lock FORD AEROSTAR 1996 1.G Owner's Manual

76 [LG03700(ALL)07/95]Rear Anti-Lock (ABS) Brake Warning Light
[LG03900(ALL)05/95]
To check the rear ABS brake warning light turn
the ignition key to the ON position. The rear
ABS brake warning light should glow
momentarily.
*
[LG03950(ALL)06/94]
NOTE: If it does not glow momentarily, have
your vehicle's electrical system checked
immediately.
[LG03975(ALL)07/95]
NOTE: If the rear ABS brake warning light
begins to flash in a repeating flash
sequence, check the rear anti-lock
brake system continuous power fuse
and brake lights for proper operation.
[LG04000(ALL)05/95]
one inch art:0095035-A
Rear anti-lock warning light symbol
*
[LG04100(ALL)05/95]
RWARNING
If the anti-lock brake system warning
light remains on or comes on while
driving, have the braking system checked
by a qualified service technician as soon
as possible.
*
[LG04110(ALL)07/95]
NOTE: If a fault occurs in the anti-lock
system, and the brake warning light is
not lit, the anti-lock system is disabled
but normal brake function remains
operational.
File:05cplga.ex
Update:Tue Aug 29 17:36:50 1995

87 %
*
[LG12601(ALL)01/95]
Speedometer
*
[LG12700(ALL)01/95]
The speedometer tells you how many miles
(kilometers) per hour your vehicle is moving.
*
[LG12750(ALL)08/95]
Your vehicle contains a speedometer which
receives its input from the Anti-Lock brake
sensor. The speedometer is also used to provide
a speed signal for correct operation of the
vehicle's Powertrain Control Module (PCM),
electronic transmission, and speed control (if so
equipped). Because of this, it is very
IMPORTANT to change the speedometer's
internal conversion constant if the size of the
tires on the vehicle is changed. Changing the
conversion constant to the proper value when
the tires are changed will also ensure that the
speedometer retains the original factory-set
accuracy.
[LG12752(ALL)08/95]
NOTE: The conversion constant can only be
changed six times once the vehicle
leaves the factory. Your Ford dealership
service personnel can change the
conversion constant.
*
[LG12753(ALL)08/95]
Some vehicles are equipped with a vehicle speed
(mph/km/h) limiting device that is contained
within the Powertrain Control Module (PCM).
The purpose of this device is to maintain peak
vehicle speed below a specified limit. (Vehicle
speed limits may vary based on engine
displacement.)
File:05cplga.ex
Update:Tue Aug 29 17:36:50 1995

115
*
[SC06750(ALL)04/95]
To change the position of the steering wheel,
pull the release lever on the column toward you.
Tip the steering wheel to the desired position.
Release the lever to lock the steering wheel in
place.
*
[SC07250(ALL)12/89]
Be sure the steering wheel locks in a notch. It is
not infinitely adjustable. Do not adjust the
steering wheel while the vehicle is in motion.
%
*
[SC07300(ALL)03/91]
Speed Control (If equipped)
[SC07700(ALL)06/95]
one third page art:0095006-A
Speed control switches on the steering wheel
File:07cpsca.ex
Update:Tue Aug 29 17:38:34 1995

121
Features
*
[FV00501(ALL)02/95]
Your vehicle has a variety of features designed
for your comfort, convenience and safety. Read
this chapter to find out about standard and
optional features.
%
*
[FV00601(ALL)01/95]
Doors
*
[FV00701(ALL)06/95]
Door Handles and Locks
[FV01000(ALL)03/91]
half page art:0020178-B
Inside handles
File:08cpfva.ex
Update:Tue Aug 29 17:41:55 1995

122 [FV01401(ALL)03/91]
one third page art:0020834-AOutside handles and locks
%*
[FV01801(ALL)03/95]
Anti-theft front door lock knobs
*
[FV01901(ALL)10/89]
Anti-theft lock knobs are designed to preclude
unlocking the door by pulling up on the bullet
type lock knob. To unlock and open the front
door from the inside of the vehicle, pull on the
inside door handle.
*
[FV03801(ALL)04/95]
Sliding Door
[FV03901(ALL)08/95]
With the door unlocked, unlatch the sliding door
by pulling the inside handle to the rear, or by
pulling the outside handle out and rearward. To
close, push the inside handle forward or pull the
outside handle forward.
[FV04101(ALL)11/89]
quarter page art:0020188-B
Sliding door handles
File:08cpfva.ex
Update:Tue Aug 29 17:41:55 1995

123
*
[FV04301(ALL)01/89]
Liftgate opening procedure
[FV04401(ALL)07/95]
1. Insert the key into the lock and turn it
counterclockwise. You can also unlock the
latch (but not release it) with the power door
lock system (if equipped).
*
[FV04500(ALL)01/89]
2. Reach under the license plate light shield
and release the liftgate latch by squeezing
the paddle handle rearward.
[FV04600(ALL)03/94]
3. To make the gate swing up to the fully
opened position, pull back and upward on
the latch paddle handle.
[FV04800(ALL)10/90]
one third page art:0020190-B
Opening the liftgate
*
[FV05300(ALL)10/89]
Make certain that you close the liftgate door and
window before driving your vehicle. If you do
not, possible damage may occur to the liftgate
door lift cylinders and attaching hardware.
*
[FV05400(ALL)08/95]
RWARNING
When driving your vehicle make sure that
the liftgate door and window are closed to
prevent exhaust fumes from being drawn
into the vehicle. This will also prevent
cargo from falling out.
File:08cpfva.ex
Update:Tue Aug 29 17:41:55 1995

124
*
[FV05500(ALL)01/89]
Liftgate closing procedure
*
[FV05600(ALL)01/89]
1. To make the liftgate swing downward, reach
up and pull the lower edge of the liftgate (or
the loop handle on the inner trim panel of
vehicles with this option) and pull
downward.
*
[FV05700(ALL)01/89]
2. When you have pulled down the liftgate
enough so that you can reach the license
plate light shield, push the shield down and
forward to close the latch and liftgate. At
this point, the latch is not locked.
[FV05800(ALL)07/95]
3. You can lock the liftgate latch by pushing
down the lock button before you pull down
and close the liftgate. You can also lock the
liftgate latch by inserting your vehicle's door
key and turning it clockwise after you have
closed the liftgate, or by using the power
door locks (if equipped).
*
[FV05900(ALL)12/93]
The liftgate area is only intended for cargo, not
passengers. You can open and close the liftgate
from outside the vehicle. It cannot be opened
from inside the cargo area.
File:08cpfva.ex
Update:Tue Aug 29 17:41:55 1995

126 %
*
[FV14100(ALL)04/95]
Power Door Locks (If equipped)
[FV14200(ALL)03/91]
The power door lock switches are located in the
front doors. To lock all doors push the switch
marked LOCK. To unlock all doors push the
switch marked UNLOCK.
*
[FV14300(ALL)03/94]
Memory lock (sliding door)
[FV14401(ALL)08/95]
Your vehicle has a sliding door memory lock
feature that does not require the sliding door to
be closed before using the power locks. The
locking function will activate after the door is
closed.
*
[FV14701(ALL)03/91]
The manual door locks will override the power
door lock controls.
[FV14801(ALL)05/91]
quarter page art:0020201-C
Power door lock controls
File:08cpfva.ex
Update:Tue Aug 29 17:41:55 1995

132
*
[FV32200(ALL)12/91]
To install the rear bucket seat:
[FV32300(ALL)12/91]
1. Lift the seat assembly into the vehicle and
drop the front and rear floor hooks into the
floor wells at a point just behind the floor
attachment pins.
[FV32500(ALL)05/89]
2. Rotate the seat latch handle forward, causing
the J hook to engage over the front of the
foremost well retainer.
[FV32801(ALL)02/92]
3. For right hand seats, continue rotating the
seat latch handle until it comes to a
complete stop on the top of the tube. This
will cause the seat assembly to slide forward,
engaging the front and rear floor hooks with
the floor well retainers.
[FV32901(ALL)02/92]
For left hand seats, push the seat latch
handle downward to a full stop. This locks
the seat in position. Before you engage the
safety belt, be sure it is not twisted. Remove
any twist, then insert the tongue end of the
detachable anchor into the detachable anchor
until you hear a ªsnapº and feel the latch
engage.
*
[FV33300(ALL)05/95]
RWARNING
Check to see that the seat is latched
securely in position. Keep floor area free
of objects that would prevent proper seat
engagement. Never attempt to adjust the
seat latch while the vehicle is in motion.
File:08cpfva.ex
Update:Tue Aug 29 17:41:55 1995

140 [FV36001(ALL)06/95]
half page art:0095041-AInstallation and removal of the second and third passenger
bed and bench seat
*
[FV38301(ALL)05/95]
RWARNING
Never adjust the driver's seat or seatback
when the vehicle is moving.
*
[FV38350(ALL)05/95]
RWARNING
Always latch the vehicle seat to the floor,
whether the seat is occupied or empty. If
not latched, the seat may cause injury
during a sudden stop.
*
[FV38401(ALL)05/93]
RWARNING
Before using the seat, make sure that the
latch hooks are securely locked around the
floor pins.
File:08cpfva.ex
Update:Tue Aug 29 17:41:55 1995