air con FORD FIESTA 2007 Workshop Manual

303-01 B-51 Engine - 2.OL Duratec-HE (M14) 303-01 B-51
IN-VEHICLE REPAIR
16. Using the special tool, remove the oil pan. Install the
oil pan.
1
Installation 5. N0TE:Do not tighten the transaxle lower
retaining bolts at this stage.
I. Clean the mating faces of the cylinder block,
Install the transaxle lower retaining bolts.
the oil pan and the engine front cover with
cleaner.
2. Apply a 3 mm bead of sealant to the oil pan.
3. N0TE:lnstall the oil pan within 10 minutes
of applying the silicone sealant and tighten
the retaining bolts within a further
5 minutes.
Apply a 3 mm bead of sealant to the oil pan.
4. N0TE:Do not tighten the oil pan retaining
bolts at this stage. 6.
Install the engine front cover lower retaining
bolts.
2006.0 Fiesta 1212006 G451306en
procarmanuals.com

303-01 B-53 Engine - 2.OL Duratec-HE (M14) 303-01 B-53
IN-VEHICLE REPAIR
14. Tighten the transaxle upper retaining bolts.
15. Install the oil level indicator and oil level
indicator tube upper retaining bolt.
16. Install the air cleaner.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (303-12
Intake Air Distribution and Filtering,
Removal and Installation).
17. Connect the battery.
For additional information, refer to: Battery
Disconnect
(414-01 Battery, Mounting and
Cables, General Procedures).
18. Fill the engine with engine oil.
For additional information, refer to:
Specifications
(303-01 Engine - 2.OL
Duratec-HE (M14), Specifications).
2006.0 Fiesta 1212006 G451306en
procarmanuals.com

303-01 B-56 Engine - 2.OL Duratec-HE (M14) 303-01 B-56
IN-VEHICLE
REPAIR
Crankshaft Rear Seal(21 468 4)
Special Tool(s) Install the drain plug.
Materials Name
S~ecification
1 Cleaner I WSK-M2G342-A I
5. Remove the oil level indicator tube lower
retaining bolt.
- -
d 21 135
4 21 179
I Silicone Sealant I WSE-M4G323-A4 I
Locking Tool, Flywheel
303-254 (2 1 -1 35)
Separator, Oil Pan
303-428 (21 -1
79)
Removal
1. Remove the oil level indicator and oil level
indicator tube upper retaining bolt.
2. Remove the clutch disc and pressure plate.
For additional information, refer to: Clutch
Disc and Pressure Plate
(308-01 Clutch,
Removal and Installation).
3. Drain the engine.
Allow the oil to drain into a suitable container.
4. N0TE:lnspect the oil pan drain plug seal for
damage. Install a new drain plug and seal
if
required.
6. Using the special tool, lock the flywheel in
position.
7. Remove the flywheel.
2006.0 Fiesta 1212006 G451307en
procarmanuals.com

303-01 B-58 Engine - 2.OL Duratec-HE (M14) 303-01 B-58
IN-VEHICLE REPAIR
Discard the installation sleeve. Install the oil pan.
2. Clean the mating faces oft he cylinder blocks 6. Install the engine front cover lower retaining the oil pan and the engine front cover with
bolts.
cleaner.
3. Apply a 3 mm bead of sealant to the oil pan.
7. Tighten the oil pan retaining bolts in the
sequence shown.
4. N0TE:lnstall the oil pan within 10 minutes
of applying the silicone sealant and tighten
the retaining bolts within
a further 5 minutes.
Apply a
3 mm bead of sealant to the oil pan.
5. N0TE:Do not tighten the retaining bolts at
this stage.
8. N0TE:lnstall new flywheel retaining bolts.
N0TE:Do not tighten the flywheel retaining bolts
at this stage.
2006.0 Fiesta 1212006 G451307en
procarmanuals.com

303-01 B-60 Engine - 2.OL Duratec-HE (M14) 303-01 B-60
IN-VEHICLE REPAIR
Engine Front Cover(21 148 0)
f'
General Equipment 6. Detach the coolant expansion tank and lay
I Vehicle jack it to one side.
Materials Name Specification
I Silicone Sealant I WSE-M4G323-A4 I
Removal
1. Remove the crankshaft belt pulley.
For additional information, refer to:
Crankshaft Pulley (303-01 Engine
- 2.OL
Duratec-HE (M14), Invehicle Repair).
2. Remove the timing cover lower bolts.
7. Support the engine with
a vehicle jack.
8. Remove the front engine mount.
Discard the front engine mount nuts.
3. Disconnect the crankshaft position (CKP)
sensor electrical connector.
4. Lower the vehicle.
5. Remove the power steering pump.
For additional information, refer to: Power
Steering Pump
- 2.OL Duratec-HE (M14)
(211 -02 Power Steering, Removal and
Installation).
9. Remove the coolant pump pulley.
2006.0 Fiesta 121~0o6 G451289en
procarmanuals.com

303-01 B-61 Engine - 2.OL Duratec-HE (M14) 303-01 B-61
IN-VEHICLE REPAIR
10. Remove the drive belt idler pulley.
11. Remove the timing cover upper bolts.
Remove the timing cover.
Apply sealer to the timing cover (bead
diameter:
3 mm).
3. Install the timing cover (engine shown
installation removed for clarity).
Tighten the bolts in the sequence shown.
1. Clean the sealing surfaces of the timing Tighten bolts I to 8 to a torque of 10 Nm.
cover and the cylinder block. Tighten bolt 9 to 48 Nm.
2. N0TE:lnstall the timing cover within 10 Tighten bolts 10 to 19 to a torque of 10 Nm.
minutes of applying the silicon sealer.
2006.0 Fiesta 12/2006 G451289en
procarmanuals.com

303-01 B-63 Engine - 2.OL Duratec-HE (M14) 303-01 B-63
IN-VEHICLE REPAIR
9. Connect the CKP sensor electrical
. connector.
10. Install the crankshaft belt pulley.
For additional information, refer to: Crankshaft Pulley (303-01 Engine
- 2.OL
Duratec-HE (M14), In-vehicle Repair).
2006.0 Fiesta 1212006 G451289en
procarmanuals.com

303-01 B-69 Engine - 2.OL Duratec-HE (M14) 303-01 B-69
IN-VEHICLE REPAIR
Cylinder Head(21 163 0)
Special Tool(s) 5. Remove the timing chain.
I Materials I
24003
I I Name Specification
Remover/lnstaller, Hose
Clamp
303-397
Removal
For additional information, refer to: Timing
Chain (303-01 Engine
- 2.OL Duratec-HE
(M14), Invehicle Repair).
6. Disconnect the exhaust gas recirculation
(EGR) valve electrical connector.
Hypoid Gear Oil
A WARNING:Do not smoke or carry lighted
tobacco or open flame of any type when
working on or near any fuel related
components. Highly flammable vapors are
always present and may ignite. Failure to
7. Using the special tool, disconnect the
follow these instructions may result in coolant hose
from the EGR valve.
personal injury.
/
SQM-2C9002-AA
( I. Drain the cooling system.
For additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling
- 2.OL Duratec-HE
(M14), General Procedures).
2. Remove the exhaust manifold support
bracket retaining bolts.
3. Lower the vehicle.
4. Remove the intake manifold.
For additional information, refer to: Intake
Manifold (303-01 Engine
- 2.OL Duratec-HE
(M14), In-vehicle Repair).
8. Using the special tool, disconnect the
coolant hoses from the coolant outlet
connector.
2006.0 Fiesta 1212006 G451308en
procarmanuals.com

303-01 B-70 Engine - 2.OL Duratec-HE (M14) 303-01 B-70
IN-VEHICLE REPAIR
9. Disconnect the engine coolant temperature 12. Remove the exhaust manifold upper heat
(ECT) sensor electrical connector.
shield (engine shown removed for clarity).
('
10. Remove the power steering pump return 13. Remove the exhaust manifold lower heat
line support bracket.
shield (engine shown removed for clarity).
11. Remove the generator upper retaining bolt. 14. Remove the exhaust manifold retaining
nuts (engine shown removed for clarity).
Detach the exhaust manifold from the
cylinder head and position it to one side.
Discard the gasket and nuts.
15. CAUTIONS: c
n~ee~ the camshaft bearing caps and the
camshafts in order for installation.
2006.0 Fiesta 12/2006 G451308en
procarmanuals.com

303-01 B-72 Engine - 2.OL Duratec-HE (M14) 303-01 B-72
IN-VEHICLE REPAIR
Check the valve clearance and adjust if 9. Using the special tool, connect the coolant
necessary. hose to the EGR valve.
/
For additional information, refer to: Valve
Clearance Adjustment
(303-01 Engine - 2.OL
Duratec-HE (M14), General Procedures).
6. Connect the engine coolant temperature
(ECT) sensor electrical connector.
7. Using the special tool, connect the coolant
hoses to the coolant outlet connector.
8. Connect the exhaust gas recirculation (EGR)
valve electrical connector. 10.
N0TE:lnstall a
new exhaust manifold gasket
and nuts.
Tighten the exhaust manifold retaining nuts
(engine shown removed for clarity).
11. Install the exhaust manifold lower heat
shield (engine shown removed for clarity).
2006.0 Fiesta 1212006 G451308en
procarmanuals.com