air con FORD FIESTA 2007 Workshop Manual

303-03B-26 Engine Cooling - 2.OL Duratec-HE (M14) 303-03B-26
REMOVAL AND INSTALLATION
Removal 2. Push the cooling fan motor and shroud l.
upwards and then downwards to remove.
1. Disconnect the battery ground cable. I
For additional information, refer to: Battery
Disconnect
(414-01 Battery, Mounting and
Cables, General Procedures).
2. Drain the cooling system.
For additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling - 2.OL Duratec-HE
(M14), General Procedures).
3. Disconnect the cooling fan motor and
cooling fan resistor electrical connectors.
4. Remove
the air cleaner intake pipe resonator.
5. Remove the cooling fan motor and shroud.
1. Release the cooling fan motor and shroud
from the retaining brackets.
6. Disconnect the radiator upper hose.
1. Pull out the quick release spring clip.
2. Pull the radiator upper hose from the quick
release connector.
7. Disconnect the radiator degas hose from the
radiator.
Release the locking tangs.
8. Remove the radiator retainers.
2006.0 Fiesta 1212006 G457934en
procarmanuals.com

303-03B-27 Engine Cooling - 2.OL Duratec-HE (M14) 303-03B-27
REMOVAL AND INSTALLATION
I. Remove the radiator retainer locking screws.
2. Remove the radiator retainers and grommets.
9. Detach the radiator and the air conditioning
(NC) condenser from the support panel.
Om ACAUTION:S~~~~~~ the AIC condenser
by positioning it on the support panel.
Slide the
NC condenser to detach it from the
radiator
, 11. Remove the radiator. I
Installation
I. To install, reverse the removal procedure.
2006.0 Fiesta 1212006 G457934en
procarmanuals.com

Fuel Charging and Controls - 1.25L
Duratec-1 6V (Sigma)llI4L Duratec-1 6V
(Sigma)ll .6L Duratec-1 6V (Sigma)
SPECIFICATIONS
General Specifications
I Maximum idle increase for high generator load I I00 rpm I
Condition
Regulated fuel pressure
l~ir conditioning idle upspeed at low ambient temperatures I 100 rpm I
Specification
380 kpa (55 psi)
I Air conditioning idle upspeed at high ambient temperatures I 150 rpm I
I Power steering idle speed upspeed I 50 rpm I
Toraue S~ecifications
Description Nm I b-ft Ib-in
I Throttle body retaining bolts I 10 1 - I 89 I
I Fuel pressure regulator retaining bolts I 10 I - I 89 I
I Fuel injection supply manifold retaining bolts I 15 I 11 I - I
2006.0 Fiesta 1212006 GI 46265en
procarmanuals.com

Fuel Charging and Controls - 1.25L
Duratec-1 6V (Sigma)ll.4L Duratec-I 6V
303-04A-4 (Sigma)ll.GL Duratec-1 6V (Sigma) 303-04A-4
REMOVAL AND INSTALLATION
Throttle Body(23 198 0)
Removal 2. N0TE:Do not press the accelerator pedal
during the initialization period as this will
1. Disconnect the air cleaner outlet pipe from
prevent the complete initialization of the
the throttle body. throttle body.
2. Remove the throttle body retaining bolts. Turn
the ignition key to position
II and wait
for one minute to
initialize the throttle body.
3. Turn the ignition key to the OFF position.
3. Disconnect the throttle body electrical
connector and remove the throttle body.
I nin
1. To install, reverse the removal procedure.
2006.0 Fiesta 1212006 GI 46266en
procarmanuals.com

Fuel Charging and Controls - 1.25L
Duratec-1 6V (Sigma)llI4L Duratec-1 6V
(Sigma)llI6L Duratec-1 6V (Sigma)
REMOVAL AND INSTALLATION
Fuel Charging Wiring Harness(36 437 0)
Removal
1. Remove the air cleaner. For additional
5. N0TE:lt is necessary to lift the red locking
tab before the electrical connector can be
disconnected.
information, refer to Section
303-12 [Intake the throttle body electrical Air Distribution and Filtering].
connector.
2. Disconnect the spark plug wires from the
ignition coil.
6. Disconnect the fuel charging wiring harness
electrical connector.
3. Disconnect the engine coolant temperature
(ECT) sensor electrical connector.
(
7. Remove the positive crankcase ventilation
(PCV) hose.
4. Disconnect the camshaft position (CMP)
sensor electrical connector.
2006.0 Fiesta 1212006 GI 89082en
procarmanuals.com

Fuel Charging and Controls - 1.25L
Duratec-1 6V (Sigma)llI4L Duratec-1 6V
303-04A-7 (Sigma)llI6L Duratec-1 6V (Sigma) 303-04A-7
REMOVAL AND INSTALLATION
Fuel Injection Supply Manifold(23 450 0)
Removal
WARNINGS:
A Do not smoke or carry lighted tobacco or
open flame of any type when working on
or near any fuel related components.
Highly flammable vapors are always
present and can ignite. Failure to follow
these instructions may result in personal
injury.
A This procedure involves fuel handling. Be
prepared for fuel spillage at all times and
always observe fuel handling precautions.
Failure to follow these instructions may
result in personal injury.
5. Disconnect the fuel injector electrical
connectors and position the wiring harness
to one side.
1. Release the fuei system pressure. For
additional information, refer to 6. Disconnect the vacuum line from the fuel
Section
31 0-00 [Fuel System - General pressure
regulator.
Information].
2. Disconnect the battery ground cable. For
additional information, refer to
Section
414-01 [Battery, Mounting and
Cables].
3. Remove the air cleaner. For additional
information, refer to Section
303-12 [Intake
Air Distribution and Filtering].
4. Remove the positive crankcase ventilation
(PCV) hose.
7. N0TE:Fuel supply line connectors are white
or are identified by a white band. Fuel return
line connectors are red or are identified by
a red band.
2006.0 Fiesta 1212006 GI 89083en
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-04B-8 Duratec-HE (M14) 303-04B-8
DIAGNOSIS AND TESTING
lntake manifold
item Description
I 1 I Intake manifold tuning (IMT) swirl plates I Inspection and Verification
121
lntake manifold runner control (IMRC)
throttle plates
The intake manifold for both Ethanol
E85 and
standard unleaded fueled vehicles is the same
construction.
Built into the intake manifold, are the
IMRC throttle
plates and IMT swirl plates.
Under low demand throttle conditions, the air
charge is delivered to the cylinder head intake ports
through the primary air intake chambers. The clean
flow of the air charge is disturbed by the IMT swirl
plates to assist in the mixing of the air fuel mixture
at the fuel injectors.
1. Verify the customer concern.
2. Visually inspect for obvious signs of mechanical
or electrical damage.
Visual lnspection Chart
I Mechanical I Electrical I
- Fuel leak(s)
- Vacuum line(s)
- Gasket(s)
- Seal(s)
- Fuel injector(s)
- Throttle body
- Fuel rail
- Powertrain control
module (PCM)
- Wiring harness
- Electrical
connector(s)
- Throttle body
- Fuel injector(s)
2006.0 Fiesta 1212006 GI 65371en
During high demand throttle conditions, the IMRC
throttle plates are opened and the air charge is - Fuel supply line
allowed to use both primary and secondary intake
chambers. This means a higher volume of air 3. If an obvious cause for an observed or reported
charge can be accommodated by the intake concern
is found, correct the cause (if
possible) (
before proceeding to the next step. \. . manifold. During this high demand throttle
condition, the IMT swirl plates are fully open so as
4. If the cause is not visually evident, verify the
not to restrict the air charge flow.
symptom and refer to the Symptom Chart.
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-048-1 0 Duratec-HE (M14) 303-04B-10
DIAGNOSIS AND TESTING
Symptom Possible Sources Action
Fuel rail fuel pressure sensor. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
Fuel injectors. INSPECT
the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
I Incorrect valve timing. I CHECK the valve timing. I
Poor starting
Low cylinder compression.
Low fuel system pressure.
TEST the cylinder compres-
sion.
Check the fuel system pres-
sure.
REFER to: Fuel System Pres-
sure Check (31
0-OOA,
General Procedures).
Fuel system leak. CHECK the system for fuel
leak(s). REPAIR the system as
necessary.
Fuel system restriction. INSPECT the
fuel system.
INSTALL new components as
necessary. TEST the system
for normal operation.
I Fuel filter blocked. I INSTALL a new fuel filter. I
lncorrect engine oil.
Air
cleaner element blocked.
INSTALL a new engine oil filter
and engine oil.
INSTALL a new air cleaner
element.
lncorrect power steering fluid. DRAIN and REFILL the
power
steering system with the correct
fluid.
REFER to: Power Steering
System Flushing
- Vehicles
With: Electro-Hydraulic Power
Steering (EHPS) (21 1-00,
General Procedures).
2006.0 Fiesta 1212006 GI 65371 en
CKP sensor.
Engine coolant temperature
(ECT) sensor. Carry out a
full engine
diagnosis using the guided
diagnostic menu in WDS.
Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-04B-1 I Duratec-HE (M14) 303-04B-11
DIAGNOSIS AND TESTING
Symptom Possible Sources
Action
Fuel injector(s). INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
Fuel rail fuel pressure sensor. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
Catalytic converter blocked. REMOVE and visually
INSPECT the catalytic
converter as necessary.
REFER to: Catalytic Converter
- 1.8L Duratec-HE (M14)/2.OL
Duratec-HE (M14) (309-00,
Removal and Installation).
Low cylinder compression. TEST the engine cylinder
compression.
Engine starts but immediately
stops Air cleaner element blocked. INSTALL
a new air cleaner
element.
CKP sensor.
Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
CMP sensor. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
PCM. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
Low fuel system pressure.
Check the fuel system pres-
sure.
REFER to: Fuel System Pres-
sure Check (31
0-OOA,
General Procedures).
Fuel system
restriction
I
--
INSPECT the fuel system.
INSTALL new components as
necessary. TEST the system
for normal operation.
I Fuel filter blocked. I INSTALL a new fuel filter. I
Poor idling Air cleaner
element blocked. INSTALL a new air cleaner
element.
2006.0 Fiesta 1212006 GI 65371 en
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-04B-13 Duratec-HE (M14) 303-04B-13
DIAGNOSIS AND TESTING
Possible Sources Action
,
Engine ignition.
Symptom
Engine stumbling
Engine lacks power
REFER to: Engine lgnition
(303-07B, Diagnosis and
Testing).
Fuel injectors.
INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
Low fuel system pressure.
EGR valve sticking open.
Check the fuel system pres-
sure.
REFER to: Fuel System Pres-
sure Check (31
0-OOA,
General Procedures).
Fuel rail fuel pressure sensor.
REFER to: Engine Emission
Control (303-08 Engine
Emission Control
- 2.OL
Duratec-HE (M14), Diagnosis
and Testing).
Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
Engine ignition. REFER to: Engine lgnition
(303-07B, Diagnosis and
Testing).
Brakes binding.
I CHECK the braking system.
REFER to: Brake System (206-
1 00, Diagnosis and Testing).
Vehicle overloaded, or
excessive wind resistance (roof
racks, towing etc). ADVISE
the customer about
the effects of overloading the
vehicle and wind resistance on
the fuel consumption.
Air cleaner element blocked.
REFER to: Fuel System Pres-
sure Check (31
0-OOA,
General Procedures).
INSTALL a new air cleaner
element as necessary.
Low fuel system pressure.
r
Check the fuel system pres-
sure.
2006.0 Fiesta 1212006 GI 65371 en
Kinked or restricted fuel lines. INSPECT the fuel lines.
INSTALL new components as
necessary. TEST the system
for normal operation.
procarmanuals.com