power steering fluid FORD FIESTA 2007 Service Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 2007, Model line: FIESTA, Model: FORD FIESTA 2007Pages: 1226, PDF Size: 61.26 MB
Page 371 of 1226

21 1 -02123 Power Steering 21 I -02-23
REMOVAL AND INSTALLATION
11. Fill and bleed the power steering system. Procedures),
For additional information, refer to: (211 -00 Power Steering System
Bleeding (General
Steering System - General Information) Procedures).
Power Steering System Filling (General
Removal Details
ltem 1 Power steering pump pulley
1. Using the special tool, remove the power
steering pump pulley.
I ' 2. CAUTIONS: /,
Acap the power steering pump outlet port
to prevent fluid loss or dirt ingress.
hap the power steering pump to steering
gear pressure line to prevent fluid loss or
dirt ingress.
Item 4 Power steering pump to steering gear
pressure line bracket to intake manifold retaining
bolt
1. Raise and support the vehicle. For additional
information, refer to: (1 00-02 Jacking and
Lifting)
Jacking (Description and Operation),
Jacking (Description and Operation).
2. Detach the power steering pump to steering
gear pressure line from the intake manifold.
Disconnect the power steering pump to
Item 5 Power steering pump to steering gear
steering gear pressure line from the power
pressure line steering pump. 1. Remove the front wheels and tires. Remove and discard the power steering
pump to steering gear pressure line union
For additional information, refer to: Wheel
O-ring seal. and Tire (204-04 Wheels and Tires, Removal
and Installation).
2006.0 Fiesta 1212006 G458165en
procarmanuals.com
Page 373 of 1226

21 1 -02-25 Power Steering 21 1 -02-25
REMOVAL AND INSTALLATION
Remove the exhaust hanger insulator. 11. Remove the front axle crossmember
retaining bolts on both sides.
8. N0TE:Use a 5 mm Allen key to prevent the
stabilizer bar link ball joint from rotating.
12. Lower the front axle crossmember
Detach the stabilizer bar link from the approximately
100 mm.
stabilizer bar on both sides.
13. Detach the steering gear to power steering
fluid reservoir return line from the power
steering pump to steering gear pressure
line.
9. Remove the engine support insulator.
10. Using a transmission jack and a wooden
block, support the front axle crossmember.
14' ~CAUTION:C~~ the steering gear valve
body inlet port and outlet port to prevent
fluid loss or dirt ingress.
Disconnect the power steering lines from the
steering gear valve body.
1. Remove the power steering lines clamp plate
retaining bolt.
2. Rotate the power steering lines clamp plate.
2006.0 Fiesta 1212006 G458165en
procarmanuals.com
Page 374 of 1226

21 1-02-26 Power Steering 21 1-02-26
REMOVAL AND INSTALLATION
Allow the power steering fluid to drain into a 15. Remove and discard the power steering
container. lines O-ring seals.
Installation Details
Item 5 Power steering pump to steering gear
pressure line 3.
Attach the steering gear to power steering
fluid reservoir return line to the power
1. Install new power steering lines O-ring seals.
steering pump to steering gear pressure line.
2. Connect the power steering lines to the 4. N0TE:Use the front axle crossmember rear
steering gear valve body.
inner retaining bolts to locate the special
1. Rotate the power steering lines clamp plate. tool.
2. Install the power steering lines clamp plate N0TE:Do not fully tighten the front axle
retaining bolt. crossmember rear inner retaining bolts at this
-
stage.
- - - - - - -- -
2006.0 Fiesta 1212006 G458165en
procarmanuals.com
Page 378 of 1226

21 1 -02-30 Power Steering 21 1 -02-30
REMOVAL AND INSTALLATION
Steering Gear to Power Steering Fluid Reservoir Return Line -
2.OL Duratec-HE (M14) RHD (' ,
Centralize the steering and lock it in position. table(s).
Special Tool(s)
2006.0 Fiesta 1212006 G458167en
2. Detach the steering column shaft from the
steering gear pinion.
Discard the steering column shaft to steering
gear pinion retaining bolt.
Pp
205524
24003
Alignment Pins, Subframe
205-524
Removerllnstaller, Hose
Clamp
303-397
General Equipment
Transmission jack 3. Remove the front wheels and tires.
Materials For
additional information, refer to: Wheel
and Tire (204-04 Wheels and Tires, Removal
Name Specification and Installation).
4. Lower the vehicle.
Grease
1. N0TE:Make sure that the road wheels are in 5. Remove the components in the order
the straight ahead position.
indicated in the following illustration(s) and
SA-M 1 C9107-A
procarmanuals.com
Page 379 of 1226

211 -02-31 Power Steering 211-02-31
REMOVAL AND INSTALLATION
Item Description
1 Steering gear to power steering fluid
reservoir return line upper retaining clip
See Removal Detail
2 Steering gear to power steering fluid
reservoir return line support bracket to
generator retaining nut
See Removal Detail
3
I I steering gear retaining bolt I
Item Description
Steering gear heat shield
See Removal Detail
See Installation Detail
4 Steering gear to power steering fluid
reservoir return line support bracket to
5
6. To install, reverse the removal procedure.
Cable
ties
See Removal Detail
See Installation Detail
6
2006.0 Fiesta 1212006 G458167en
Steering gear to power steering fluid
reservoir return line
See Removal Detail
See Installation Detail
procarmanuals.com
Page 380 of 1226

21 1 -02-32 Power Steering 21 1-02-32
REMOVAL AND INSTALLATION
7. Fill and bleed the power steering system. For Procedures),
additional information, refer to: (211-00 Power Steering System Bleeding (General
Steering System
- General Information) Procedures). ( ;)
Power Steering System Filling (General
Removal Details
Item 1 Steering gear to power steering fluid
reservoir return line upper retaining clip
1. CAUTIONS:
&ap the steering gear to power steering
fluid reservoir return line to prevent fluid loss
or dirt ingress.
hap the power steering fluid reservoir to
prevent fluid loss or dirt ingress.
Using the special tool, disconnect the
steering gear to power steering fluid
reservoir return line from the power steering
fluid reservoir.
Allow the power steering fluid to drain into a
container.
Item 2 Steering gear to power steering fluid
reservoir return line support bracket to generator
retaining nut
I. N0TE:Note the position of the steering gear
to power steering fluid reservoir return line
support bracket to aid installation.
Detach the generator wiring harness from
the steering gear to power steering fluid
reservoir return line support bracket.
Item 3 Steering gear heat shield
I. Raise and support the vehicle. For additional
information, refer to: (1 00-02 Jacking and
Lifting)
Jacking (Description and Operation),
2. Detach the steering gear to power steering Lifting
(Description and Operation).
fluid reservoir return line from the generator 2.
Detach the steering gear heat shield from
-
wiring harness shield. the
steering gear.
2006.0 Fiesta 1212006 G458167en
procarmanuals.com
Page 382 of 1226

21 1 -02-34 Power Steering 2 1 1 -02-34
REMOVAL AND INSTALLATION
7. Remove the front axle crossmember
retaining bolts on both sides.
8. Lower the front axle crossmember
approximately
I00 mm. Disconnect
the power steering lines from the
steering gear valve body.
1 . Remove the power steering lines clamp plate
retaining bolt.
2. Rotate the power steering lines clamp plate.
Allow the power steering fluid to drain into a
container.
9. Detach the steering gear to power steering
fluid reservoir return line from the power
steering pump to steering gear pressure line.
2. Remove and discard the power steering lines
O-ring seals.
Item 6 steering gear to power steering fluid
reservoir return line
&AUTION:C~~ the steering gear valve
body inlet port and outlet port to prevent
fluid loss or dirt ingress.
Installation Details
-- ----
2006.0 Fiesta 12/2006 G458167en
procarmanuals.com
Page 383 of 1226

21 1-02-35 Power Steering 21 1-02-35
REMOVAL AND INSTALLATION
Item 6 Steering gear to power steering fluid 2. N0TE:Use the front axle crossmember rear
reservoir return line inner
retaining bolts to locate the special
I tools. I, Install new O-ring seals onto the power
steering lines.
N0TE:Do not fully tighten the front axle
crossmember rear inner retaining bolts at this
stage.
Using a transmission jack, wooden block
and the special tools, position and align the
front axle crossmember.
2. Connect the power steering lines to the
steering gear valve body.
1. Rotate the power steering lines clamp plate.
2. Install the power steering lines clamp plate
retaining bolt.
3a &AUTION:W~~I~ tightening the front axle
crossmember front retaining bolts and the
i front axle crossmem ber rear outer retaining
bolts, make sure that the front axle
crossmember does not move.
Ifem 5 Cable ties
1. Attach the steering gear to power steering
fluid reservoir return line to the power
steering pump to steering gear pressure line. Install
the front axle crossmember front
retaining bolts and the front axle
crossmember rear outer retaining bolts on
both sides.
2006.0 Fiesta 1212006 G458167en
procarmanuals.com
Page 386 of 1226

21 1 -02-38 Power Steering 21 1 -02-38
REMOVAL AND INSTALLATION
Steering Gear(l3 11 6 0)
I I Separator, Ball Joint Discard
the retaining bolt.
3. Remove the wheels and tires.
I I I For additional information, refer to: Wheel I I I
General Equipment I I
and Tire (204-04 Wheels and Tires, Removal
and Installation).
Removal
All vehicles
Transmission jack 1 4. Disconnect the power steering fluid reservoir
I. N0TE:Make sure that the road wheels are in
the straight ahead position.
Materials
Centralize the steering and lock
it in position. return
hose quick release coupling.
2. Detach the steering column shaft from the
steering gear pinion.
return hose quick release coupling.
Allow the fluid to drain into a suitable
container.
Name Specification 1. Press the power steering fluid reservoir return
5m &AUTION:O~~~ bending of the exhaust
flexible pipe may cause damage resulting in
failure.
2006.0 Fiesta 1212006 GI 05648en
hose quick release coupling locking tangs.
Grease
2. Disconnect the power steering fluid reservoir ( SA-M 1 C9107-A
procarmanuals.com
Page 389 of 1226

211 -02-41 Power Steering 21 1-02-41
REMOVAL AND INSTALLATION
15. Detach the power steering lines from the 19. Lower the front axle crossmember to gain
steering gear (left-hand drive shown). access
to the steering gear.
i 20. Remove the steering gear.
16. Disconnect the power steering lines from
the steering gear valve body.
1. Remove the retaining bolt.
2. Rotate the clamp plate.
Allow the fluid to drain into a suitable
container.
Discard the O-ring seals.
17.
Using a transmission jack and a wooden
block, support the front axle crossmember.
18. Remove the front axle crossmember
retaining bolts on both sides.
21. Remove and discard the steering gear
bulkhead floor seal.
22. Remove the exhaust heat shield.
2006.0 Fiesta 1212006 GI 05648en
procarmanuals.com