lock GREAT WALL HOVER 2006 Service Repair Manual

Brake-13
Check the component of front brake
1. Measure the thickness of the brake block bush.
standard thickness: 9.0mm
minimum thickness: 2.0mm
It should replace the brake block if less than minimum thickness or
has uneven abrasion.
2. Measure the thickness of the brake disc.
standard thickness: 26.0mm
minimum thickness: 24.0mm
It should repair or replace the brake disc if the brake disc is damaged
or worn or its thickness is
less than minimum thickness.
3. Measure the circular runout of the brake disc.
Remarks: It should ensure that the bearing is adjusted correctly
before the measurement . maximum circular runout : 0.11mm
4. Replace the brake disc if necessary.
a. Remove the tong bracket form the steering knuckle.
b. Remove the hub and brake disc. (Refer to section “Front hub”)
c. Install the new brake disc; tighten the connecting bolt to the
specified torque.
Tightening force: 90
100Nm.
d. Install the hub and brake disassembly. (Refer to section “Front
hub”)
e. Install the tong bracket on the steering knuckle; tighten the
connecting bolt to the specified torque.
Tightening torque 140
10Nm.

Brake-15
Installation of brake caliper
1. Install the brake block
2. Install the brake pump
a. Install the brake pump.
b. Install and tighten the hexagon flange bolt.
Tightening force: 25
35Nm
3. Connect the brake pipeline
Connect the brake oil pipe to the tong body.
Tightening force: 50
5Nm
4. Fill up the brake liquid reservoir with the brake fluid and dis
charge the air in brake system.
5. Check for the leakage of brake fluid.
Caution: Discharge the air after the completion of replacement.

Brake-16
Rear brake (Disk-and-drum type)
tong bracket
pin rubber cover
brake caliper locking bolt 100
silencing plate
combination
outside brake block
inside brake block
brake block wearing
indication plate
cylinder hole
dustproof cover
wire clip
rectangle seal ring
piston
tong body (left)
copper washer
brake oil pipe fastening blot 55
location pin 2530
bleed screw
bleed screw dustproof cover
guide pin 2530
rear brake oil pipeline
N
m: specified torque
peepholesilencing
plate
Replacement of brake block
Remarks: if the rear wheel generates the cheep during the braking,
it should check the abrasion indication plate of brake block. If the
indication plate has the abrasion mark with brake disc, then it
should replace the brake block .
1. Remove the rear wheel
2. Check the thickness of brake block bush.
Measure the thickness of the brake block bush (abrasion material)
from the eyehole of tong. If the thickness is not within the specified
range, then it should replace the brake block.
minimum thickness: 2.0mm.

Brake-17
3. Uplift the brake pump
a. Remove the location pin.
b. Uplift the brake pump and hang it with a rope to protect the brake
oil pipe.
Remarks: do not remove the brake oil pipe.
4. Remove the following components:
a. Two brake blocks
b. Two silencing plates
c. Two silencing plate combinations
d. One brake block bush wearing indication plate
e. Two brake block circlips
5. Measuring the depth of brake discs
(refer to the step 2 of measuring the components of rear brake)
6. Measuring the brake disc circular runout
(Refer to step 3 of measuring the components of rear brake)
7. Install the brake block Circlip

Brake-18
8. Install new brake block
a. Install a brake block bush wearing indication plate on the internal
brake block.
b. Install one silencing plate and one silencing plate combination on
each brake block.
Remarks: Coat the two sides of silencing plate with disc brake
oil (which cannot be replaced with oil of other models).
c. Install two brake blocks, make the wearing indication plate in the
lower position (near the tank cylinder).
Remarks: The working surface of the brake block and brake
disc are not allowed to be contaminated by grease and paint.
9. Install the sub pump
a. Unscrew the release screw, absorb some of the brake fluid.
b. Press the plunger with hammer beam or similar tools, and unscrew
the release screw at the same time.
Tightening force: 8
13Nm
Remarks: Only the brake block of one wheel can be replaced for
once, lest the plunger on the opposite side be bounced.
c. Install and tighten the location pin.
Tightening force: 25
30Nm
10. Install the rear wheel
Tightening force: 120N
m
11. Fill up with the brake fluid and drain the air in the brake
system after the completion of replacement.

Brake-19
Removal of brake pump
1.Remove the brake pipeline
Remove the brake pipeline. Use a container to contain the brake fluid.
2. Remove the pump form the bracket
a. Remove the location pin and guide pin.
b. Remove the tong.
3. Remove the brake block
a. Two pieces of brake block
b. Two pieces of silencing plate
c. Two pieces of silencing plate combination
d. One piece of brake block bush abrasion indicating plate
e. Two brake block circlips
Disassembly of brake pump
1. Remove the piston form the tong
a. Insert the cleaning cloth or other soft cloth into the place between
piston and tong.
b. Use the compressed air to remove the piston and cylinder hole
dustproof cover from the tong.
Warning: it must not place the finger in front of the piston when
use the compressed air.
2. Remove the piston gasket form the tong
Use the screwer to remove the piston gasket.

Brake-20
Check the components of rear brake
1. Measure the thickness of the brake block bush.
Standard thickness: 8.0mm
Minimum thickness: 2.0mm
It should replace the brake block if less than minimum thickness or
has uneven abrasion.
2. Measure the thickness of brake disc.
standard thickness: 18.0mm
minimum thickness: 16.0mm
It should repair or replacement brake disc if it is scratched or worn or
its thickness is less than minimum thickness.
3. Measure the circular runout of brake disc.
Remarks: It should ensure that the rear bearing is adjusted
correctly before the measurement.
Maximum circular runout : 0.11mm
4. Replace the brake disc if necessary.
a. Remove the bracket form the rear axle flange.
b. Remove the rear brake disc and install the new brake disc .
c. Install the bracket and tighten the fastening brake caliper bolt.
Tightening force: 100
5Nm

Brake-21
Assembly of pump
1. During the assembly, coat the guide pin with the proper vacuum
sili con based grease; coat the operating surface of piston and
square gasket with proper rubber lubricant.
2. Install the piston gasket and piston in the tong
3. Install the cylinder hole dustproof cover and wire clip in the
tong.
4. Install the rubber pin cover on the tong bracket.
Installation of brake caliper
1. Install the brake block

Brake-27
6Install the lower tension spring
Install the lower tension spring between the front and rear shoe plate.
7. Install the clearance-adjusting device.
Install the clearance-adjusting device after poke the brake shoe by
screwer.
8. Install two upper release springs
Insert the block into the support pin, then install the upper release
spring on the place between two brake assemblies.
9. Check the operating process of automatic adjusting mechanism.
a. Pull the manual brake pill-wire, then release it. Check the clear-
ance-adjusting gear for rotation. If can not rotate, check the rear
brake and find the problem.
b. Adjust the clearance-adjuster to the length as short as possible.

Brake-28
10. Adjust the clearance between the brake drum and brake shoe.
Poke the adjusting hole plug on the brake drum, insert the screwdriver
into the clearance-adjusting hole; rotate the clearance-adjusting gear
to expand the brake shoe until the brake disc can not be rotated by
hand. Then rotate it for 3-5 teeth in anticlockwise, rotate the brake
disc by hand at the same time, it is proper that it can rotate freely
and without the contact between the abrasion and disc. It is allowable
that the non-running-in brake shoe has the slight abrasion sensing.
When adjust the clearance, the left and right wheel must be adjust at
the same, install the adjusting hole plug after the completion of
adjusting .
11.Rear brake caliper assembly
12.Rear wheel assembly
Tighten torque :120N.m