air con FORD FIESTA 2007 Workshop Manual

303-01 B-20 Engine - 2.OL Duratec-HE (M14) 303-01 B-20
GENERAL PROCEDURES
28. Install the air cleaner.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (303-12
Intake Air Distribution and Filtering,
Removal and Installation).
29. Connect the battery ground cable.
For additional information, refer to: Battery
Disconnect
(414-01 Battery, Mounting and
Cables, General Procedures).
- --
2006.0 Fiesta 1212006 G451279en
procarmanuals.com

303-01 B-21 Engine - 2.OL Duratec-HE (M14) 303-01 B-21
IN-VEHICLE REPAIR
Intake Manifold(21 183 0)
Removal
1. Disconnect the battery.
For additional information, refer to: Battery
Disconnect (414-01 Battery, Mounting and
Cables, General Procedures).
2. Remove the air cleaner.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (303-12
lntake Air Distribution and Filtering,
Removal and Installation).
3. Remove the right-hand headlamp.
6. Disconnect the generator electrical
connectors.
For additional information, refer to:
Headlamp Assembly (41 7-01 Exterior
Lighting, Removal and Installation). 7.
Remove the intake manifold lower retaining
4. Raise and support the vehicle. For additional bolt.
information, refer to: (I
00-02 Jacking and
Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
( 5. Disconnect the crankshaft position (CKP)
sensor electrical connector.
8. Remove the oil level indicator tube lower
retaining bolt.
2006.0 Fiesta 1212006 G451284en
procarmanuals.com

303-01 8-22 Engine - 2.OL Duratec-HE (M14) 303-01 B-22
IN-VEHICLE REPAIR
9. Detach the wiring harness from the intake
13. Remove the fuel rail.
manifold. For additional information, refer to: Fuel
Rail (303-04 Fuel Charging and Controls
- 2.OL Duratec-HE (M14), Removal and
Installation).
14. Detach the starter motor electrical
connector from the intake manifold.
10. Detach the power steering supply line from
the intake manifold.
15. Disconnect the manifold absolute pressure
(MAP) sensor electrical connector.
,.
.. 1
11. Lower the vehicle.
12. Detach the engine wiring harness from the
valve cover.
1. Unlcip the power steering return line from the
wiring harness bracket.
2. Remove the air cleaner retaining bracket.
16. Detach the evaporative emission valve
3. Unclip the engine wiring harness bracket (EVAP) hose from the intake manifold.
from the intake manifold.
4. Unclip the engine wiring harness from the
intake manifold.
2006.0 Fiesta 12/2006 G451284en
procarmanuals.com

303-01 B-23 Engine - 2.OL Duratec-HE (M14) 303-01 B-23
IN-VEHICLE REPAIR
17. Disconnect the intake manifold runner 20. Disconnect the hood latch electrical
control (IMRC) electrical connector. connector.
18. Disconnect the throttle body electrical 21. Remove the hood latch lever retaining bolt.
connector.
22. Detach the hood latch from the radiator
19. Disconnect the knock sensor (KS) electrical grille
opening panel reinforcement.
connector (power steering fluid reservoir
shown removed for clarity).
Detach the KS electrical connector from the
intake manifold.
2006.0 Fiesta 1212006 G451284en
procarmanuals.com

303-01 B-24 Engine - 2.OL Duratec-HE (M14) 303-01 B-24
IN-VEHICLE REPAIR
23. Disconnect the brake booster vacuum line
26. Disconnect the positive crankshaft
from the intake manifold.
ventilation
(PCV) hose from the intake
manifold.
24. Remove the oil level indicator and oil level
indicator tube.
27. Remove the intake manifold.
Installation
1. N0TE:lnstall new gaskets if necessary.
To install, reverse the removal procedure.
25. Remove the intake manifold retaining bolts
(engine shown removed for clarity).
Detach the intake manifold from the cylinder
head.
2006.0 Fiesta 12/2006 G451284en
procarmanuals.com

303-01 B-26 Engine - 2.OL Duratec-HE (M14) 303-01 B-26
IN-VEHICLE REPAIR
Crankshaft Pulley(21 572 0)
Special Tool(s)
I I Flange Holding Wrench, I
Universal
205-072
Adapter for 205-072
205-072-02
Alignment Tool, Camshaft
Alignment
303-376
Timing Peg, Crankshaft TDC
position
303-507
I I Pliers, Valve Stem Seal
General Equipment
I Bolt M6 x 18 mm I
Materials
Name
S~ecification
I Silicone sealant I WSE-M4G323-A4 I
Removal
I. Disconnect the battery.
For additional information, refer to: Battery
Disconnect (414-01 Battery, Mounting and
Cables, General Procedures).
2. Remove the air cleaner.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (303-12
Intake Air Distribution and Filtering,
Removal and Installation).
3. Detach the engine wiring harness from the
valve cover.
1. Unclip the power steering fluid return line
from the retaining clips.
2. Remove the air cleaner retainer.
3. Unclip the engine wiring harness bracket at
the intake pipe.
4. Unclip the engine wiring harness at the intake
pipe.
2006.0 Fiesta 1212006 G451288en
procarmanuals.com

303-01 B-27 Engine - 2.OL Duratec-HE (M14) 303-01 B-27
IN-VEHICLE REPAIR
4. Detach the positive crankcase ventilation 7. Remove the EVAP valve bracket.
(PCV) hose from the valve cover.
8. Using the special tool, disconnect the spark
5. Disconnect the camshaft position sensor plug electrical
connectors.
(CMP sensor) electrical connector.
6. Remove the air cleaner retainer.
9. Using the special tool, remove the spark
plugs.
2006.0 Fiesta 1212006 G451288en
procarmanuals.com

303-01 B-28 Engine - 2.OL Duratec-HE (M14) 303-01 B-28
IN-VEHICLE REPAIR
10. Remove the valve cover.
11. Remove the drive belt.
For additional information, refer to:
Accessory Drive Belt
- 2.OL Duratec-HE
(M14) (303-05 Accessory Drive, Removal
and Installation).
12.
N0TE:Only rotate the crankshaft in the
normal direction of rotation.
Rotate the crankshaft until piston no.
1 is
approx. 45 degrees before TDC. Using
the special tool, remove the crankshaft
pulley.
14. Remove the crankshaft front seal.
For additional information, refer to:
Crankshaft Front Seal (303-01 Engine
-
2.OL Duratec-HE (M14), Invehicle Repair).
15. Remove the front friction washer (engine
shown removed for clarity).
. Discard the friction washer.
16. N0TE:Do not damage the inner constant
13.
N0TE:Do not discard the crankshaft pulley velocity
(CV) joint boot.
bolt. Pull the inner CV joint boot off the
intermediate shaft.
2006.0 Fiesta 1212006 G451288en
procarmanuals.com

303-01 B-29 Engine - 2.OL Duratec-HE (M14) 303-01 B-29
IN-VEHICLE REPAIR
Remove and discard the CV joint boot clamp. 5. Install the special tool.
Installation 6. Raise the vehicle. For additional information,
refer to: (1 00-02 Jacking and Lifting)
1. N0TE:lnstall a new front friction washer.
Jacking (Description and Operation),
Install the front friction washer (engine
Lifting (Description and Operation).
shown removed for clarity).
7. Remove the cylinder block lower blanking
plug and install the special tool.
2. Install the crankshaft front seal.
For additional information, refer to:
8. N0TE:Only rotate the crankshaft in the
Crankshaft Front Seal (303-01 Engine - 2.OL normal direction of rotation.
Duratec-HE (M14), In-vehicle Repair).
Rotate the crankshaft using the crankshaft
3. Lower the vehicle.
pulley bolt until the crankshaft contacts the
4. N0TE:Only rotate the camshafts in the special
tool.
normal direction of rotation.
Carefully rotate the camshafts using a
spanner until the cams of cylinder no. 4 are
positioned at the valve overlap.
2006.0 Fiesta 1212006
procarmanuals.com

303-01 B-32 Engine - 2.OL Duratec-HE (M14) 303-01 B-32
IN-VEHICLE REPAIR
24. Raise the vehicle. For additional N0TE:Make sure that the contact surface for the
information, refer to: (100-02 Jacking and CV joint boot on the intermediate shaft is clean. ,
Lifting)
Slide the inner CV joint boot onto the
Jacking (Description and Operation),
intermediate shaft. (..
Lifting (Description and Operation). Use a suitable screwdriver under the boot to
25. Remove the M6 x 18 mm bolt. allow air to escape.
26. Remove the special tool. 29. N0TE:lnstall a
new boot clamp.
Using a suitable grip wrench, install the inner
CV joint boot clamp.
27. Install the cylinder block lower blanking
plug.
30. N0TE:When installing a new engine front
cover, the crankshaft position sensor
(CKP
sensor) must be aligned using the tool
supplied.
28.
N0TE:Do not damage the boot of the inner
CV joint. Align
the
CKP sensor (engine shown
removed for clarity).
1. Loosen the CKP sensor bolts.
2006.0 Fiesta 1212006 G451288en
procarmanuals.com