power steering fluid HONDA INTEGRA 1994 4.G User Guide

Power Steering Hoses, Pipes
Replacement
NOTE:
. Connect each hosg to the corresponding pipe securg-
ly until it stops at the stopp€r on the pipe.
Install the clamp or ad,ustable clamp at the specified
distancs from the hose end as shown in the drawing.
. Add the power steering fluid to the specilied level on
the reservoir and check fo. leaks (see page 17-23).

Put ov6r the pipe untilthe hose stops at the$opper.
CAUTION: Chock all clampsfor doterioration 8nd dstor-
mation, and rsplacG with new onss if n6co33!ry,

Put over the pipe untilthehose stops at the stopper.
2.5 - 5.5 mm
{0.01 - 0.22 inl2.0 - 4.0 mm10.08 - 0.16 inl
2.5 - 5.5 mm10.01 - 0.22 in)
OUYI.fT HOSE11 N.m{1.1 kgl.m, 8 lbl.ftl
INI."ET HOSE
ABLE CLAMP
RETURN HOSE
coot"ER
CLAMPS
17 -34
CLAMPS

OUTI.TT HOSE
Power Steering Pump
Removal
NOTE: Before disconnecting the hoses from the pump,
place a suitable containsr under the car.
1. Drain the power steering fluid from the rsservoir.
2. Remove the belt by loosening the pump adjusting
bolt and mounting bolts.
3. Disconnect the inlet and outlet hoses from the
pump and plug the hoses.
NOTE; Take care not to spill ths tluid on the body
or parts. Wipe off spillod fluid at once.
4. Remove the pump mounting bolt, then remove th€
pump
NOTE: Do not turn the steering whesl with the
pump removeo
5. Wrap the opening of th€ pump with a piece of taps
to provent any foreign mat€rial. Se6 pags 17-44 for
oumD instsllstion,
tNt.€T HOSE
Disassembly
Pulley Removal
1. Drain the fluid from the pump.
2, Hold the stee.ing pump in a vise with soft iaws, and
hold the pulley with the specialtool and remove the
pulley nut and pulley.
CAUTION: Bo clrstul not to damage the pump
ho$ing with thr iaw3 of ths vise.
NOTE: Pullev nut has left-hand threads.
PULLEY NUT {Left-hand thread)
(cont'dl
17-35

Power Steering Pump
Reassembly
CAUTION: The power steering componsnts are mado of sluminum. Avoid dsmaging th€ componcnts during assombly,
NOTE:
. Clean the disassembled pans with a solvent and dry them with compressed air. Do not dip the rubber parts in a sofvent.
. Always replace the O-rings and rubber seals with new ones before assembly.. Apply recommended power steering fluid or steering grease (Honda P/N: 08733 - B070E) to the parts indicated in theassemblv procedures.
. Do not allow dust, dirt, or other foreign materials to enter the power steering system.. Replacethe pump asan assembly ifthe parts indicated with asterisk (*) are worn or damaged.
ROLLER5 x 26.8 mm
PUMP covEn /
."'MP cAM RING
, / .",or r*r,
^ / -e^urrae vrues / / sirx1.smm
\Al {ro pratesl I / o_nrNc
dA-h1//EZil*l///'^ee'ace
o-ntNGReplace.
16.8 x 1.9 mm O-RING
\A I {ro Platesl
,h$;@:",n1
i'"otr
/-V#mtt.m,1a|tt.fti// / / \E
RoLLER / |a.5 x ag.a mm / |68.5 x 1.9 mm Io-RING / INLET
Reptace.
I
.PUMP HOUSING
xf:.i'/pp@6{fr;ryDRIVE SHAFTPUMP SEALSPACERROLLER /1.5 x 49.8 mm /68.5 x 1.9 mmO-R|NG / INLET JO-INT
Replace.
I'PUMP ROTOR>ei
iiij:f:,ll-T;-,",,,, ll;il'- g--lblY""."*";
Replace. :
$+--- srntnc
E -5.8x1.9mm
22.r x r.9 mm o-RfNG ------t@-<'t o^::t:\-GReplace.Replace.
FLANGE BOLT'11 N.m 11.1 kg-m,8lb-ftI
17-40
CONTROL VALVE COVEN

Pump Rotor Installation
L Coat the lip of the new oil seal with steering grease
(Honda P/N 08733 - 8070E).
Install the new oil seal in the pump housing by
hand, then install the pump seal spacer.
NOTE: Insert the oil seal with its grooved side fac-
ing in.
Install the pump drive shaft assembly with the spe-
cialtool.
Install the 38 mm circlip with its tapered side facing
out,
3.
4.
DRIVER ATTACHMENT07947 - 6:1io50038 mmcrncuP
- DRIVE
fu'/'i,Ert\=zl4
I"J PUMP SEALIf /sprcen
x,tY -ot seal
-Gll
ATTACHMENT, 37 x ,r0
07t,16 - dt102d,
5. Coat the side plate grooves with the recommended
power steering fluid, then position the 16.8 x
1.9 mm and 54 x 1,9 mm O-rings on the side plate.
16.8 x 1.9 mmO.RING
5a x 1,9O.RING
l
SIDE PLATE
17-41
6. Install the preload spring in the pump housing.
7. Set the 4.5 x 49.8 mm roller in the 4.5 mm hole in
the pump housing.
8. Set the side plate over the roller and install it on the
pump housrng.
9. Set the 5 x 26.8 mm roller in the 5 mm hole in the
side plate.
5 x 26.8 mmROLLER
5 mm HOLE
SIDE PLATE
PRELOADSPRING
,1.5 mm
10.Assemble pump rotor to the drive shaft with the "o"
mark on the rotor facing upward.
Set the 10 vanes in the grooves in the rotor.
NOTE: 8e sure that the round ends of the vanes are
in contact with the sliding surface of the cam ring.
PUMP ROTOR
(cont'd)
11.

Power Steering Pump
Reassembly (cont'dl
Set the pump cam ring over the two rollers with the"8" mark on the cam ring upward.
Apply clean power steering fluid to the vanes and
cam ring.
Install the 68.5 x 1,9 mm O-ring on the pump cover.
Align the roller set holes in the pump cover with the
rollers.
'16. Align the projection on the pump housing and theprojection on the pump cover, and tighten the four
bolts.
20 N.m{2.0 kg .m, lil lbf.ftl
PUMP COVER
PROJECTIONS
13.
PUMP CAM RING
14.
15.
17 -42
17.
18.
13 x 1.9O.RING
E
Set the 13 x 1.9 mm O-ring on the inlet joint.
Install the inlet joint on the pump housing.
11.1 kgt.m. t lbf.ftl
INLET JOINT
T9

Flow Gontrol Valve Installation
1. Apply steering grease (Honda P/N 08733 - B070E) to
new O-rings.
2. Coat the flow control valve with clean power steer-
ing fluid.
3. Install the flow control valve, spring and control
valve cover on the pump housing.
4. Tighten the three control cover bolts.
FLOW CONTROLVALVE
SPRING
E;W
11 N.m {1.1 kgl.m,8lbtftl
2
Pulley Installation
1. Hold the steering pump in a vise with soft jaws.
CAUTION: Be careful not to damago the pump
hou3ing with the laws ol th€ vise.
2. Install the pump pulley as shown. Then install the
pulley nut.
Hold the pulley with the special tool and tighten the
pulley nut.
PULLEY NUT6ir N.m (6.5 kgt.m,47 lbt tt)
Check that the pump turns smoothly by turning the
pulrey.
PULLEY NUT
PULLEY
17-43

Power Steering Pump
lnstallation
1.Connect the inlet and outlet hoses. Tighten the
pump fiftings securely.
Loosely install the pump in the pump bracket with
mounting bolts.
11N.m11.r kgf.m, 8lbf.ftlOUTIIT HOUSE
INI.TT HOSEO-RINGReplaco.
ADJUSTINGBOLT
PUMP MOUNTING BOLTS2,r N.m {2.4 kgl.m. 17 lbf'ft}
Install the DumD belt.
CAUTION:
. Make surs that thg powor gtooring bslt i!
securgly on the grooyos of ths pulloy!.
. Do not get powor stggring fluid o. groaso in thg
power steering bclt or pulley trc6. Cloan oft 8ny
tluid or groa36 belore installation.
POWER STEERING BELT
PULI..EY
5.
Adjust the pump belt (see page 17-201.
Fill the reservoir to the uoDer level line.
NOTE; Take care not to spill the fluid on the body
and parts. Wipe off the spilled fluid at once.
GAUTION: Uro only Ganuino Honda Powor Stsor.
ing Fluid-V. Using othor tlui& 3uch a3 ATF or oiher
manutacturor's powor steering tluid will drm89e
the rystgm.
SYSTEM CAPACITY:
1.06litor (1.12 US.qt, 0.93 lmp.qt)
RESERVOIR CAPACIW:
0.79 litor (0.1|:| US.qt, 0.?0 lmp.qtl
UP?ER I.fVEL LINE
IEVEI LINE
- Start the engine, let it run at idle, then turn the
steering wheel lock-to-lock severaltimes to bleed
air from the system.
- Recheck the fluid level and add some if neces-
s8ry.
CAUTIONT Do not fill tha .63ervoir boyond th6
upp€r lcvol lino.
17 -44

Steering Gearbox
Removal
NOTE: Using solvent and a brush, wash any oil and dirt
off the valve body unit, its lines, and the end if the gear-
box. Blow dry with compressed air.
1. Drain the power steering fluid as described on page
17 -21.
2. Rsise the front of car, and support on safety stands
in the propsr locations (see section 1).
3. Remove the front wheels.
il. Removs the st€ering joint cove.,
SIEERING JOIi{T COVEB
Remove the steering joint lower bolt, and move thejoint toward the column.
NOTE: Lock the steering shaft with the ignition key
to retain the steering shaft position.
Remove the cotter pin trom the castle nut and
removo the nut.
Installthe 10 mm hex nut on the balljoint.
Be sure that ths 10 mm hex nut is flush with the ball
ioint pin end, or the threaded section of the ball
ioint pin might be damaged by the ball iointremover.
NOTE: Remove the ball joint using the Ball Joint
Remover, 28 mm {07MAC - 5100200}. Refer to page
l8-11 fot how to use the ball joint rcmover,
Separat€ the tie-rod ball joint and knuckle using the
soscialtool.
CAUTION: Avold d.maging th. blllloint boot.
BALL JOlt{T REMOVER. 28 mm07MAC - SLqt2|X)
Disconnect the shift linkage {MfI model: see section
13, A/[ model see section 14).
Disconnect the heated oxygen sensor (H02S) con-
ngctor, and separate the three way catalytic conver-
ter by removing the s€lf-locking nuts.
NOTE: Always replace the gaskets with new ones.
OXycEt{S€NSOnOONNECTOR SELF.LOCKINGNUT
{cont'd)IHREE WAYCA?ALYTIC CONVERTEN
8.
10.
HEATED
Replacs.
17-45

Reassembly
NOTE:
. Clean the disassembled parts with a solvent and dry them with compressed air. Do not dip the rubber parts in a sol-
vent.
. Always replace the O-rings and rubber seals with new ones before assembly.
. Apply power steering fluid or steering grease {HONDA P/N: 08733 - 8070E) to the parts indicated in the assembly pro-
cedures.
. Do not allow dust, dirt. or other foreign materials to enter the power steering system.
. Use the appropriate specialtools where necessary.
FLANGC BOLT20 N.m 12.0 kg{.m, lil lbt'ftl
CYLINDER PIPE A26 N'm (2.7 kgf.m, 20 lbf.ftl
VALVE I{OUSING
BOLI..ER BEARINGReplace.
VALVE SEAL RINGReplace.+-cncl|P
RACK GUIDE SCREW
S1IEVE SEAI RINGSReolace.
SITEVE
BACKUP RIM}
VALVE SEAL RINGRaplacs.
O.RINGReplac€.LOCKNUT
CYLINDER HOUSING
O-RINGBACKUP RING Replace.
\
PINION SHAFT
SHIMS
O-RINGReplace.
CYUNDER END SEALReolace.GEAR HOUSING
CYLINDER END SEALReplaco.O.RINGReplace.
I
x nd#$Y
IPISTON SEAL RINGReplace.
STEERING RACK
(cont'd)
17-53

Steering Gearbox
Reassembly lcont'd)
Vllvc Body Rea3sombly
1. Apply vinyl tape to the stepped portion of the pin-
ion shaft, and coat the surface of the vinyl tape with
the power steering tluid,
2. Install the backup ring with its tapered side as
shown below.
3. Coat the inside surface of the new valve oil seal
with power steering fluid.
4. Slide the valve oil seal over the pinion shaft. being
careful not to damage the sealing lip.
CAUTION: ln3tall the valve oil ssal with hs groovad
3ide tacing opposits the besring.
Vinyl trpolst.ppcd ponion,Tapered position.
Groove side.
VALVE OIL SEAL
Fit the new O-ring in the groove of the pinion shaft.
Then slide the new valve seal ring over the shaft
and groove in on the pinion shaft.
Remove the vinyl tape from the pinion shaft.
NOTE: Do not over - expand the valve saal ring.
S€aling
E
lip
PINION SHAFT
VALVE SEAL RING
17-54
7. Apply power steering fluid to the surface of the
valve seal ring that was installed on the pinion
shaft.
8. Apply power steering fluid to the inside of the spe-
cial tool. Set the larger diameter end of the special
tool over the valve seal ring.
9. Move the special tool up and down several times to
make the valve seal ring Jit in the pinion shaft.
10. Remove the special tool.
.11. Turn the special tool over and setthe smallerdiam-
eter end of the special tool over the valve seal ring.
Move the sDecial tool uD and down severai times to
make the valve seal ring snugly fit in the pinion
shaft.
VALVE SEAL RING
(H(ffi
Use the wider diameterend ot the specialtool first to makethe valve seal ringfit in the pinionshaft.
Make the valve seal ringsnugly fit in the.pinionshaft using the other end(smaller diameter end) ofthe specialtool.