rele FORD MUSTANG 2003 Workshop Manual

5.
CAUTION: Folding the headliner will result in damage to the headliner.
Remove the headliner. 1. Disconnect the electrical connector.
2. Release the wiring harness locators.
3. Remove the headliner.
Installation 1. CAUTION: Folding the headliner will result in damage to the headliner.
Install the headliner. 1. Position the headliner.
„Apply Headliner Adhesive F1VY-19562-A meeting Ford specification WSS-
M2G355- B, to the headliner using the existing pattern.
2. Connect the electrical connector.
3. Engage the wiring harness locators.
2. Install the two pin- type retainers. 3. Install the two sun visors. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

5. Release the clips.
1. Lift up to release the two clips.
2.NOTE: Grasp the roof side moulding and lift up to release the money clip.
Remove the money clip.
6. Remove the upper quarter trim panel. For additional information, refer to Section 501 - 05 .
7. Remove the nuts and the roof side moulding. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Rear Spoiler
Removal and Installation
1. Open the luggage compartment lid.
2. Disconnect the high mounted stoplamp electrical connector.
3. Remove the screws and the nuts.
4. CAUTION: Use care not damge the pin- type retainers and pin-type retainer seals
during removal.
Release the spoiler from the two pin- type retainers in an upward motion.
SECTION 501-
08: Exterior Trim and Ornamentation 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Switch —
Exterior Rear View Mirror Control
Removal
1. CAUTION: Use a shop towel or similar material between the tool and the front door
trim panel or damage to the front door trim panel may occur.
Position the window regulator switch plate aside. 1. Pull at service notch.
2. Lift to release the clip at the rear edge.
2. Remove the power exterior rear view mirror control switch. zDisconnect the electrical connector.
Installation 1. To install, reverse the removal procedure.
SECTION 501-
09: Rear View Mirrors 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Seats
Seats —
Front Power
The front power seat features:
za six- way seat regulator control switch (14A701) located on the front of the seat.
z a seat track (61705) mounted under the seat.
z a seat regulator motor (14547) and gear housing mounted on the seat track (61705).
z an optional power lumbar switch located on the outboard side of the seat (14C715).
z a manual seat backrest release handle on the outboard rear corner of the seat.
z an optional power bolster and lumbar switches located on the inboard side of the seat (Cobra
only)
Seats — Power Lumbar Support
NOTE: The pump and solenoid module are serviced as an assembly with the front seat cushion frame
(Cobra only). The backrest bolster/lumbar adjusting pads are serviced together and the cushion
bolsters are serviced separately.
The power lumbar support system consists of: SECTION 501-
10: Seating 2003 Mustang Workshop Manual Item Part Number Description
1 611A08 Front seat backrest head restraint
2 65500 Front seat backrest pad adjuster
3 14C715 Seat control switch
4 14A701 Lumbar control switch
5 — Bolster and lumbar control switches (Cobra only) Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
seat control switch (14C715)
z front seat backrest pad adjusting pump (65530)
z front seat adjusting motor drive tube (618B62)
z system wiring and circuit protection
z front seat backrest adjusting hose (65528)
z driver backrest and cushion bolster (Cobra)
z driver bolster and lumbar adjusting pad pump motor and solenoid module (Cobra)
z driver bolster and lumbar control switch (Cobra)
z driver seat cushion adjusting hose (Cobra)
Seats — Front Seat Backrest Latch
NOTE: Under no circumstances are the front seat backrest latch components to be repaired as
individual components. If a front seat backrest latch (62648) or component is non- functional or
damaged, a new front seat backrest latch must be installed.
A release handle on the outboard rear corner of the seat backrest is manually operated to unlock the
front seat backrest latch.
Rear Seat
The rear seat cushion pad and frame (600A88) is retained in the following manner:
zPins are located on the bottom front of the rear seat cushion pad and frame which secure the
rear seat cushion pad and frame to the front floor pan (11135).
z The pins are inserted into locking plates on the floor crossmember with a push button release.
z The bottom of the rear seatback frame is retained with screws to the front floor pan. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Vehicles with power bolster and lumbar
6. Remove the two screws for the power bolster and lumbar switch bezel.
7. Disconnect the power lumbar switch and the bolster switches.
8. Pinch the release tabs on the affected switch and push the switch through the bezel.
All vehicles 9. To install, reverse the removal procedure. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Lumbar Assembly
Removal and Installation
All vehicles
1. Remove the front seat. For additional information, refer to Seat — Front Power in this section.
2. Release the J- clip.
3. Remove the seat backrest latch handle knob (62762).
4. Pull the seat backrest trim cover up to the top of the seat.
5. Remove the seat backrest foam pad from the seat backrest frame.
Vehicles with standard power lumbar SECTION 501-
10: Seating 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Lumbar Motor
Removal and Installation
All vehicles
1. Remove the front seat. For additional information, refer to Seat — Front Power in this section.
2. Disconnect the power seat track electrical connector.
3. Remove the four seat track bolts.
Vehicles with standard power lumbar 4. Release the J- clip.
5. Remove the front seat backrest pad adjusting pump screws.
SECTION 501-
10: Seating 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

6. Remove the front seat backrest pad adjusting pump (65530).
1. Disconnect the electrical connector.
2. Disconnect the power lumbar support air hose.
Vehicles with power bolster and lumbar 7. Remove the driver seat backrest latch. For additional information, refer to Latch — Front Seat
Backrest in this section.
8. Remove the pivot bolt and seat backrest. zDisconnect the power lumbar support air hoses.
9. Release the J- clips. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...