HONDA CIVIC COUPE 2016 10.G Quick Guide

134 || 135
MAINTENANCE
MAINTENANCE
Recommended Engine Oil
•  Honda Genuine Motor Oil
•  Premium-grade 0W-20 detergent oil with an API Certication Seal on the
container
This seal indicates the oil is energy conserving and
that it meets the American Petroleum Institute’s latest requirements. Use Honda Genuine Motor Oil or another commercial engine oil of suitable viscosity for the ambient temperature as shown.
You may also use synthetic motor oil if it is labeled with the API Certication Seal and is of the specied viscosity grade.
Adding Oil
1. Unscrew and remove the engine oil ll cap.
2. Add oil slowly.
3. Reinstall the engine oil ll cap, and tighten it securely.
4. Wait for three minutes and recheck the engine oil dipstick.
Ambient temperature
Engine oil ll cap
1.5 ℓ engine models
Engine oil ll ca p
2.0 ℓ engine models
Do not ll the engine oil above the upper mark. Overlling the engine oil can result in leaks and engine damage.
NOTICE
Resetting the Engine Oil Life
If you change or replace the vehicle’s engine oil yourself, you must reset the engine oil life.
Models with information display
1. Press the TRIP knob in the instrument panel until
the engine oil life appears in the display.
2. Press and hold the knob for 10 seconds or more, until the display begins to blink.
3. Press and hold the knob for 5 seconds or more. The engine oil life display returns to 100%.
Models with Driver Information Interface
Use the steering wheel buttons to make and enter selections (see page 29).
1. Scroll to the Maintenance Minder screen, and select it.
2. Press and hold the ENTER button for about 10 seconds to enter the reset mode.
3. Scroll to the maintenance item you want to reset (or All Due Items), and select it.
Models with Display Audio
Use the touchscreen to make and enter selections.
1. From the HOME screen, select Settings.
2. Select Vehicle.
3. Select Maintenance Info.
4. Select Select Reset Items.
5. Select an item on the list to reset.
Failure to reset the engine oil life after a maintenance service results in the system showing incorrect maintenance intervals, which can lead to serious mechanical problems.
NOTICE

136 || 137
MAINTENANCE
MAINTENANCE
Engine Coolant
Park the vehicle on level ground. Check the reserve tank and the coolant level in the
radiator. We recommend Honda Long Life Antifreeze/Coolant Type 2.
Checking the Coolant
1. Check the amount of coolant in the reserve tank.
2. If the coolant level is below the MIN mark, add
the specied coolant until it reaches the MAX mark.
3. Inspect the cooling system for leaks.
Adding Coolant
1. Make sure the engine and radiator are cool.
2. Turn the reserve tank cap counterclockwise and relieve any pressure in the coolant system. Do not push the cap down when turning.
3. Push down and turn the reserve tank cap counterclockwise to remove it.
4. Pour coolant into the reserve tank until it reaches the MAX mark.
5. Put the reserve tank cap back on, and tighten it fully.
If temperatures consistently below 22°F (30°C) are expected, the coolant mixture should be changed to a higher concentration. Consult a dealer for details for more information.
NOTICE
Reserve tank cap
1.5 ℓ engine models
Reserve tank cap
2.0 ℓ engine models
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you. Always let the engine and radiator cool down before removing the radiator cap.
WARNING
Pour the uid slowly and carefully so you do not spill any. Clean up any spills immediately; they can damage components in the engine compartment.
NOTICE
MA X
MINReserve tan k
Window Washer Fluid
Check the amount of window washer uid by looking
at the reservoir. If the washer uid level is low, ll the
washer reservoir.
Pour the washer uid carefully. Do not overow the
reservoir.
Canadian models
If the washer uid level is low, the washer level indicator or a message appears in the Driver Information Interface.
Do not use engine antifreeze or a vinegar/water solution in the windshield washer
reservoir. Antifreeze can damage your vehicle’s paint. A vinegar/water solution can damage the windshield washer pump.
NOTICE
Brake/Clutch* Fluid
The uid level should be between the MIN and MAX marks on the side of the reservoir.
We recommend using Honda Heavy Duty Brake Fluid DOT 3.
Pour the uid carefully.If the uid level is at or below the MIN mark, have a dealer inspect for leaks or worn brake pads as soon as possible.
The brake uid reservoir is also used for your vehicle’s clutch uid. As long as you keep the brake uid level as instructed above, there is no need for checking the clutch uid level.Brake uid marked DOT 5 is not compatible with your vehicle’s braking system and can cause extensive damage.
NOTICE
Brake reservoir
MINMAX
*if equipped

138 || 139
MAINTENANCE
MAINTENANCE
Checking the Battery
Check the battery terminals for corrosion monthly. For jump starting, see page 114.
The battery gives off explosive hydrogen gas during normal operation. A spark or ame can cause the battery to explode with enough force to kill or seriously hurt you. When conducting any battery maintenance, wear protective clothing and a face shield, or have a skilled technician do it. Battery posts, terminals, and related accessories contain lead and lead
compounds. Wash your hands after handling.
WARNING
Changing Wiper Blades
If the wiper blades leave streaks across the windshield, try cleaning them rst with a paper towel or soft cloth and wiper uid. If the wiper blade rubber has deteriorated, you should change the wiper blades.
1. Turn the vehicle off.
2. Hold the wiper switch in the MIST position, then turn the vehicle on. Both wiper arms lift up. Turn the vehicle off.
3. Lift both wiper arms.
4. Press and hold the tab, then slide the blade holder toward the base of the wiper arm.
5. Slide the wiper blade out from its holder by pulling the tabbed end out.
6. Slide the new wiper blade into the holder. The tab on the holder should t in the indent of the wiper blade.
7. Slide the wiper blade holder onto the wiper arm securely.
8. Lower the passenger side wiper arm rst, then the driver side.
Tab
Blade
Tab
Blade
TabBlade
Avoid dropping the wiper arm, as it may damage the windshield.
NOTICE
After replacing or reconnecting the battery, keep in mind:
•  Some systems are temporarily deactivated. Drive a short distance at 12 mph (20
km/h) or more, and the indicator(s) should go off.
•  The immobilizer system needs to be reset (see page 26).*
*Canadian models only
Holder
Holder
Cap

140 || 141
MAINTENANCE
MAINTENANCE
Tire Information
To safely operate your vehicle, your tires must be of the proper type and size, in good condition with adequate tread, and properly inated.
Inflation Guidelines
•  Properly inated tires provide the best combination of handling, tread life, and
comfort. Refer to the driver’s doorjamb label or the specications (see page 147) for the specied pressure.
•  Underinated tires wear unevenly, adversely affect handling and fuel economy,
and are more likely to fail from overheating.
•  Overinated tires make your vehicle ride harshly, are more prone to road hazards,
and wear unevenly.
•  Every day before you drive, look at each of the tires. If one looks lower than the
others, check the pressure with a tire gauge.
•  Measure the air pressure when tires are cold. This means the vehicle has been
parked for at least 3 hours, or driven less than 1 mile (1.6 km). If necessary, add or release air until the specied pressure is reached, and then calibrate the system
(see page 118). If checked when hot, tire pressure can be as much as 4–6 psi (30–40 kPa, 0.3–0.5 kgf/cm 2
) higher than checked when cold.
•  At least once a month or before long trips, use a gauge to measure the pressure in
all tires, including the spare. Even tires in good condition can lose 1–2 psi (10–20 kPa, 0.1–0.2 kgf/cm 2
) per month.
Inspection Guidelines
Every time you inate the tires, check for the following: •  Any damage to tires, including bumps, bulges, cuts, splits, or cracks in the side or
tread. Remove any foreign objects and inspect for air leaks. Replace tires if you see fabric or cord.
•  Uneven or excessive tread wear. Have a dealer check the wheel alignment.
•  Cracks or other damage around the valve stems.
Wear Indicators
The groove where the wear indicator is located is 1/16 inch (1.6 mm) shallower than elsewhere on the tire. If the tread has worn so low that the indicator is exposed, replace the tire. Worn out tires have poor
traction on wet roads.
Example of a wear indicator mark
Tire and Loading Information Label
The label attached to the driver’s doorjamb provides necessary tire and loading information.
Tire and Wheel Replacement
Replace your tires with radials of the same size, load range, speed rating, and
maximum cold tire pressure rating (as shown on the tire’s sidewall). Using tires of a
different size or construction can cause certain vehicle systems to work incorrectly.
It is best to replace all four tires at the same time. If that isn’t possible, replace the front or rear tires in pairs.
If you change or replace a wheel, make sure that the wheel’s specications match those of the original wheels. Using tires that are excessively worn or improperly inated can cause a crash in which you can be seriously hurt or killed.
Follow all instructions in this owner’s manual regarding tire ination and maintenance
.
WARNING
Original tire sizesNumber of people your vehicle can carryProper cold tire pressureTotal weight your
vehicle can carry (do not exceed)
Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.
Always use the size and type of tires recommended in the Owner’s Manual.
WARNING

142 || 143
MAINTENANCE
MAINTENANCE
Tire Service Life
The life of your tires is dependent on many factors, including driving habits, road
conditions, vehicle loading, ination pressure, maintenance history, speed, and environmental conditions (even when the tires are not in use). In addition to regular inspections and ination pressure maintenance, it is recommended that you have annual inspections performed once the tires reach ve years old. All tires, including the spare, should be removed from service after 10 years
from the date of manufacture, regardless of their condition or state of wear.
Winter Tires
If driving on snowy or frozen roads, mount all season tires marked “M+S”, snow tires,
or tire chains; reduce speed; and maintain sufcient distance between vehicles when
driving. For winter tires, select the size and load ranges that are the same as the original tires, and mount them to all four wheels.
Tire Chains
Because your vehicle has limited tire clearance, we strongly recommend using the following chains: For 215/55R16 tires:
Cable-type: Autotrac 0154505 For 215/50R17 tires:
Cable-type: Autotrac 0154005
Install tire chains on the front tires only. Mount chains as tightly as you can, and make sure that they do not touch the brake lines or suspension.
Using the wrong chains, or not properly installing chains, can damage the brake lines and cause a crash in which you can be seriously injured or killed.
Follow all instructions in this guide regarding the selection and use of tire chains.
WARNING
Traction devices that are the wrong size or improperly installed can damage your
vehicle’s brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle.
NOTICE
Tire Labeling
The tires that came on your vehicle have a number of markings. Those you
should be aware of are described below. Here is an example of what each marking means: P205/55R16 89H
P: Vehicle type (passenger)205: tire width in millimeters55: aspect ratio (tire section height as a percentage of its width) R: tire construction code (radial)16: rim diameter in inches89: load index (code indicating maximum load tire can carry) H: speed symbol (code indicating maximum speed rating)
Tire Identification Number (TIN)
The tire identication number (TIN) is a group of numbers and letters that look like the
example below. TIN is located on the sidewall of the tire.
Glossary of Tire Terminology
Cold Tire Pressure – The tire air pressure when the vehicle has been parked for at least three hours or driven less than 1 mile (1.6 km). Load Rating – The maximum load that a tire is rated to carry for a given ination pressure. Maximum Ination Pressure – The maximum tire air pressure that the tire can hold.
Maximum Load Rating – The load rating for a tire at the maximum permissible ination pressure for that tire. Recommended Ination Pressure – The cold tire ination pressure
recommended by the manufacturer.
Treadwear Indicators (TWI) – The projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread.
Tire size
Tire identication number (TIN)
Maximum tire load
Maximu m
tire pressure
Tire siz e
DOT B97R FW6X 2209 DOT: This indicates that the tire meets allrequirements of the U.S. Department ofTransportation .
B97R: Manufacturer’s identication markFW6X: Tire type code22 09: Date of Transportation

Year
Week

144 || 145
MAINTENANCE
MAINTENANCE
DOT Tire Quality Grading
The tires on your vehicle meet all U.S. Federal Safety Requirements. All tires are also
graded for treadwear, traction, and temperature performance according to Department
of Transportation (DOT) standards. The following explains these gradings.
Uniform Tire Quality Grading
Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
For example:
Treadwear 200
Traction AA
Temperature A
All passenger car tires must conform to Federal Safety Requirements in addition to these grades.
Treadwear
The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specied government test course. For
example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends
upon the actual conditions of their use, however, and may depart signicantly from
the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
Traction
The traction grades, from highest to lowest, are AA, A, B, and C. Those grades
represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specied government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
WARNING: The traction grade assigned to this tire is based on straight-ahead
braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
Temperature
The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specied indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds
to a level of performance which all passenger car tires must meet under the Federal
Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of
performance on the laboratory test wheel than the minimum required by law.
WARNING: The temperature grade for this tire is established for a tire that is properly
inated and not overloaded. Excessive speed, underination, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
Air Conditioning
To ensure proper and safe operation, the Society of Automotive Engineers (SAE J2845) recommends that the refrigerant system only be serviced by trained and certied technicians. Never repair or replace the air conditioning evaporator (cooling coil) with one removed from a used or salvaged vehicle. New replacement mobile air conditioning evaporators must be certied (and labeled) as meeting SAE Standard J2842.
Vented refrigerant is harmful to the environment. To avoid refrigerant from venting, never replace the evaporator with one removed from a used or salvaged vehicle.
NOTICE

146 || 147
SPECIFICATIONS
MAINTENANCE
Testing of Readiness Codes
Your vehicle has “readiness codes” as part of the onboard self-diagnostic system. Some
states refer to these codes as a test to see if your vehicle’s emissions components are
working properly. The codes may not be read if you go through the testing just after the battery has gone dead or been disconnected.
To check if they are set, turn the vehicle on without starting the engine. The malfunction
indicator lamp will come on for several seconds. If it goes off, the readiness codes are set. If it blinks ve times, the readiness codes are not set. If you are required to have your vehicle tested before the readiness codes are set, prepare the vehicle for retesting by doing the following:
1. Fill the gas tank to approximately 3/4 full.
2. Park the vehicle and leave the engine off for 6 hours or more.
3. Make sure the ambient temperature is between 40°F and 95°F (4°C and 35°C).4. Start the engine without touching the accelerator pedal, and let it idle for 20 seconds.
5. Keep the vehicle in Park (P) or Neutral for manual transmission. Increase the engine speed to 2,000 rpm, and hold it there for about 3 minutes.
6. Let the engine idle with your foot off the accelerator for 20 seconds.
7. Select a nearby, lightly traveled major highway where you can maintain a speed of 50 to 60 mph (80 to 97 km/h) for at least 20 minutes. Drive on the highway with
the vehicle in Drive (D) or 5th gear. Do not use cruise control. When trafc allows,
drive for 90 seconds without using the accelerator pedal. (Vehicle speed may vary
slightly; this is OK.) If you cannot do this for a continuous 90 seconds because of
trafc conditions, drive for at least 30 seconds, then repeat two more times (for a total of 90 seconds).
8. Drive in city/suburban trafc for at least 10 minutes. When trafc conditions allow, let the vehicle coast for several seconds without using the accelerator pedal or the brake pedal.
9. Park the vehicle and leave the engine off for 30 minutes.
The readiness codes are erased when the battery is disconnected, and set again only after several days of driving under a variety of conditions.
If a testing facility determines that the readiness codes are not set, you may be
requested to return at a later date to complete the test, or see your dealer.SPECIFICATIONS 1.5-L engine models
Vehicle
ModelHonda Civic 2-Doo r
No. of Passengers :
Fron t2
Rear 3
Tota l5
Weights:Gross Vehicle Weight Rating U.S.: 3,902 lbs (1,770 kg )
Canada: 1,770 kg
Gross Axle Weight
Rating (Front )U.S.: 2,105 lbs (955 kg )
Canada: 955 kg
Gross Axle Weight
Rating (Rear)U.S.: 1,808 lbs (820 kg )
Canada: 820 kg
Light Bulbs
*1:Models with halogen headlights*2: Models with LED headlights
Headlights (Low Beam)55W (H11) *1
LE D*2
Headlights (High Beam )60W (HB3)
*1
LE D*2
Fog Lights35W (H8
)
Parking/Da ytime Running Light sLED
Front Side Marker Lights3W
Front Turn Signal Lights 21W (Amber
)*1
LE D*2
Side Turn Signal Lights

(on Door Mirrors) *LE
D
Brake Light s2 1W
Rear Turn Signal Lights21W (Amber)
Rear Side Marker Lights LED
Back-Up Lights16 W
DEL
sthgilliaT
High-M ount Brake LightRear License Plate Light LEDTrunk Light5W
In terior Lights
Map Lights8 W
Ceiling Ligh t8 W
DEL
Engine and Fuel
Engine FuelDisplacemen t91.26 cu-in (1,496 cm 3
)
Spark Plug sN GKILZKAR8H8S
Fuel: TypeUnleaded gasoline, Pump octane number of 87 or highe r
Fuel Tank Capacity 12.39 US gal (46.9 ℓ)
Fluids
Air ConditioningRefrigerant TypeHFO-1234yf (R-1234yf)
Charge Quantity 13.2 – 15.0 oz (375 – 425 g)
Lubricant TypeRL85HM (POE)
Quantity 2.7 – 3.6 oz (77 – 103 g)
Washer Fluid
Tank CapacityU.S.: 2.6 US qt (2.5 ℓ) Canada: 4.8 US qt (4.5 ℓ)
Brake Fluid
Continuously Variable Transmission Fluid
SpeciedHonda Heavy Duty Brake Fluid DOT 3
SpeciedHonda HCF-2 Transmission Flui d
Capacity Change 3.9 US qt (3.7 ℓ)
Engine Oil
Engine Coolan
t
Recommended·Genuine Honda Motor Oil 0W-20 ·API Premium-grade 0W-20 detergent oi l
Capacity Change
3.4 US qt (3.2 ℓ)
Change including
lte r 3.7 US qt (3.5 ℓ)
SpeciedHonda Long Life Anti
freeze/Coolant Type 2
Ratio 50/50 with distilled wate r
Capacity1.34 US gal (5.09 ℓ)

(change including the remaining
0.2 US gal (0.75 ℓ) in the reserve tank )
Tires
RegularSize215/50R17 91HPressure psi (kPa [kgf/cm 2
])32 (220 [2.2] )
Compact Spar e Size
T125/80D16 97M
Pressure psi (kPa [kgf/cm 2
]) 60 (420 [4.2]
)
Wheel SizeRegular17 x 7JCompact Spar e16 x 4T

148 || 149
CUSTOMER INFORMATION
SPECIFICATIONS
2.0-L engine models
Vehicle
Model Honda Civic 2-Door
No. of Passengers :
Fron t2
Rear 3
Tota l5
Weights:Gross Vehicle Weight Rating U.S.: 3,737 lbs (1,695 kg )
Canada: 1,695 kg
Gross Axle Weight
Rating (Front )U.S.: 1,984 lbs (900 kg )
Canada: 900 kg
Gross Axle Weight
Rating (Rear)U.S.: 1,786 lbs (810 kg )
Canada: 810 kg
Light Bulbs
Headlights (Low Beam)55W (H11)Headlights (High Beam )60W (HB3)Parking/Daytime Running Light sLED
Front Side Marker Ligh t
Front Turn Signal Lights21W (Amber )
Brake Lights 21W
Rear Turn Signal Lights21W (Amber)
Rear Side Marker Lights LED
Back-Up Lights16W
DEL
sthgilliaT
High-M ount Brake LightRear License Plate Light LEDTrunk Light5W
In terior Lights
Map Light s8W
Ceiling Ligh t8 W
3W
DEL
Engine and Fuel
Engine FuelDisplacemen t121.76 cu-in (1,996 cm 3
)
Spark Plug s NG
K DILKAR7H11GS DILKAR7G11GS
DENSO DXE22HQR-D11 S
Fuel: TypeUnleaded gasoline, Pump octane number of 87 or highe r
Fuel Tank Capacity 12.39 US gal (46.9 ℓ)
Fluids
Air Conditioning *Refrigerant TypeHFO-1234yf (R-1234yf)
Charge Quantity 13.2 – 15.0 oz (375 – 425 g)
Lubricant TypeRL85HM (POE)
Quantity 2.7 – 3.6 oz (77 – 103 g)
Washer Fluid
Tank CapacityU.S.: 2.6 US qt (2.5 ℓ) Canada: 4.8 US qt (4.5 ℓ)
Brake/Clutch Fluid
Continuously Variable Transmission Fluid Manual Transmission Fluid
SpeciedHonda Heavy Duty Brake Fluid DOT 3
SpeciedHonda HCF-2 Transmission Flui d
Capacity Change 3.7 US qt (3.5 ℓ)
SpeciedHonda Manual Transmission Fluid (MTF )
Capacity Change 2.0 US qt (1.9 ℓ)
Engine Oil
Engine Coolan
t
Recommended·Genuine Honda Motor Oil 0W-20 ·API Premium-grade 0W-20 detergent oi l
Capacity Change
4.2 US qt (4.0 ℓ)
Change including
lte r 4.4 US qt (4.2 ℓ)
SpeciedHonda Long Life Anti
freeze/Coolant Type 2
Ratio 50/50 with distilled wate r
Capacity1.4 US gal (5.30 ℓ)
(change including the remaining
0.2 US gal (0.75 ℓ) in the reserve tank )
*
*
*
Tires
RegularSize215/55R16 93HPressure psi (kPa [kgf/cm 2
])32 (220 [2.2] )
Compact Spar e* Size
T125/80D16 97M
Pressure psi (kPa [kgf/cm 2
]) 60 (420 [4.2]
)
Wheel SizeRegular16 x 7JCompact Spar e16 x 4T
*if equipped
CUSTOMER INFORMATION
*if equipped
Learn about information specic to you as a Honda customer and how to get help.
Frequently Asked Questions/Troubleshooting
Below are some frequently asked questions and troubleshooting items that you may have about the vehicle. Q:
How do I set the vehicle clock?
A: For vehicles without navigation, see page 51. For vehicles with navigation, the
time is automatically set using GPS signals.Q: Why doesn’t the vehicle start when I press the ENGINE START/STOP button?*
A: The brake pedal must be pressed to start the engine.
Q: What is the AUTO* setting on my headlight lever?
A: When in the AUTO position, the vehicle’s exterior lights will automatically turn
on or off depending on the ambient lighting.Q: Why won’t the driver’s door unlock when I grab the door handle, even though 
  the keyless access remote is within range?* A: If you pull the handle too quickly, the system may not have time to conrm the
door is unlocked. Wait to hear a beep to conrm the door is unlocked. If you are
wearing gloves, the system may be slow to respond. Q: After my battery was disconnected or went dead, the audio system is asking for 
  a code. Where do I ind this? A: In most cases, you do not need to enter a code. Turn on the vehicle and the
audio system, and press and hold the power button until the system reactivates. Q: Why can’t I operate Pandora through the audio system?*
A: Audio may be streaming through Bluetooth Audio. Make sure Pandora mode
is selected and the phone cable is properly connected to the USB adapter
cable (if using). Some phones may prompt you to “Allow” a connection. Q: Is my phone compatible with  Bluetooth features?
A: Visit handsfreelink.com (U.S.) or www.handsfreelink.ca (Canada) to
check phone compatibility for Bluetooth Audio, Bluetooth HandsFreeLink,
and SMS text messaging.Q: Every time I press the Talk button, the system gives me voice prompts. Can I turn 
  these off?* A: From the Home screen, select SETTINGS. Select System, then select Voice
Prompt. Select Off.

150 || 151
CUSTOMER INFORMATION
CUSTOMER INFORMATION
Contact Us
Honda dealer personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to
your satisfaction, please discuss it with the dealership’s service manager or general
manager. If you are dissatised with the decision made by the dealership’s management, contact Honda Automobile Customer Service.
U.S. owners
American Honda Motor Co., Inc. Honda Automobile Customer Service
1919 Torrance Blvd.Mail Stop 500-2N-7A
Torrance, CA 90501-2746
Tel: (800) 999-1009
In Puerto Rico and the U.S. Virgin Islands
Bella International
P.O. Box 190816San Juan, PR 00919-0816
Tel: (787) 620-7546
When you call or write, please give us the following information: •  Vehicle Identication Number
•  Date of purchase
•  Odometer reading of your vehicle
•  Your name, address, and telephone number
•  A detailed description of the problem
•  Name of the dealer who sold the vehicle to you
Canadian owners
Honda Canada, Inc. Customer Relations180 Honda Blvd.Markham, ONL6C 0H9
Tel: (888) 946-6329Fax: (877) 939-0909e-mail: [email protected]
*if equipped
Honda Roadside Assistance
24-hour emergency road service is available to you in the United States and
Canada throughout your 3-year/36,000-mile warranty term. Services include
jump starting, at tire and lockout assistance, towing, and more (limitations apply). Call (866) 864-5211 (U.S.) or (800) 465-7587 (Canada).
Warranty Coverages
Below is a brief summary of the warranties covering your new vehicle.
New Vehicle Limited Warranty: Covers your new vehicle, except for the emissions
control system and accessories, against defects in materials and workmanship.
Emissions Control Systems Defects Warranty and Emissions Performance Warranty:
Covers your vehicle’s emissions control systems. Time, mileage, and coverage are conditional.
Seat Belt Limited Warranty: Covers seat belts that fail to function properly.
Rust Perforation Limited Warranty: Covers all exterior body panels that rust through
from the inside.
Accessory Limited Warranty: Covers Honda accessories.
Replacement Parts Limited Warranty: Covers all Honda replacement parts against
defects in materials and workmanship.
Replacement Battery Limited Warranty: Provides prorated coverage for a replacement
battery purchased from a Honda dealer.
Replacement Mufer Lifetime Limited Warranty: Covers a replacement mufer for the
duration of the ownership.
Restrictions and exclusions apply to all these warranties. See the Warranty Manual on the Owner Information CD or at owners.honda.com (U.S.) or myhonda.ca (Canada) for
complete descriptions of each warranty, including time, mileage, and other conditional limitations.
Your vehicle’s original tires are covered by their manufacturer. Tire warranty information can be found on the Owner Information CD or at owners.honda.com (U.S.) or
myhonda.ca (Canada).

152 || 153
VOICE COMMAND INDEX
VOICE COMMAND INDEX
Voice Portal Commands
When you press the Talk button, the Voice Portal screen appears. Say one of the options, and follow the system prompts.
Navigation Commands*
The system accepts these commands on most screens. You only need to press the
Talk button once for navigation commands.
Learn about all available voice commands to help you operate the vehicle. Available on vehicles with Display Audio.
Press the Talk button before you say a command.
VOICE COMMAND INDEX
• 
Phone call
•  Music search
•  Audio
•  Climate control
•  Navigation* • 
Voice setting
•  Voice help
•  What is today’s date?
•  What time is it?
•  View map
•  Find place
•  Find category
•  Find intersection
•  Recently found • 
Go home
•  Find address
•  Find city
•  Saved places
*models with navigation
**These commands toggle the function on and off, so the  command may not match your intended action.
Climate Control Commands*
The system accepts these commands on most screens. • Climate control on**
•  Climate control off**
•  Air conditioner on**
•  Air conditioner off**
•  Defrost on**
•  Defrost off** • 
Fan speed # (#: 1 to 7)
•  Temperature # degrees
(#: 57 to 87°F)
•  Temperature max heat
•  Temperature max cool
Phone Commands
The system accepts these commands on most screens. • Call by number
•  Call by name • 
Call (number)
•  Call (name)
Audio Commands*
The system accepts these commands on most screens. Audio volume levels cannot be controlled using voice commands.
FM/AM Radio Commands
• Audio on**
•  Audio off**
•  Radio FM
•  Radio AM
•  Radio tune to # FM (#: frequency,
e.g., 95.5)
•  Radio tune to # AM (#: frequency,
e.g., 1020)
•  Radio FM preset # (#: 1 to 12)
•  Radio AM preset # (#: 1 to 6)
SiriusXM Radio Commands
• Radio SXM
•  SXM channel # (#: 0 to 255)
•  SXM channel (channel name)
•  Radio SXM preset # (#: 1 to 12)
USB Commands
• USB
•  USB play
•  USB play track # (#: 1 to 30)
Pandora Commands (U.S. only)
• Pandora
•  Pandora play
iPod Commands
• iPod
•  iPod play
•  iPod play track # (#: 1-30)
Bluetooth Audio Commands
• Bluetooth audio play
(may not work on all phones)
•  Music search
•  List album (specify album)
•  List artist (specify artist)
•  List composer (specify composer)
•  List genre (specify genre)
•  List playlist (specify playlist)
•  Play album (specify album)
•  Play artist (specify artist)
•  Play composer (specify composer) • 
Play genre (specify genre)
•  Play playlist (specify playlist)
•  Play song (specify song)
•  What/Who am I listening to?
•  Who is this?
•  What’s playing?
•  Who’s playing?
•  What album is this?
Song By Voice Commands
Available for tracks stored on an iPod or USB device.
*models with navigation
**These commands toggle the function on and off, so the  command may not match your intended action.