctor immediately. Keep
away from children. The product must not be used
by asthmatics. Do not inhale the vapours during in-
sertion and suction. Call a doctor immediately if al-
lergic reactions are noted. Store the bottle in the
specific compartment, away from sources of heat.
The sealant fluid has a limited life.
WARNING
135-168 PANDA EN 7-10-2009 14:07 Pagina 145

163KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
5
7,5
7,5
10
7,5
15
15
7,5
7,5
7,5
7,5
5
5
15
–
–
7,5
7,5
7,5
20
10
10
10
10
F31
F35
F35
F37
F41
F45
F46
F49
F49
F49
F50
F51
F51
F54
FA
FB
F12
F13
F13
F38
F39
F39
F39
F39
FUSE SUMMARY TABLEPassenger’s compartment fuse-box - fig. 167 FUSE AMPEREReversing lights+15 radioCentral dashboard+15 stop lightsDoor mirror defroster Heated seats (pre-arrangement)Electric sun roofAutomatic climate control systemTyre pressureSensor for water presence in the diesel fuel filter +15 air bag control unit+15 Body-computer control unit+15 instrument panelSubwooferFreeFreeRight dipped beam headlightLeft dipped beam headlightHeadlight aiming adjustment+ 30 door locking deviceEOBD diagnosis socketRadioAutomatic climate control systemTyre pressure
135-168 PANDA EN 7-10-2009 14:07 Pagina 163

164KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
10
10
30
30
15
20
20
15
F39
F39
F40
F43
F53
F47
F48
F52
Passenger’s compartment fuse-box - fig. 167 FUSE AMPERETelephoneBody-computer control unitHeated rear windowWindscreen wiper/washerWindscreen/rear window washer pumpFront left power windowFront right power windowRear window wiper
30
20
15
15
15
15
7,5
10
7,5
F8
F9
F10
F11
F14
F15
F16
F17
F18
Engine compartment fuse-box - fig. 169 FUSE AMPEREClimate control system fanHeadlight washersHornSecondary services and odometer generatorMain beam headlights+ 30 trailer unit
Electronic injection and supply system +15 Dualogic transmission control unitElectronic injection primary services+30 engine control node
135-168 PANDA EN 7-10-2009 14:07 Pagina 164