automatic transmission FORD MUSTANG 2003 Workshop Manual

GENERAL PROCEDURES
Cable Adjustment
1. NOTE: Make sure that the range selector lever is tight against the rearward overdrive stop.
Place the transmission range selector lever in the overdrive position.
2. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
3. Loosen the manual control lever nut.
4. Place the transmission manual control lever in the overdrive position.
5. Tighten the nut on the manual control lever.
SECTION 307-
05: Automatic Transaxle/Transmission External Controls 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Brake Shift Interlock Actuator
Removal
1. Remove the shifter top control panel.
2. Disconnect the electrical connectors.
3. Remove the shifter bezel. 4. Remove the bulb from the bezel. SECTION 307-
05: Automatic Transaxle/Transmission External Controls 2003 Mustang Workshop Manual Klj . 1 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Cable and Bracket
Removal
1. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
2. Remove the cable shift from the shifter lever and bracket and discard the clip.
3. Remove the bolt from the cable.
4. Remove the bolt from the cable.
5. Disconnect the transmission range selector lever cable from the TR sensor lever.
SECTION 307-
05: Automatic Transaxle/Transmission External Controls 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Selector Lever
Removal
1. Remove the shifter top control panel.
2. Disconnect the electrical connectors.
3. Remove the shifter bezel. 4. Remove the bulb from the bezel. SECTION 307-
05: Automatic Transaxle/Transmission External Controls 2003 Mustang Workshop Manual Klj . 1 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Transmission Control Switch
Removal
1. Remove the shifter top control panel.
2. Disconnect the electrical connectors.
3. Remove the shifter bezel. 4. Remove the bulb from the bezel. SECTION 307-
05: Automatic Transaxle/Transmission External Controls 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Bezel
Removal
1. Remove the shifter top control panel.
2. Disconnect the electrical connectors.
3. Remove the shifter bezel. 4. Remove the bulb from the bezel. SECTION 307-
05: Automatic Transaxle/Transmission External Controls 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Bulb
Removal and Installation
1. Remove the floor console. For additional information, refer to Section 501 - 12 .
2. Remove the bolts, then position the bezel upward.
3. Remove the bulb socket from the bezel.
4. Remove the bulb.
5. To install, reverse the removal procedure.
SECTION 307-
05: Automatic Transaxle/Transmission External Controls 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Knob
Removal
1. Remove the shifter top control panel.
2. Disconnect the electrical connectors.
3. Remove the shifter bezel. 4. Remove the bulb from the bezel. SECTION 307-
05: Automatic Transaxle/Transmission External Controls 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

The clutch control system engages and disengages the clutch. The clutch control system disengages
the clutch when the clutch pedal is depressed and engages the clutch when the clutch pedal is
released. Clutch pedal motion is transmitted by the clutch release lever cable to the clutch release
lever. The clutch release hub and bearing engages the clutch pressure plate diaphragm spring,
releasing the pressure on the clutch disc which in turn disengages the transmission from the engine.
The clutch adjusts automatically to compensate for clutch disc wear. The clutch linkage is self-
adjusting.
The clutch pedal position (CPP) switch prevents the starter motor from engaging unless the clutch
pedal is depressed all the way to the floor. The switch plunger is contacted by the clutch pedal and
extends as the clutch pedal is pressed. The clutch pedal position switch is electrically connected in line
with the ignition switch and the starter motor relay coil. The CPP also turns off the speed control when
the clutch pedal is depressed. 4 7L583 Clutch pedal quadrant and pawl assembly Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

z
Is the resistance between 612 and 748 ohms? REFER to
Switch —
Speed Control
Actuator . TEST the
system for normal
operation. A13 CHECK THE BPP SWITCH CIRCUITRY
z
Measure the resistance between speed control servo C122 Pin
4, Circuit 511 (LG), harness side, and speed control servo C122
Pin 10, Circuit 1205 (BK), harness side.
z Is the resistance less than 20 ohms? Yes
GO to
A16 .
No
If automatic
transmission, REPAIR
Circuit 511 (LG) and
Circuit 810 (LG/RD) as
necessary. TEST the
system for normal
operation.
If manual transmission,
GO to A14 .
A14 CHECK CIRCUIT 511 (LG) AND CIRCUIT 810 (RD/LG) FOR
AN OPEN z
Disconnect: CPP Switch C2072.
z Measure the resistance between CPP Switch C2072 Pin 1,
Circuit 511 (LG), harness side and ground.
z Is the resistance less than 20 ohms? Yes
GO to
A15 .
No
REPAIR Circuit 511
(LG) and Circuit 810
(LG/RD) as necessary.
TEST the system for
normal operation. A15 CHECK CIRCUIT 511 (LG) FOR AN OPEN
z
Measure the resistance between speed control servo C122 Pin
4, Circuit 511 (LG), harness side and CPP switch C2072 Pin 2,
Circuit 511 (LG), harness side. Yes
INSTALL a new CPP
switch. TEST the
system for normal
operation.
No
REPAIR the circuit.
TEST the system for
normal operation. Klj . 8 ba
132003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...