Ignition harness HONDA INTEGRA 1994 4.G Workshop Manual

It the inspection for a particular code requires the test harness. remove the right door sill molding and kick panel. Pull
the carpet back to expose the ECM, Unbott the ECM cover. Turn the ignition switch off and connect the test harness
Check the system according to the procedure described for the appropriate code(s) listed on the following pages.
KICKPANEL
TESTHARNESSOTLAJ _PT3OlOA
DIGITAL MULTIMETERCommarcially ovribbla orKS-AHM-32-OO3
NOT USED
TERMINAL LOCATIONS(cont'd)
o oooooooooooo
ooooooooooooo
oo o oo ooo
oooooooo
ooooooooooo
ooooooooooo
11-37

PGM-FI System
Engine Control Module (ECM)
lB18B1 ongino onlyl
The Malfunction Indicator Lamp(MlL) n6v6. com6s on lovon follwo socondal aftor ignition istumed on.
lurn the ignition switch ON.
Inspect No. 15 {BACK-UP LIGHT}l1O A) luse in the underdashtuse/relay box.ls the low oil pressure light on?
- R€placo No. 'l5
IBACK-UP LIGHT)llo Al fuso.- Ropair short inYEL wiro botwoonNo. 15 (BACK-UP
LIGHT) {10 A) fusoano gauge 6$om-blv.
Turn lhe ignition switch OFF.
ls the fuse OK?
Connecl the test harness betweenthe ECM and connectors (seepag€ 11-37).Repair opon in YEL wiio botw6onNo.'15 IBACK-UP LIGHTI 110 A)luso and gaug6 assombly.
Turn the ignition switch ON.
- RsDlaco tho MIL bulb.- Ropair opon in GRN/ORN wi.ebetwoen ECM {A13} andgaug€ a$6mbly.
ls the MIL on?
Measure voltage between body
Oround and the tollowing termi-nafs individuallv: 423, 424.
Ropah op6n in BLK wirolsl bo-tw6en ECM and GlOl llocatod atthormostat housing) that hadmoro than 1.0 V.
ls there less than 1.O V?
Substituto a known-good ECMand rochgck, lf symptom/indica-tion go€s away, roplaco tho origi-nal ECM.
NOTE: lf this svmptom is intermittent. check for a loose fuse No. 15 (BACK
UP LIGHT, 1OA) in the under-dash Juse/relay box, a poor connection at ECM
terminal A13, or an intermittent open in the GRN/ORN wire between the ECM(A13) and the gauge assembly.
I A13
I| | o oooo oooooooo I oooo oooo I ooooool ooooooooooo I
G 10'l
11-42

Th. ll.lfunction Indicltor Lamp
lMlll at!y3 on o. cornaa on alt6ltwo aacond!.
Connect the SCS short connectorto th6 sorvice check connector(see page 11-34).
Turn the ignition switch ON.
Go to iolfdiagnostic Proceduros(se€ pago 11-34).Does the MIL indicate anv Oi-agnostic Trouble Code (DTC)?
Romove th€ SCS shon connectorlrom the service ch€ck connector.
Turn the ignition switch OFF.
Try to start the engine.
Connect the test harness betweenthe ECM and connectors (see
page 11-37).
Turn the ignition switch ON.
Measure voltage botween D4 (+ )terminal and D22 { - ) terminal.
connect the SCS shonconnector to servlcecheck connector.ls there approx. 5 V?
Ropair shon to body g.ound inBRN/WHT wire betwoon th6 ECMlD4) end sorvlco chock connocto?.Measure voltage be_tween D4 {+} terminaland body ground.
- R6pair open in BRN/WHT witobotwoon EcM lD4) and s6rv-ice chock connactor.- Repoir opon in BLK wiro bo-twoon 36rvi@ chock connectoaand G4Ol.
ls there approx. 5 V?
InsDoct ECU {ECM) 115 A) tuse inth6 undeFhood luse/relav box.
- Rsolaco ECU {ECM} (15 Allus€.- R6pair shon in YEL/WHT wilobotw6on ECU lEcMl 115 A)fuso and PGM-FI main rolay.
Remove the scs shortConnector from theservice check con-nector.
ls the luss OK?
NOTE:
a When there is no code stored, the MIL willstay on if the service check con-
nector is shorted.
a tf this svmotom is intermittent, check for:
- A loose ECM fuse (15A) in the under-hood tuse/relay box
- A loose No. 24 fuse (ACG) (ALT) ( 1 5A: B1 8B 1 engine, 2OA: B18C 1 en-
gine) in the under-dash fuse/relay box- An intermittent short in the BRN/WHT wire between the ECM (D4) and
the service check connector- An intermittent oDen in the BLK wire between the service check con-
nector and G4O1- An intermittent shon in the GRN/ORN wire between the ECM (A 13) and
the gauge assembly.- An intermittent short in the YELMHT wire between the ECM (D19) and
the MAP sensor- An intermittent short in the YEL/BLU wire between the ECM (D20) and
the TP sensor
o ooooo ooo ooo o loooooooo liii:$A$.Ps,l o oo ooo ooooo
o oooo ooo o o ooo I oooooooooooooooooo
D4 (+)
l"oo,o'.
D22 t-l
uu,l
'NOTE: After repair, disconnect the SCS ShortConnsctor, test drive the car, and recheckthe MIL
lor a code.
(cont'd)
(To page 1 'l -44)lTo page 1 1-44)
11-43

(From page 1 1-43)
Inspect the No. 24ACG {ALT) (lG)(15 A: 81881 engine, 2OA:818C1 enginel fuse in the under-dash fuse/relav box.
- R.pllr .hon in BLK|rEL wlr6batr.v€qr undariair luro/Fbybox lnd FGM-FI m.in .obv.- noebco lto. 24 ACG {lG) nLT)(15 A: 81881 ongin., 2OA:Bl8Cl onein.l tu!6.
ls the fuse OK?
Turn the ignition switch ON.
Disconnect the 3P connector oteach sensor one al a time:. MAP sensor. TP sensor
Rcplaoo thg lgnlor that caur6dth. llght to Oo out.Does the MIL remain ON?
Turn the ignition switch OFF.
connect the test harness.Disconnect the "D" connectorfrom th€ ECM only, not the mainwire harness (see page 11-37).
Check tor continuity betweenbody ground and D19, O2O ter-minals,
- Bapai? rhod ro body g.ound inYEL/WHT wi.e boiwoon ECM(Dl9) .nd MAP ..n3or.- R.p!k shon to body ground inYEL/BLU wire b.lwo6n ECM(O2Ol .nd TP 3on!or.
Reconnect all tho sensor con-necrors,Reconnect the "D" connector torhe ECM.
Turn the ignition switch ON.
{To page 11-45}
System
Control Module (ECMI (cont'dl
PGM-FI
Engine
Dt9I
I oooooooooo ooo I oooooooo I omoool o oooooooooo | |I ooooooooooooo I oooooooo 1o('oe(lo I ooooooooooo | |-lD2O I
\-.J
Continuity?
(From page 11-43)
Disconnect "A" con-nector from the ECM.
Subrtltute r knowngood ECM.nd rochock. ll lymptom/indics-tlon g@a rw!y, rephco tho origi-n.l ECM.
ls the MIL ON?
Ropair short to bodygiound in GRN/ORNwir6 botwoon tho ECMlA131 6nd MlL.
11-44

YES
PGM-FI
Heated
11-471
System
Oxygen Sensor Heater (cont'd)
YEL/BLK I+I ORI{/BLK (-I
wire side
HO2S44 N.m{4.5 kgt.m, 33 lbf.ft}
Check for continuity to bodyground on terminals 3 and 4of theHO2S.
Check for continuity between terminal4 and terminals 1 and 2 in-dividually.
Turn the ignition switch ON.
At the HO2S harness. measurevoltage between YEL/BLK 1f lteFminal and ORN/BLK l-) ter-mrnal.
Turn the ignition switch OFF.
Disconnect the "A" connectorfrom the ECM.Measure voltage between YEL/BLK l+) terminal and bodyground.
Turn the ignition switch ON.
At HO25 harness, measure vol-tage between YEL/8LK (+) termi-nal and ORN/BLK {-) terminal.
RoDair short in ORN/BLK wir6 b6tw6on ECM(A6l and HO2S.ls there baftery voltage?
Ropai. opon in YEL/BLKwire botwoan HO2S.nd PGM-FI main relav.
Turn the ignition switch OFF.Turn the ignition switch OFF.
11-48
{To page 11-49){To page 11-49}

* Monitor over a 5 minute Deriod unl6ssthe current drops below O.1A im-mediatelv.
BATTERYVOLTAGE?
L-E;
o ooooooooo ooo I ooooo oooooooooooooo
oo Qoooooooooo I oooooo ooooooooooooo
Connect the test harness "A"
connector to the main wire harness only, not the ECM (see page
1 1-371.
Connect an ammetet between ter-minals A6 {+ ) and 426 (- )
Turn the ignition switch ON.
ls the current less than0.1 A?.
Subrtitulo s known-good ECM.nd r.ch6ck. lf symptom/indica-tion goes away. roplaco tho origi-n.l ECM.
Connoct the test harn€ss "A"
connector to the main wire har-n6ss only. not th€ €CM {seo page't't-37).
Turn the ignition switch ON.
Measwe vohage bstween A6 {+ }tg.minal and A23 {-)terminal.
Ropsii op6n in ORN/BLK wiro bo-tw..n ECM {A6l and tho HO2S.
Subrtiluto s known{ood ECMlnd Echock. ll .ympiom/indic{-tirn god !way, '.pLc! f|e origl-h.l ECM.
11-49

PGM-FI System
rj-t
--t-.
Fuel Supply System
-+-lt@t- -t 13 |- ' "- - --i--
T,-n The Maltunction Indicator Lamp (MlL) indicares Diagnostic Trouble Code (DTC) 43: A problem in
- L:!-i - the Heated Oxygen Sensor (HO2S) circuit. or a probtem in the Fuel Supply System.
NOTE:. Use DIGITAL MULTIMETER.. U6e 2 Volt rang6.
o oooooo oooooo I oo oooooooooooooooooooQoo ooo ooooo I oooo ooooooooooooooo
426
JUMPER WIRE
o ooooo oooo ooo I oo oooooo Isdtcllodsl ooo ooooooooo oooo ooo oo ooo I oooo ooooooooooooooo
D14 {+l
I
426 t-l vohrgo rhould rl.n.t
| 0.4-0.5 V wh.n th..- ignirioo .wilch i! firdt|rtrod o.r, Itd docr!6ato b.low O.1 V in L..th6n two minutaa.
- Tho MIL h.s boen reportod on.- With rhe SCS short con-noctor connocted (soo paga1l-34), codo 43 b indlcat.d,
From codr I troebl.-lhoorlng lprgo 1146).
ls the code 43 accompanied bythe MIL and poor driveability?Go to Fuol Supply .y.t.m (|ecpag6 1t-971.
Do the ECM Reset ftocedure lseepage 11-35).
Connect the SCS short connectorto the service check connector{see page 'l1-34).
Start the engine. Hold the engineat 3,00O rDm with no load {A/T in
@or@ position, M/T in neutral)until the radiator Ian comes on,then let it idle for at least onemanute,
Intonnitl.nt t llure, tydom lr OKat thi. tim. lto.t drlv. mly b.nocaararyr.Chock lor poo? connactlona otloots wiro at C223 lloc.t.d atrlghl lhock towo.]. Cl13lHO2Sland ECM,
Raise the engine speed to 3,000rpm and hold that throttle positiontor at least one minute.Do not vary the throttle positioneven if the rpm drops.
Ooes the MIL blink and does itindicate code 43?
Turn the ignition swilch OFF.
Connect the test harness betweenthe ECM and conneclors {seepage 1 1-371.
With the ignition switch OFF, waitfor at least two minutes.
lnstall a jumper wire on the testharness between A6 and A26.
11-50
1To page 1 1-5'l l

Measure voltage between YEL/WHT {818C1 engine), YEL/RED(B188'1 engine) {+ ) terminal andbodv ground.
Measure voltage between YEL/WHT (818C1 engine), YEL/RED{B1881 engine) (+ } terminal andGRN/WHT (- ) terminal.
ls there approx. 5 V?
Repair opon in GRN/WHT wir6 botweonECM lD2l l and thoMAP sonsor,
Turn the ionition switch OFF.
ls there approi. 5 V?
Connect the test harness "D"
connector to the ECM only, nottothe main wire harness {see page11,37).
Turn the ignition switch ON.
Measure voltage betweon wHT/YEL (+ ) terminal and GRN/WHT{- } terminal.Measure voltage between D19{+} terminal and D21 {-}termrnat,
ls there approx. 5 V?
Bepair open in YEL/WHT wi.e be-tw€6n ECM lD19) and tho MAPaon30t.
ls there approx. 5 V?
Substitule s known-good ECMand rechock. ll symptom/indica'tion goes away, replac€ tho oiigi'nal ECM.Turn the ignition switch OFF.
Reconnecl the 3P connector tothe MAP sensor.
Connect the test harness betweenthe ECM and connector (see page1 1-371.
Turn the ignition switch ON.
11,52)
{To page 11-54}lTo page I l-54)
(cont'd)

PGM-FI System
Manifold Absolute Pressure
lFrom page 11-53)
{MAPI Sensor (cont'd)
(From paqe 1 1-53)
NO
M6asure voltage between D17{+) terminal and 021 (-}terminal.
ls there approx. 3 V?
Substituto 6 known{ood ECM.nd rach.ck. It symptom/indica-tion gooa away, Eplaco tho orlgi-nrl €CM.
Turn the ignition switch OFF.
Connect the test harness "D"
connector to the ECM only. not tothe main wire harness lsee page11-37).
Turn the ignition switch ON.
Measure voltage botwson Dl7(+) terminal and D21 {-}terminal.
R.p.lr opon or ahort in WHT|rELwi?o botw.on ECM {O17) and thoMAP senso..ls there approx. 5 V?
Substitute a known{ood ECMand rochsck. It prdcribed voltrgob now availablo, rophce trie origi-nal ECM.
approx. 3 v?
-D17 til D21 (-l
ooooooooooooo I oooooooo l l5oiE€tdl ooooooo
o oooo oooooooo ! ooooooooooooooooooo
11-54
'.---.-'

ECT SENSOR
GRN/BLU {-}
Turn the ignition switch ON.
Measure voltage betweon RED/WHT and body ground.
Measure voltage between RED/WHT {+}terminal and GRN/8LU(- ) terminal.ls there approx. 5 V?
ls there approx. 5 V?Ropai. opon in GRN/BLU wiro botwoon ECM(D221 and tho ECT36n3('r.Turn the ignition switch OFF.
Sub3tituto a known-good €CMand rochock. lf 3ymptom/indica-tion go6s away, roplaco the odgi-nal ECM.
Oisconnect the 22P connectortrom the Transmission ControlModule (TCM).
Turn the ignition switch ON.
ls there approx. 5 V7
Turn the ignition switch OFF andreconnect the connector to theTCM.
Connect the test harn€ss "D"
connector to the ECM only. not tothe main wire harness {see page11-37).
Turn the ignition switch ON.
Measure voltage between D13(+) terminal and D22 (-l ter-mlnal.
Repair opoa or shon inREO/WHT wiro botwoen ECMlDl3l and th6 ECT sonsor.R6pair shon in REO/WHT YYi..b6tw66n ECM {D131and TCM.
ls the.e approx. 5 V?
Substiluto a known-good ECMand rochock. ll lymptom/indica-tion goea 6wsy, replaco tho o.igi-n6l ECM,
A/T only
I
_i
11-59