rele FORD MUSTANG 2003 Workshop Manual

REMOVAL AND INSTALLATION
Latch —
Front Seat Backrest
Removal
NOTE: The power seat backrest adjuster assembly must be installed as a new unit. Repair of the
power seat backrest adjuster assembly components is not acceptable and should not be attempted.
1. Remove the two screws and the seat backrest latch cover.
2. Remove the seat backrest latch handle knob (62762).
3. Release the J- retainer.
4. Remove the screw.
SECTION 501-
10: Seating 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DISASSEMBLY AND ASSEMBLY
Front Seat Backrest
Disassembly and Assembly
All vehicles
1. Remove the front seat backrest. For additional information, refer to Front Seat Backrest in this
section.
2. Remove the front seat backrest head restraint (611A08).
3. Remove the screws and the safety belt guide.
4. Remove the front seat headrest guide rod sleeve (610A16). 5. Release the J - clip. SECTION 501-
10: Seating 2003 Mustang Workshop Manual Klj . 1 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

10. Release the front seat backrest frame (61018) from the front seat backrest foam pad.
Vehicles with standard power lumbar 11. Remove the seat backrest lumbar adjuster pad.
Vehicles with power bolster and lumbar 12. Remove the two screws and the seat backrest lumbar and bolster adjuster pad. Klj . 3 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

B1450 Wiper Wash/delay Switch
Circuit Failure GEM GO to
Section 501 - 16 .
B1453 Wiper Wash/delay Switch
Circuit Short to Ground GEM GO to
Section 501 - 16 .
B1458 Wiper Washer Pump Motor
Relay Circuit Failure GEM GO to
Section 501 - 16 .
B1460 Wiper Washer Pump Motor
Relay Circuit Short to Battery GEM GO to
Section 501 - 16 .
B1462 Safety Belt Switch Circuit
Failure GEM GO to
Section 413 - 09 .
B1466 Wiper High/low Speed Not
Switching GEM GO to
Section 501 - 16 .
B1473 Wiper Low Speed Circuit
Motor Failure GEM GO to
Section 501 - 16 .
B1476 Wiper High Speed Circuit
Motor Failure GEM GO to
Section 501 - 16 .
B1498 Decklid Punch-
out Sensor
Ground Short GEM GO to
Section 419 - 01 .
B1551 Decklid Release Circuit
Failure GEM GO to
Section 501 - 14B .
B1553 Decklid Release Circuit Short
to Battery GEM GO to
Section 501 - 14B .
B1555 Ignition RUN/START Circuit
Failure GEM GO to
Section 211 - 05 .
B1603 Lamp Anti-
Theft Indicator
Circuit Failure GEM GO to
Section 419 - 01 .
B1605 Lamp Anti-
Theft Indicator
Circuit Short to Battery GEM GO to
Section 419 - 01 .
B1687 Lamp Dome Input Circuit
Short to Battery GEM GO to
Section 417 - 02 .
B1833 Door Unlock Disarm Switch
Circuit Short to Ground GEM GO to
Section 419 - 01 .
B2486 Parklamp Output Relay Driver
Circuit Failure GEM GO to
Section 419 - 01 .
B2488 Parklamp Output Relay Driver
Circuit Short to Battery GEM GO to
Section 419 - 01 .
C1189 Brake Fluid Level Sensor
Input Circuit Short to Ground GEM REFER to
Section 413 - 01 .
C1223 Lamp Brake Warning Output
Circuit Failure GEM REFER to
Section 413 - 01 .
C1225 Lamp Brake Warning Output
Circuit Short to Battery GEM REFER to
Section 413 - 01 .
ICM DIAGNOSTIC TROUBLE CODE (DTC) INDEX DTC Description Source Action
B1343 Heated Backlight Input Circuit Failure ICM GO to
Pinpoint Test H . Klj . 4 ba
322003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Switch —
Window Regulator Control
Removal
1. CAUTION: Use a shop towel or similar material between the tool and the door trim
panel or damage to the door trim panel may occur.
Position the window regulator switch plate aside. 1. Pull at the service notch.
2. Lift to release the clip at the rear edge.
2. Remove the window regulator control switch. 1. Remove the screws.
2. Disconnect the connectors.
Installation 1. To install, reverse the removal procedure.
SECTION 501-
11: Glass, Frames and Mechanisms 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Rear Window Defrost Switch
Removal and Installation
1. Remove the instrument panel center finish panel. For additional information, refer to Section 501 - 12 .
2. Release the clips and remove the rear window defrost switch.
3. To install, reverse the removal procedure.
SECTION 501-
11: Glass, Frames and Mechanisms 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Coupe
8. Remove the sun visors and clips zRemove the screws.
z Remove the clips.
9. Remove the roof side trim moulding. For additional information, refer to Section 501 - 08 .
10. Lower the front portion of the headliner.
All vehicles 11. Remove the two windshield wiper pivot arms. 1. Raise up on the pivot arms.
2. Release the retainer tabs, and release the windshield wiper pivot arms.
12. Remove the cowl grille weatherstrip. Klj . 3 ba
102003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Instrument Panel
Removal
CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to
these charges, damage may result.
1. Remove the driver air bag module. For additional information, refer to Section 501 - 20B .
2. Remove the passenger air bag module. For additional information, refer to Section 501 - 20B .
3. Remove the LH front wheel and tire assembly. For additional information, refer to Section 204 -
04 .
4. Position the LH fender splash shield away from the dash panel. 1. Remove the pin- type retainers.
2. Remove the screws.
3. Position the LH fender splash shield away from the dash panel.
5. Disconnect the bulkhead electrical connector from inside the fender opening. 1. Loosen the bolt.
2. Disconnect the bulkhead electrical connector.
6. Release the bulkhead electrical connector from the dash panel.
SECTION 501-
12: Instrument Panel and Console 2003 Mustang Workshop Manual Klj . 1 ba
152003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

2. Separate the intermediate shaft from the steering column shaft.
22. NOTE: The corner of the carpet may have to be pulled back slightly to carry out this step.
Disconnect the LH main wiring harness electrical connectors.
23. Disconnect the generic electronic module (GEM) electrical connectors.
24. Disconnect the electronic crash sensor (ECS) module electrical connector. 1. Release the locking tab.
2. Disconnect the ECS module electrical connector. Klj . 5 ba
152003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

25. If equipped, disconnect the shift interlock assembly from the selector lever.
1. Remove the screw.
2. Remove the R- clip.
3. Disconnect the shift interlock cable.
4. Disconnect the shift interlock assembly from the selector lever.
26. Remove the audio unit. For additional information, refer to Section 415 - 01 .
27. If equipped, disconnect the shifter assembly electrical connector.
28. NOTE: This step is being carried out through the audio unit opening.
NOTE: Rotate the temperature control switch to the cool position.
Release the temperature control cable from the blend door.
29. Remove the four center instrument panel support bolts. Klj . 6 ba
152003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...