air con FORD FIESTA 2007 Workshop Manual

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-63 Duratec-1 6V (Sigma)/l.6L Duratec-1 6V (Sigma) 303-01 A-63
IN-VEHICLE REPAIR
23. Connect the brake booster vacuum line to 27. Install the
exhaust manifold lower heat
the intake manifold. shield
left-hand retaining bolts.
24. Raise and support the vehicle. 28.
N0TE:lnstall a
new flexible pipe gasket and
For
additional information, refer to: Lifting new
nuts.
(1 00-02 Jacking and Lifting, Description Attach the flexible pipe to the catalytic
and Operation). converter
25.
Install the intake manifold retaining bolt.
29. Remove the exhaust flexible pipe support.
26. Position the exhaust
manifold lower heat . 30, Install the camshaft.
shield and install the right-hand retaining
For additional information, refer to:
bolts. Camshafts (303-01 Engine
- 1.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V
(Sigma)ll.GL Duratec-1 6V (Sigma),
In-vehicle Repair).
31.
N0TE:lnstall a new oil filter.
Change the engine oil.
32. Fill and bleed the cooling system.
For
additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling - 1.4L
Duratorq-TDCi (DV) Diesel, General
Procedures).
2006.0 Fiesta 1212006 GI 83740en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llm4L
303-01 A-66 Duratec-1 6V (Sigma)/l.GL Duratec-1 6V (Sigma) 303-01 A-66
IN-VEHICLE REPAIR
Oil Pump(21 714 0)
Special Tool(s)
Removal
1. Remove the timing belt.
For additional information, refer to Timing
Belt in this section.
2. Remove the crankshaft timing belt pulley.
3. Detach the air conditioning (AIC) compressor
from the cylinder block and position
it to one
side.
4. Remove the oil pan.
For additional information, refer to Oil Pan
in this section.
5. Detach the oil pick-up tube from the oil pump
and remove the oil pump (engine shown
removed for clarity).
Discard the gaskets.
Remove and discard the crankshaft front oil
seal.
Installation
1. N0TE:lnstall a new oil pump gasket.
Install the oil pump (engine shown removed
for clarity).
2. N0TE:lnstall a new oil pump intake pipe
gasket.
2006.0 Fiesta 1212006 GI 83742en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llI4L
303-01 A-67 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-01 A-67
IN-VEHICLE REPAIR
Attach the oil pick-up tube to the oil pump 6. Install the crankshaft timing belt pulley.
(engine shown removed for clarity).
7. Install the timing belt.
3. N0TE:lnstall a new crankshaft front oil seal.
For additional information, refer to Timing
Using the special tool, install the crankshaft Belt
in this section.
front oil seal.
4. Install the oil pan.
For additional information, refer to Oil Pan
in this section.
5. Attach the air conditioning (AIC) compressor
to the cylinder block.
2006.0 Fiesta 1212006 GI 83742en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-70 Duratec-I 6V (Sigma)lll6L Duratec-1 6V (Sigma) 303-01 A-70
REMOVAL
Engine
Special Tool(s)
I I Removerllnstaller, Hose
622
General Eaui~ment
Wrench, Hydraulic Line Union
!:!-269 ( 1 3-027)
I Engine hoist I
I Securing straps I
I Workshop table I
Removal
All vehicles
A WARNING:Do not smoke or carry lighted
tobacco or open flame of any type when
working on or near any fuel related
components. Highly flammable mixtures
are always present and may ignite. Failure
to follow these instructions may result in
personal injury.
1. Release the fuel system pressure.
For additional information, refer to: Fuel
System Pressure Release (31 0-00 Fuel
System
- General Information, General
Procedures).
2. Remove the air cleaner.
For additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling - 1.4L
Duratorq-TDCi (DV) Diesel, General
Procedures).
3. Drain the cooling system.
For additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling - 1.4L
Duratorq-TDCi (DV) Diesel, General
Procedures).
4. Remove the front wheels and tires.
For additional information, refer to: Wheel
and Tire (204-04 Wheels and Tires, Removal
and Installation).
5. Disconnect the powertrain control module

(PCM) electrical connector.
For additional information, refer to:
Powertrain Control Module (PCM)
- 1.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V
(Sigma)ll .6L Duratec-1 6V (Sigma) (303-1 4
Electronic Engine Controls, Removal and
Installation).
6. Loosen the strut and spring assembly top
mount nuts by three turns on both sides.
2006.0 Fiesta 1212006 GII 31 63en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)lIl4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
REMOVAL
19. Disconnect the EVAP electrical connector. 22.
Disconnect the knock sensor (KS) electrical
connector.
20. Disconnect the low pressure evaporate
emission (EVAP) hose from the EVAP valve. 23.
Disconnect the generator electrical
connectors.
21. Detach the brake booster vacuum line from
the intake manifold. 24.
Remove the right-hand
headlamp assembly.
For additional information, refer to:
Headlamp Assembly (41 7-01 Exterior
Lighting, Removal and Installation).
25. Disconnect the air conditioning
(AIC)
lower-pressure cut-off switch electrical
connector.
2006.0 Fiesta 1212006 GI 131 63en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-76 Duratec-1 6V (Sigma)lll6L Duratec-1 6V (Sigma) 303-01 A-76
REMOVAL
Support the exhaust flexible pipe with a
suitable support wrap or suitable splint. 43.
Detach the power steering line support
bracket from the engine block.
/' -
40. Detach the exhaust flexible pipe from the
44. Disconnect the power steering line from
catalytic converter. the steering pump.
Discard the nuts and the gasket.
Allow the fluid to drain into a suitable
container.
41. Remove the accessory drive belt.
For additional information, refer to: 45.
Using the special tool, detach the power
Accessory Drive Belt
- I .4L Duratec-16V steering line from the power steering pump.
(Sigma)ll.GL Duratec-1 6V (Sigma), Allow the fluid to drain into a suitable
Vehicles With: Air Conditioning (303-05 container.
Accessory Drive, Removal and
Installation).
42. Detach the
AIC compressor from the
cylinder block and position
it to one side.
2006.0 Fiesta 1212006 GII 31 63en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-0 I Am82 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
303-01 Am82
REMOVAL
Lifting Bracket, Engine
303-1 22 (21 -068A)
Engine - Vehicles With: Automatic Transaxle
Special Tool(s) present and may ignite. Failure to follow (.
2. Remove the air cleaner.
622
For additional information, refer to: Air
Cleaner - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)/l .6L Duratec-1 6V
(Sigma) (303-12 Intake Air Distribution and
Filtering, Removal and Installation).
I I 1 3. Drain the cooling system.
Wrench, Hydraulic Line Union
"-269 (13-027)
I I Remover/lnstaller, Hose I
these instructions may result in personal
injury.
1. Release the fuel system pressure.
For
additional information, refer to: Fuel
System Pressure Release (31 0-00 Fuel
System - General Information, General
Procedures).
General Eaui~ment
I Engine hoist I
I Securing straps I
I Workshop table I
All vehicles
WARNINGS:
A Refer to the Material Safety Data Sheets
for the Automatic Transmission
Fluid
E-AW. Failure to follow this instruction may
result in personal injury. Certain
Transmission and Power Steering fluids
supplied to Ford contain additives which
may cause skin irritation or other skin
reactions after contact.
For
additional information, refer to: Health
and Safety Precautions (1 00-00 General
Information, Description and Operation).
See
- Transmission Fluids.
A Do not smoke or carry lighted tobacco or
open flame of any type when working on
or near any
fuel related components.
Highly flammable vapors are always
For additional information, refer to: Cooling
System Draining, Filling and Bleeding -
1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma)llm3L Duratec-8V (Rocam) (303-03A,
General Procedures). ,'
4. Remove the front wheels and tires. C'
For additional information, refer to: Wheel
and Tire (204-04 Wheels and Tires, Removal
and Installation).
5. Disconnect the powertrain control module
(PCM) electrical connector.
For
additional information, refer to:
Powertrain
Control Module (PCM) - 1.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V
(Sigma)ll .6L Duratec-1 6V (Sigma) (303-14
Electronic Engine Controls, Removal and
Installation).
6. Loosen the strut and spring assembly top
mount nuts by three turns on both sides.
--
2006.0 Fiesta 1212006 G380458en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-89 Duratec-1 6V (Sigma)ll.GL Duratec-1 6V (Sigma) 303-01 A-89
REMOVAL
44m ACAUTION:~~~~ bending of the exhaust Vehicles with air conditioning
I flexible pipe may cause damage resulting 47.
Disconnect the air conditioning (NC)
, in failure. low-pressure cutoff switch electrical
Support the exhaust
flexible pipe with a connector.
suitable support
wrap or suitable splint.
48. Disconnect the NC compressor clutch
45. Detach the exhaust flexible pipe from the electrical connector.
catalytic converter.
Discard the nuts and the gasket.
46. Remove the accessory drive belt.
For additional information, refer to:
Accessory Drive
Belt - I .4L Duratec-I 6V
(Sigma)ll .6L Duratec-1 6V (Sigma),
Vehicles With: Air Conditioning (303-05
Accessory Drive, Removal and
Installation)
I Accessory Drive Belt - I .4L Duratec-I 6V
(Sigma)ll .6L Duratec-1 6V (Sigma),
Vehicles Without: Air Conditioning
(303-05 Accessory Drive,
Removal and
Installation).
49. Disconnect the NC high-pressure cutoff
switch
electrical connector.
2006.0 Fiesta 1212006 G380458en
procarmanuals.com

303-01 A-I 26 Engine
- 1.25L Duratec-I 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L
Duratec-1 6V (Sigma) 303-01A-I26
INSTALLATION
23. Attach the air conditioning (NC)
compressor to the
cylinder block.
27. Connect the reversing lamp switch
electrical connector.
I
24. Connect the NC compressor clutch
28. Connect the crankshaft position (CKP)
electrical connector. sensor electrical connector.
25. Install the accessory drive belt. 29. Connect the oil pressure switch electrical
For
additional information, refer to: connector.
Accessory Drive
Belt - I .4L Duratec-16V
(Sigma)ll .6L Duratec-1 6V (Sigma),
Vehicles With: Air Conditioning (303-05
Accessory Drive,
Removal and
Installation).
26. Connect the starter motor electrical
connectors.
30.
N0TE:lnstall new exhaust flange nuts and
a new exhaust
flange gasket.
2006.0 Fiesta 1212006 Gll3164en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-I 27 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
303-01 A-I 27
INSTALLATION
Attach the exhaust flexible pipe to the
33. Attach the gearshift cables to the bracket
catalytic converter.
and turn the abutment sleeves
counterclockwise.
31. Remove the exhaust flexible pipe support.
Vehicles without automated gearshift
32m ACAUTION:H brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
N0TE:Make sure the spring clip is correctly seated.
Connect the clutch slave cylinder supply
line.
Install the spring clip.
34. N0TE:Do not install the air cleaner at this
stage.
Adjust the gearshift cable.
For additional information, refer to: Gearshift Cable Adjustment (308-00 Manual
Transmission/Transaxle and Clutch
General Information, General Procedures).
35.
N0TE:Do not install the air cleaner at this
stage.
Bleed the hydraulic clutch system.
For additional information, refer to: Clutch
System Bleeding (308-00 Manual
Transmission/Transaxle and Clutch -
General Information, General Procedures).
Vehicles with automated gearshift
36. Connect the gearshift actuator electrical
connector (colored grey).
2006.0 Fiesta 1212006
procarmanuals.com