lock FORD CONTOUR 1997 2.G Owner's Manual

Seating and Safety Restraints
91
% [SS05400(ALL)12/95]
Dual Locking Mode Lap/Shoulder Belt Retractor
[SS05500(ALL)12/95]
The front passenger seat and the rear outer seat combination lap
and shoulder belts are equipped with a dual locking mode
retractor on theshoulderbelt portion of the lap/shoulder belt.
This retractor can be switched from vehicle sensitive
(emergency) locking mode to automatic locking mode by pulling
the belt webbing all of the way out of the retractor. The
retractor modes function as follows.
*
[SS05600(ALL)02/96]
Vehicle sensitive (emergency) locking mode
[SS05700(ALL)12/95]
In this operating mode, the lap/shoulder belt retractor will
allow the occupant freedom of movement, locking tight only on
hard braking, hard cornering or impacts of approximately
5 mph (8 km/h) or more.
%*
[SS05800(ALL)02/96]
Automatic locking mode
*
[SS05900(ALL)12/95]
This mode must be used when installing a child seat on the
front passenger seat and rear seats where dual locking retractors
are provided. To switch the retractor from the emergency
locking mode to the automatic locking mode, perform the
following steps:
*
[SS06000(ALL)03/96]
RWARNING
Rear-facing child seats or infant carriers should never be
placed in the front seats.
*
[SS06100(ALL)02/96]1.
Buckle the lap/shoulder combination belt.
*
[SS06200(ALL)12/95]2.
Grasp the shoulder portion of the belt and pull downward
until all of the belt is extracted and a click is heard. At this
time, the retractor is in the automatic locking mode (child
restraint mode).
*
[SS06300(ALL)12/95]3.
Allow the belt to retract. A clicking sound will be heard as
the belt retracts. This indicates that the retractor is in the
automatic locking mode.
File:06cdsso.ex
Update:Thu Sep 12 11:03:20 1996

92
[SS06400(ALL)12/95]4.
Pull up on the shoulder belt to remove slack in the lap belt.
*
[SS06500(ALL)02/96]
NOTE: When the combination lap/shoulder belt is unbuckled
and allowed to retract completely, the retractor will
switch to the vehicle sensitive (emergency) locking
mode. See the detailed instructions underSafety Seats
for Childrenin this chapter.
%*
[SS06600(ALL)01/96]
Shoulder Belt Height Adjustment
*
[SS06700(ALL)01/96]
Driver and right front passenger
[SS06800(ALL)12/95]
You can adjust the shoulder belt height to one of four (4)
positions.
*
[SS06900(ALL)12/95]
To adjust the belt down, push the release button (see figures 1
and 2). To adjust the belt up, slide the adjuster up. (You do not
have to push the release button.)
[SS07000(ALL)12/95]
17-1/2 pica
art:0001183-C
Figure 1 Ð The shoulder belt height adjuster
File:06cdsso.ex
Update:Thu Sep 12 11:03:20 1996

Seating and Safety Restraints
93
[SS07100(ALL)12/95]
10-1/2 pica
art:0001184-D
Figure 2 Ð Adjusting the shoulder belt height
[SS07200(ALL)12/95]
Make sure the adjuster is firmly in one of the four positions.
The belt should be adjusted up or down until the belt rests on
your shoulder near your neck.
*
[SS07300(ALL)01/96]
RWARNING
Position the shoulder belt height adjuster so that the belt
rests across the middle of your shoulder. Be sure the
shoulder belt is properly positioned on your shoulder
each time you use the belt. If the shoulder belt is off
your shoulder, on your upper arm or neck, there is a
greater risk of severe injury in a collision.
%*
[SS07400(ALL)12/95]
Lap Belts
*
[SS07500(ALL)12/95]
The lap belt in the center of the rear seat does not adjust
automatically. You must adjust it to fit snugly and as low as
possible around your hips. Do not wear it around your waist.
*
[SS07600(ALL)01/96]
Pull the belt across your hips andinsert the tongue into the
correct buckleon your seat until you hear a snap and feel it
lock. Make sure the buckle is securely fastened.
File:06cdsso.ex
Update:Thu Sep 12 11:03:20 1996

Seating and Safety Restraints
103
*
[SS14800(ALL)01/96]
All child restraint systems are designed to be secured in vehicle
seats by lap belts or by the lap portion of a lap-shoulder belt.
*
[SS14900(ALL)03/96]
RWARNING
If you do not properly secure the safety seat, the child
occupying the seat may be injured during a collision or
sudden stop. An unsecured safety seat could also injure
other passengers.
*
[SS15000(ALL)03/96]
RWARNING
Carefully follow all of the manufacturer's instructions
included with the safety seat you put in your vehicle. If
you do not install and use the safety seat properly, the
child may be injured in a sudden stop or collision.
*
[SS15100(ALL)01/96]
When installing a child safety seat, be sure to use the correct
safety belt buckle for that seating position, and make sure the
tongue is securely fastened in the buckle. For a shoulder/lap
belt combination with a sliding tongue, make sure the retractor
is in the automatic locking mode.
*
[SS15200(ALL)03/96]
RWARNING
Always keep the buckle release button pointing upward
and away from the child seat, with the tongue between
the child seat and the release button as shown in the
following illustration.
File:06cdsso.ex
Update:Thu Sep 12 11:03:20 1996

104
[SS15300(ALL)12/95]
17-1/2 pica
art:0001209-B
Safety belt buckle placement for child seats
%*
[SS15400(ALL)12/95]
Installing Child Safety Seats in the Front Passenger
Seat and Outer Rear Seating Positions
[SS15500(ALL)12/95]
Your vehicle is equipped with a dual locking mode retractor on
the shoulder belt portion of the combination lap/shoulder safety
belt for the right front seat passenger and rear outer passengers.
*
[SS15600(ALL)12/95]
If you choose to install a child safety seat in the front seating
position, move vehicle seat as far back as possible.
*
[SS15700(ALL)12/95]1.
Position the child seat in center of passenger seat.
*
[SS15800(ALL)02/96]2.
Pull down on shoulder belt, then grasp shoulder belt and lap
belt together. See Figure 1.
File:06cdsso.ex
Update:Thu Sep 12 11:03:20 1996

108
[SS16300(ALL)02/96]4.
Grasp the shoulder portion of the belt and pull downward
until all of the belt is extracted from the reel and a click is
heard. At this time the retractor is in the automatic locking
mode (child restraint mode). See Figure 4.
[SS16400(ALL)12/95]
24 pica art:0001273-AFile:06cdsso.ex
Update:Thu Sep 12 11:03:20 1996

Seating and Safety Restraints
109
*
[SS16500(ALL)02/96]5.
Allow the belt to retract. Pull up on the shoulder webbing. A
clicking sound will be heard as the belt retracts. This
indicates the retractor is in the automatic locking mode. Push
down on the child seat while you pull up on the belt to
remove any slack in the belt. See Figures 5 and 6.
[SS16600(ALL)12/95]
17-1/2 pica
art:0001274-BFile:06cdsso.ex
Update:Thu Sep 12 11:03:20 1996

112
*
[SS17000(ALL)02/96]7.
Double check that the retractor is in the automatic locking
mode. Try to pull more belt out of the retractor. If you
cannot, the belt is in the automatic locking mode. See
Figure 8.
[SS17100(ALL)12/95]
17-1/2 pica
art:0001277-B[SS17200(ALL)12/95]8.
Check to make sure that the child seat is properly secured
prior to each use. If the belt is not locked, repeat steps 4
through 7.
[SS17300(ALL)12/95]
To remove retractor from automatic lock mode, unbuckle the
belt and allow the webbing to retract fully. A click will be
heard as the belt retracts. The belt is back in normal operating
mode (vehicle sensitive emergency locking mode) when this
click disappears.
File:06cdsso.ex
Update:Thu Sep 12 11:03:20 1996

Starting
119
[TO03200(ALL)12/95]
n
At temperaturesbetween-10ÊF (-23ÊC) and 10ÊF(-12ÊC):
Turn the key to ON, and crank the engine forfive (5)
seconds.If the engine fails to start, continue to crank and
depress the accelerator about 1/4 of the way down and hold
that position until the engine starts.DO NOT crank for
more than 30 seconds,or you could damage the starter. If
the engine fails to start on the first try, turn the key to OFF
and wait two (2) minutes before trying again.
[TO03300(ALL)12/95]
n
At temperaturesbetween10ÊF (-12ÊC) and 32ÊF (0ÊC):If the
engine does not start infifteen (15) secondson first try, turn
the key to OFF, then try again.
[TO03400(ALL)12/95]
n
At temperaturesabove32ÊF (0ÊC):If the engine does not
start infive (5) secondson the first try, turn the key to OFF,
then try again.
[TO03500(ALL)12/95]
If you have the 4-cylinder 2.0L engine and are not using an
engine block heater, warm up the engine for a minute or two
before putting the transaxle in gear. Depressing the accelerator
slightly will also help with cold starts.
[TO03600(ALL)12/95]
2.5L engine:
*
[TO03700(ALL)01/96]
n
At temperatures10ÊF (-12ÊC) andbelow:If the engine does
not start infifteen (15) secondson the first try, turn the key
to OFF, wait approximately ten (10) seconds so you do not
flood the engine, then try again.
[TO03800(ALL)12/95]
n
At temperaturesabove10ÊF(-12ÊC):If the engine does not
start infive (5) secondson the first try, wait approximately
ten (10) seconds so you do not flood the engine, then try
again.
File:08cdtoo.ex
Update:Thu Sep 12 11:03:39 1996

120
%*
[TO03900(ALL)01/96]
For a warm engine:
[TO04000(ALL)12/95]
n
Do not hold the key in the START position for more than
five (5) secondsat a time. If the engine does not start within
five (5) seconds on the first try, wait a few seconds after the
starter stops, then try again.
*
[TO04100(ALL)01/96]
Whenever you start your vehicle, release the key as soon as the
engine starts. Excessive cranking could damage the starter.
*
[TO04200(ALL)01/96]
After you start the engine, let it idle for a few seconds. Keep
your foot on the brake pedal and put the gearshift lever in gear.
Release the parking brake. Slowly release the brake pedal and
drive away in the normal manner.
*
[TO04300(ALL)12/95]
NOTE: If your vehicle is equipped with an automatic
transaxle, your vehicle has an interlock that prevents
you from shifting out of P (Park) unless your foot is
on the brake pedal.
%*
[TO04400(ALL)01/96]
If the engine does not start after two attempts:
[TO04500(ALL)12/95]1.
Press the accelerator pedal all the way to the floor and hold
it.
[TO04600(ALL)12/95]2.
Turn the ignition key to the START position.
[TO04700(ALL)12/95]3.
Release the ignition key when the engine starts.
[TO04800(ALL)12/95]4.
Release the accelerator gradually as the engine speeds up.
Then drive away in the normal manner.
*
[TO04900(ALL)03/96]
If the engine still does not start, the fuel pump shut-off switch
may have been triggered. For directions on how to reset the
switch seeFuel Pump Shut-Off Switchin the index.
File:08cdtoo.ex
Update:Thu Sep 12 11:03:39 1996