Timing HONDA INTEGRA 1994 4.G Workshop Manual

[x] Cancel search | Manufacturer: HONDA, Model Year: 1994, Model line: INTEGRA, Model: HONDA INTEGRA 1994 4.G
Pages: 1413, PDF Size: 37.94 MB
HONDA INTEGRA 1994 4.G Workshop Manual INTEGRA 1994 4.G HONDA HONDA https://www.carmanualsonline.info/img/13/6067/w960_6067-0.png HONDA INTEGRA 1994 4.G Workshop Manual
Search: (oil reset, homelink, air bleeding, adding oil, wheel size, oil temperature)

Page 30 of 1413

HONDA INTEGRA 1994 4.G Workshop Manual - Automatic TransmissionSection 14Unit of length: mm (in) [t!tttltttt tt - MEASUREMENT STANDAND INEWI Wir. Di..o.D.Fr.. L.ngtht{o. of Colh SpringsRegulator valve spring ARegulator valve spring IStato

Page 33 of 1413

HONDA INTEGRA 1994 4.G Workshop Manual ll il Standards and Service Limits ElectricalSection 23 *1: Do not adiust the gap, replace spark plug it it is out of spec.*2r When using a new belt, adjust d€tl€ction or tension to new valu€s.

Page 64 of 1413

HONDA INTEGRA 1994 4.G Workshop Manual Cylinder Head/Valve Train 81881 engine Speciaf Tools .............6-2 Valve Clearance Adiustment ............6-3 Valve Seals Replacement (cylinder head removal not required) ..................... 6-5

Page 66 of 1413

HONDA INTEGRA 1994 4.G Workshop Manual 6-3 Valve Clearance Adjustment NOTE: . Valves should be adjusted cold; at a cylinder head temperature of less than 100F (38"C). Adjustment is the same for both intake and exhaust valves. . After adju

Page 68 of 1413

HONDA INTEGRA 1994 4.G Workshop Manual Valve Seals Replacement (cylinder head removal not requiredl NOTE: Cylinder head removal is not required in this procedure. The procodure shown below applies when using the in- car valve spring compre

Page 70 of 1413

HONDA INTEGRA 1994 4.G Workshop Manual Timing Belt lllustrated Index NOTE: . Refer to page 6-12 for positioning crankshaft and pulley before installing belt. . Mark the direction of rotation on the belt before removing. . Replace the rubbe

Page 72 of 1413

HONDA INTEGRA 1994 4.G Workshop Manual Timing Belt Inspection Remove the cylinder head cover. . Reler to page 6-3l when installing. Inspect the timing belt for cracks and oil or coolant soaking. NOTE: . Replace the belt if oil or coolant

Page 73 of 1413

HONDA INTEGRA 1994 4.G Workshop Manual Timing Belt Removal I NOTE: . Turn the crankshaft pulley so the No. 1 piston is attop d6ad center (TDC) before removing the belt (see page &12). a Inspect the water pump when removed the timingbolt {s

Page 74 of 1413

HONDA INTEGRA 1994 4.G Workshop Manual 1.Remove the cylinder head cover. . Refer to page 6-31 when installing. Remove the Dulley bolt and crankshaft pulley (see page 6-8). Remove the middle cover and the lower cover. NOTE: . Do not use the

Page 75 of 1413

HONDA INTEGRA 1994 4.G Workshop Manual Timing Belt Installation Install the timing belt in the revorce order of removal; Only key points are described here, NOTE: Cl€an the middle cover and lower cover beforeinstallation. L Position the
Page:   1-10 11-20 21-30 31-40 41-50 ... 60 next >
Search: (sat nav, trip computer, clock reset, fog light, service interval, wiring)