clutch FORD MUSTANG 2003 Repair Manual

11 N620482 Dowel
12 87836 Plug
Item Part Number Description
1 N807198 Dowel pin (2 req'd)
2 N807309 Bolt
3 N807959 Bolt
4 18663 Heater water hose
5 W500110 Bolt (2 req'd)
6 12A699 Knock sensor (2 req'd)
7 N807309 Bolt (2 req'd)
8 18696 Heater water hose
9 7120 Pilot bearing
10 6K318 Crankshaft rear retainer
11 N806155 Bolt (6 req'd)
12 6310 Crankshaft oil slinger
13 6375 Flexplate
14 N806168 Bolt (6 req'd)
15 — Flywheel
16 N808139 Bolt (8 req'd)
17 7550 Clutch disc
18 7563 Clutch pressure plate
19 N808969 Bolt (6 req'd)
20 6701 Crankshaft rear oil seal
21 N806007 Dowel pin (2 req'd) Klj . 13 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Valve Cover LH
Removal
All vehicles 1. Remove the air intake scoop. For additional information, refer to Section 303 - 12 .
2. Remove the Hydro- Boost brake booster. For additional information, refer to Section 206 - 07 .
3. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
Manual transmission vehicles
4. Remove the screw and the dust shield.
5. Disengage the clutch release cable from the clutch release fork.
SECTION 303-
01D: Engine — Mach I 4.6L (4V) 2003 Mustang Workshop Manual Material
Item Specification
Metal Surface Cleaner
F4AZ-
19A536- RA or
equivalent WSE-
M5B392- A Silicone Gasket and Sealant
F7AZ-
19554- EA or equivalent WSE-
M4G323-
A4 Klj . 1 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. Lower the vehicle.
7. Remove the two screws and position the clutch release cable aside.
All vehicles 8. Remove the LH ignition coil cover bolts and the cover.
9. Disconnect the ignition coil electrical connectors.
10. Remove the ignition coils. Klj . 2 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Manual transmission vehicles
10. Install the clutch release cable and install the two screws.
11. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
12. Connect the clutch release cable to the clutch release fork.
13. Install the dust shield and the screw. Klj . 7 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Engine Front Cover
Removal
All vehicles 1. Remove the air intake scoop bracket. For additional information, refer to Section 303 - 12 .
2. Remove the RH valve cover. For additional information, refer to Valve Cover RH in this section.
3. Remove the Hydro- Boost brake booster. For additional information, refer to Section 206 - 07 .
Manual transmission vehicles
4. Remove the two clutch release cable retaining screws.
All vehicles 5. Remove the LH ignition coil cover bolts and the cover.
SECTION 303-
01D: Engine — Mach I 4.6L (4V) 2003 Mustang Workshop Manual Material
Item Specification
Metal Surface Cleaner
F4AZ-
19A536- RA or equivalent WSE-
M5B392-
A Silicone Gasket and Sealant
F7AZ-
19554- EA or equivalent WSE-
M4G323-
A4 SAE 5W-
30 Premium Synthetic
Blend Motor Oil
XO- 5W30-QSP or equivalent WSS-
M2C153-
G Klj . 1 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

27. Remove the drain plug and drain the oil.
zInstall the drain plug when finished.
28. Remove the front four oil pan bolts.
Manual transmission vehicles 29. Remove the bolt and the clutch release cable shield.
30. Disengage the clutch release cable from the clutch release fork. Klj . 7 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

8. Install the LH valve cover and loosely install the bolts.
9. Tighten the LH valve cover bolts in the sequence shown.
10. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
Manual transmission vehicles 11. Connect the clutch release cable to the clutch release fork. Klj . 13 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

12. Install the clutch release cable shield and the bolt.
All vehicles 13. Loosely install the four oil pan bolts. Tighten the bolts in three stages, and in the sequence shown. 1. Stage 1: Tighten the bolts to 2 Nm (18 lb- in).
2. Stage 2: Tighten the bolts to 20 Nm (15 lb- ft).
3. Stage 3: Tighten the bolts an additional 90 degrees (1/4 turn). 14. Position the wiring harness and install the nuts. Klj . 14 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Manual transmission vehicles
36. Install the clutch release cable screws.
All vehicles 37. Install the RH valve cover. For additional information, refer to Valve Cover RH in this section.
38. Install the Hydro- Boost brake booster. For additional information, refer to Section 206 - 07 .
39. Install the air intake scoop bracket. For additional information, refer to Section 303 - 12 .
40. Fill the crankcase with clean engine oil. Klj . 20 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Flywheel
Removal 1. Remove the clutch components. For additional information, refer to Section 308 - 01 .
2. Remove the bolts and the flywheel.
Installation 1. To install, reverse the removal procedure.
SECTION 303-
01D: Engine — Mach I 4.6L (4V) 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...