AC system FORD MUSTANG 2003 User Guide

z
Change engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
184,000 Km (115,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
192,000 Km (120,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect exhaust system and heat shields.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z Install a new engine air filter.
z Install a new fuel filter. (See ADDITIONAL INFORMATION below.)
z If equipped, install a new cabin air filter.
z Install new accessory drive belt(s) (Escort).
z Install a new PCV valve on all cars and light trucks over 6,000 Gross Vehicle Weight.
z Change automatic transmission/transaxle fluid on all vehicles equipped with AX4S, 4F50N,
4R100, 4F27E. Inspect automatic transmission fluid level using dipstick on all other vehicles, if
equipped.
z Install a new camshaft belt on all 2.0L, 4- cylinder engines (Escort, Focus, ZX2 and Escape).
z If equipped, install new climate controlled seat filters (Navigator, Lincoln LS and Aviator).
ADDITIONAL INFORMATION: Additional services for natural gas and propane vehicles include
inspecting fuel tanks, as well as draining coalescent fuel filter bowl and installing a new filter.
200,000 Km (125,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
z Drain coalescent fuel filter and replace filter (NGV).
208,000 Km (130,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
216,000 Km (135,000 Miles)
zChange engine oil and install a new oil filter. Klj . 8 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
If equipped, inspect automatic transmission fluid level with dipstick.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z Install a new cabin air filter.
z If filled with green engine coolant, change coolant.
224,000 Km (140,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
232,000 Km (145,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
240,000 Km (150,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect exhaust system and heat shields.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z Install a new engine air filter.
z Install a new fuel filter. (See ADDITIONAL INFORMATION below.)
z If equipped, install a new cabin air filter.
z If filled with yellow engine coolant, change coolant or at 8 years, whichever comes first.
z Change automatic transmission/transaxle fluid and filter.
z Change rear axle lubricant on all rear wheel (RWD) vehicles.
z Install a new accessory drive belt(s) (if a new belt has not been installed within the last 100,000
miles).
z If equipped, install new climate controlled seat filters (Navigator, Lincoln LS and Aviator).
ADDITIONAL INFORMATION: If vehicle is registered in California, the California Air Resources Board
(CARB) has determined that failure to install a new fuel filter at this interval will not nullify the emission
warranty or limit recall liability prior to completion of the vehicle's useful life. It is, however
recommended that maintenance checks be carried out and recorded at the indicated intervals.
Additional checks for natural gas and propane vehicles include inspecting fuel tanks, as well as
draining and installing a new filter. Klj . 9 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Noise, Vibration and Harshness (NVH)
Noise is any undesirable sound, usually unpleasant in nature. Vibration is any motion, shaking or
trembling, that can be felt or seen when an object moves back and forth or up and down. Harshness is
a ride quality issue where the vehicle's response to the road transmits sharply to the customer.
Harshness normally describes a firmer than usual response from the suspension system. Noise,
vibration and harshness (NVH) is a term used to describe these conditions, which result in varying
degrees of dissatisfaction. Although, a certain level of NVH caused by road and environmental
conditions is normal. This section is designed to aid in the diagnosis, testing and repair of NVH
concerns.
Acceptable Noise, Vibration and Harshness
All internal combustion engines and drivelines produce some noise and vibration; operating in a real
world environment adds noise that is not subject to control. Vibration isolators, mufflers and dampers
reduce these to acceptable levels. A driver who is unfamiliar with a vehicle can think that some sounds
are abnormal when actually the sounds are normal for the vehicle type. For example, Traction-
Lok®
differentials produce a slight noise on slow turns after extended highway driving. This is acceptable
and has no detrimental effect on the locking axle function. As a technician, it is very important to be
familiar with vehicle features and know how they relate to NVH concerns and their diagnosis. For
example, if the vehicle has automatic overdrive, it is important to test drive the vehicle both in and out
of overdrive mode.
Diagnostic Theory
The shortest route to an accurate diagnosis results from:
zsystem knowledge, including comparison with a known good system.
z system history, including repair history and usage patterns.
z condition history, especially any relationship to repairs or sudden change.
z knowledge of possible sources.
z using a systematic diagnostic method that divides the system into related areas.
The diagnosis and correction of noise, vibration and harshness concerns requires:
za road or system test to determine the exact nature of the concern.
z an analysis of the possible causes.
z testing to verify the cause.
z repairing any concerns found.
z a road test or system test to make sure the concern has been corrected or brought back to
within an acceptable range.
Glossary of Terms SECTION 100-
04: Noise, Vibration and Harshness 2003 Mustang Workshop Manual Klj . 1 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Clonk
A hydraulic knocking sound. Sound occurs with air pockets in a hydraulic system. Also described as
hammering.
Clunk/Driveline Clunk
A heavy or dull, short-
duration, low-frequency sound. Occurs mostly on a vehicle that is accelerating or
decelerating abruptly. Also described as a thunk.
Coast/Deceleration
Releasing the accelerator pedal at cruise, allowing the engine to reduce vehicle speed without
applying the brakes.
Coast/Neutral Coast
Placing the transmission range selector in NEUTRAL (N) or depressing the clutch pedal while at
cruise.
Constant Velocity (CV) Joint
A joint used to absorb vibrations caused by driving power being transmitted at an angle.
Controlled Rear Suspension Height
The height at which a designated vehicle element must be when driveline angle measurements are
made.
Coupling Shaft
The shaft between the transfer case and the front drive axle or, in a two- piece rear driveshaft, the front
section.
CPS
Cycles per second. Same as hertz (Hz).
Cracks
A mid- frequency sound, related to squeak. Sound varies with temperature conditions.
Creak
A metallic squeak.
Cruise
Constant speed on level ground; neither accelerating nor decelerating.
Cycle
The process of a vibrating component going through a complete range of motion and returning to the Klj . 4 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

WOT
The acronym for wide open throttle is WOT.
Tools and Techniques
Electronic Vibration Analyzer (EVA)
The EVA is a hand-
held electronic diagnostic tool which will assist in locating the source of
unacceptable vibrations. The vibration sensor can be remotely mounted anywhere in the vehicle for
testing purposes. The unit displays the three most common vibration frequencies and their
corresponding amplitudes simultaneously. A bar graph provides a visual reference of the relative
signal strength (amplitude) of each vibration being displayed and its relative G force. The keypad is
arranged to make the EVA simple to program and use. Some of the functions include the ability to
average readings as well as record, play back and freeze readings. The EVA has a strobe balancing
function that can be used to detect imbalance on rotating components such as a driveshaft or engine
accessories.
The EVA allows for a systematic collection of information that is necessary to accurately diagnose and
repair NVH problems. For the best results, carry out the test as follows:
a. Test drive the vehicle with the vibration sensor inside the vehicle.
b. Place the sensor in the vehicle according to feel. „If the condition is felt through the steering wheel, the source is most likely in the front of
the vehicle.
„ A vibration that is felt in the seat or floor only will most likely be found in the driveline,
drive axle or rear wheels and tires.
c. Record the readings. Also note when the condition begins, when it reaches maximum intensity, and if it tends to diminish above/below a certain speed.
„Frequencies should be read in the "average" mode. Item Description
1 EVA screen
2 Frequency mode displayed in rpm or Hz
3 Active sensor input (A or B)
4 Current active mode
5 G force indicators or the strongest frequencies in descending strength of each vibration
6 Strength of each vibration
7 Frequency in rpm/Hz of each vibration Klj . 11 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Did any abnormal occurrence coincide with or proceed its appearance?
Use the information gained from the customer to accurately begin the diagnostic process.
Pre- Drive Check
It is important to do a pre- drive check before road testing the vehicle. A pre- drive check verifies that
the vehicle is relatively safe to drive and eliminates any obvious faults on the vehicle.
The pre- drive check consists of a brief visual inspection. During this brief inspection, take note of
anything that will compromise safety during the road test and make those repairs/adjustments before
taking the vehicle on the road.
Preparing for the Road Test
Observe the following when preparing for the road test:
zReview the information recorded on the NVH Diagnostic Guide. It is important to know the
specific concern the customer has with the vehicle.
z Do not be misled by the reported location of the noise/vibration. The cause can actually be
some distance away.
z Remember that the vibrating source component (originator) may only generate a small
vibration. This small vibration can in turn cause a larger vibration/noise to emanate from another
receiving component (reactor), due to contact with other components (transfer path).
z Conduct the road test on a quiet street where it is safe to duplicate the vibration/noise. The ideal
testing route is an open, low- traffic area where it is possible to operate the vehicle at the speed
in which the condition occurs.
z If possible, lower the radio antenna in order to minimize turbulence. Identify anything that could
potentially make noise or be a source of wind noise. Inspect the vehicle for add- on items that
create vibration/noise. Turn off the radio and the heating and cooling system blower.
z The engine speed is an important factor in arriving at a final conclusion. Therefore, connect an
accurate tachometer to the engine, even if the vehicle has a tachometer. Use a tachometer that
has clearly defined increments of less than 50 rpm. This ensures an exact engine speed
reading.
Verify the Customer Concern
Verify the customer concern by carrying out a road test, an engine run- up test, or both.
The decision to carry out a road test, an engine run- up test, or both depends on the type of NVH
concern. A road test may be necessary if the symptom relates to the suspension system or is sensitive
to torque. A drive engine run- up (DERU) or a neutral engine run- up (NERU) test identifies noises and
vibrations relating to engine and drivetrain rpm. Remember, a condition will not always be identifiable
by carrying out these tests, however, they will eliminate many possibilities if carried out correctly.
Road Test Klj . 5 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

NOTE:
A serpentine drive belt decreases the usefulness of this test. In these cases, use a
vibration analyzer, such as the VA, to pinpoint accessory vibrations. An electronic listening
device, such as an EngineEAR, will also help to identify noises from specific accessories.
Remove the accessory drive belts.
z Increase the engine rpm to where the concern occurs.
z If the vibration/noise is duplicated when carrying out this test, the belts and accessories are not
sources.
z If the vibration/noise was not duplicated when carrying out this test, install each accessory belt,
one at a time, to locate the source.
Vehicle Cold Soak Procedure
To carry out this procedure, proceed as follows:
zTest preparations include matching customer conditions (if known). If not known, document the
test conditions: gear selection and engine rpm. Monitor the vibration/noise duration with a watch
for up to three minutes.
z Park the vehicle where testing will occur. The vehicle must remain at or below the concern
temperature (if known) for 6- 8 hours.
z Before starting the engine, conduct a visual inspection under the hood.
z Turn the key on, but do not start the engine. Listen for the fuel pump, anti- lock brake system
(ABS) and air suspension system noises.
z Start the engine.
z CAUTION: Never probe moving parts.
Isolate the vibration/noise by carefully listening. Move around the vehicle while listening to find
the general location of the vibration/noise. Then, search for a more precise location by using a
stethoscope or EngineEAR.
z GO to Symptom Chart — Idle Noise/Vibration to assist with the diagnosis.
6: Check OASIS/TSBs/Repair History
After verifying the customer concern, check for OASIS reports, TSBs and the vehicle repair history for
related concerns. If information relating to a diagnosis/repair is found, carry out the procedure(s)
specified in that information.
If no information is available from these sources, carry out the vehicle preliminary inspection to
eliminate any obvious faults.
7: Diagnostic Procedure
Qualifying the concern by the particular sensation present can help narrow down the concern. Always
use the "symptom" to "system" to "component" to "cause" diagnosis technique. This diagnostic method
divides the problem into related areas to correct the customer concern.
zVerify the "symptom".
z Determine which "system(s)" can cause the "symptom".
„If a vibration concern is vehicle speed related, the tire and wheel rpm/frequency or
driveshaft frequency should be calculated.
„ If a vibration concern is engine speed related, the engine, engine accessory or engine
firing frequencies should be calculated. Klj . 9 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
After determining the "system", use the diagnostic tools to identify the worn or damaged
"components".
z After identifying the "components", try to find the "cause" of the failure.
Once the concern is narrowed down to a symptom/condition, proceed to NVH Condition and Symptom
Categories.
NVH Condition and Symptom Categories
A good diagnostic process is a logical sequence of steps that lead to the identification of a causal
system. Use the condition and symptom categories as follows:
zIdentify the operating condition that the vehicle is exhibiting.
z Match the operating condition to the symptom.
z Verify the symptom.
z Identify which category or system could cause the symptom.
z Refer to the diagnostic symptom chart that is referred to.
Operating Condition— Vehicle is Not Moving
1. Static operation zNoise occurs during component/system functioning. GO to Symptom Chart — Squeak
and Rattle .
2. While cranking 1. Grinding or whine, differential ring gear or starter motor pinion noise. GO to Symptom Chart — Engine Noise/Vibration .
2. Rattle. Exhaust hanger, exhaust heat shield or A/C line noise. GO to Symptom Chart —
Squeak and Rattle .
3. Vibration. Acceptable condition.
3. At idle zIdle noise. GO to Symptom Chart — Idle Noise/Vibration .
z Idle vibration or shake. GO to Symptom Chart — Idle Noise/Vibration .
4. During Gear Selection 1. Vehicle parked on a steep incline. Acceptable noise.
2. Vehicle parked on a flat surface. GO to Symptom Chart — Driveline Noise/Vibration .
3. Vehicle with a manual transmission. GO to Symptom Chart — Transmission (Manual)
and Transfer Case Noise/Vibration .
Operating Condition— Vehicle is Moving
1. Depends more on how the vehicle is operated 1. Speed related
„Related to vehicle speed
„Pitch increases with vehicle speed. GO to Symptom Chart — Tire
Noise/Vibration .
„ Noise occurs at specific vehicle speed. A high- pitched noise (whine). GO to
Symptom Chart — Driveline Noise/Vibration . Klj . 10 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

„
Loudness proportional to vehicle speed. Low- frequency noise at high
speeds, noise and loudness increase with speed. GO to Symptom Chart —
Driveline Noise/Vibration .
„ A low- pitched noise (drumming). GO to Symptom Chart — Engine
Noise/Vibration .
„ Vibration occurs at a particular speed (mph) regardless of acceleration or
deceleration. GO to Symptom Chart — Tire Noise/Vibration .
„ Noise varies with wind/vehicle speed and direction. GO to Symptom Chart — Air Leak and Wind Noise .
„ Related to engine speed.
„Noise varies with engine rpm. GO to Symptom Chart — Engine
Noise/Vibration .
„ Vibration occurs at a particular speed (mph) regardless of engine speed
(rpm).
2. Acceleration
„Wide open throttle (WOT)
„Engine induced contact between components. Inspect and repair as
necessary.
„ Noise is continuous throughout WOT. Exhaust system or engine ground
out. GO to Symptom Chart — Engine Noise/Vibration .
„ Light/moderate acceleration
„Tip- in moan. Engine/exhaust noise. GO to Symptom Chart — Engine
Noise/Vibration .
„ Knock-type noise. GO to Symptom Chart — Engine Noise/Vibration .
„ Driveline shudder. GO to Symptom Chart — Driveline Noise/Vibration .
„ Engine vibration. GO to Symptom Chart — Engine Noise/Vibration .
3. Turning noise. GO to Symptom Chart — Steering Noise/Vibration .
4. Braking
„Clicking sound is signaling ABS is active. Acceptable ABS sound.
„ A continuous grinding/squeal. GO to Symptom Chart — Brake Noise/Vibration .
„ Brake vibration/shudder. GO to Symptom Chart — Brake Noise/Vibration .
5. Clutching
„A noise occurring during clutch operation. GO to Symptom Chart — Transmission
(Manual) and Transfer Case Noise/Vibration .
„ Vibration. GO to Symptom Chart — Transmission (Manual) and Transfer Case
Noise/Vibration .
6. Shifting
„Noise or vibration condition related to the transmission (automatic). GO to
Symptom Chart — Transmission (Automatic) Noise/Vibration .
„ Noise or vibration related to the transmission (manual). GO to Symptom Chart —
Transmission (Manual) and Transfer Case Noise/Vibration .
7. Engaged in four- wheel drive. GO to Symptom Chart — Transmission (Manual) and
Transfer Case Noise/Vibration .
8. Cruising speeds
„Accelerator pedal vibration. GO to Symptom Chart — Engine Noise/Vibration .
„ Driveline vibration. GO to Symptom Chart — Driveline Noise/Vibration .
„ A shimmy or shake. GO to Symptom Chart — Tire Noise/Vibration .
9. Driving at low/medium speeds Klj . 11 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

components as necessary.
z Broken
powertrain
mounts. z
INSPECT the powertrain
mounts. INSTALL new
mounts as necessary.
REFER to Section 303 - 01A
for 3.8L engines or
Section 303 - 01B for 4.6L (2V)
engines.
z Idle speed too
high. z
CHECK for the correct idle
speed.
z Driveline clunk—
occurs as the vehicle
starts to move
forward following a
stop z
Worn or galled
driveshaft slip-
yoke splines. z
CLEAN and INSPECT the
splines of the yoke for a
worn or galled condition.
INSTALL a new yoke as
necessary. REFER to
Section 205 - 01 .
z Worn or galled
driveshaft and
coupling shaft
splines. z
CLEAN and INSPECT the
splines of the driveshaft and
coupling shaft for a worn or
galled condition. INSTALL a
new driveshaft assembly as
necessary. REFER to
Section 205 - 01 .
z Loose rear leaf
spring U- bolts. z
CHECK the U- bolts for
loose nuts. TIGHTEN to
specification. REFER to
Section 204 - 02 .
z Driveline clunk (FWD
vehicles)—occurs
during acceleration or
from cruise to
coast/deceleration z
Damaged or
worn inboard
constant velocity
(CV) joint. z
INSPECT the inboard CV
joint and boot. REPAIR or
INSTALL a new CV joint as
necessary.
z Driveline clunk (4WD
vehicles)—occurs
during shift- on-the- fly
engagement z
Clutch relay.
z Shift motor.
z Transfer case.
z GEM. z
CHECK the 4WD
engagement system.
REPAIR or INSTALL new
components as necessary.
z Clicking, popping or
grinding— occurs
while vehicle is
turning z
Inadequate or
contaminated
lubrication in the
(CV) joints. z
CHECK the CV boots and
joints for wear or damage.
REPAIR or INSTALL new
components as necessary.
z Another
component
contacting the
halfshaft. z
CHECK the halfshafts and
the area around the
halfshafts. REPAIR as
necessary.
z Brake
components. z
INSPECT the front brakes
for wear or damage.
REPAIR as necessary.
REFER to Section 206 - 03 .
z Steering
components. z
INSPECT the drag link,
inner and outer tie- rods or
idler arm for wear or
damage. REPAIR as
necessary. REFER to
Section 211 - 02 .
z Suspension
components. z
INSPECT the upper and
lower ball joints for wear or
damage. REPAIR as
necessary. REFER to Klj . 19 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...