light HONDA S2000 2000 1.G Repair Manual

1. Open the hood.
If you need to change the high
beam headlight bulb on the left
side, remove the coolant reserve
tank from its holder by pulling it
straight up.
2. Remove the electrical connector
from
the bulb by squeezing the
connector to unlock the tab, then
slide
the connector off the bulb.
3. Remove the rubber weather seal
by pulling on the tab.
4. Unclip the end of the hold-down
wire from its slot.
Pivot it out of
the way and remove the bulb
socket.
5. Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Lights
6. Insert the socket back into the
headlight assembly. Make sure
the bulb is installed correctly by
looking through the headlight lens.
The pins on the base of the bulb
should fit in
the holes in the
headlight assembly.
Pivot the hold­
down wire back in place and clip
the end into the slot.
7. Install the rubber seal over the
back of
the headlight assembly.
Make sure it is right side
up; it is
marked
''TOP."
8. Push the electrical connector onto
the new bulb.
Turn on the headlights to test the
new bulb.
Maintenance 195

Lights
Replacing Front Tum Signal and
Side Marker Light Bulbs
1. If you are changing the bulb on
the driver's side, start the engine,
turn the steering wheel
all the way
to the right, and turn off the
engine.
If you are changing the
bulb on the passenger's side, turn
the steering wheel to the left.
196 Maintenance
2. Use a flat-tipped screwdriver to
remove the three holding clips
from the inner fender.
3. Pull the inner fender cover back.
4. Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
5. Pull the bulb straight out of its
socket.
6. Install the new bulb in the socket.
7. Insert the socket back into the
headlight assembly.
Turn it
clockwise to lock it
in place.
8. Test the lights to make sure the
new bulb is working.
9. Put the inner fender in place.
Install the two holding clips. Lock
each clip in place by pushing on
the center.

Replacing a Side Turn Signal Bulb 3. Pull the bulb straight out of its
1. Push the side turn signal assembly
forward until it pops out of
the
body.
2. Turn the bulb holder one-quarter
turn counterclockwise to remove it
from
the lens. socket.
Push the new
bulb straight into
the socket until it bottoms.
4. Put the bulb holder back into its
hole in
the lens, and turn it
clockwise until it locks.
5. Test the lights to make sure the
new bulb is working.
6. Put the side turn signal assembly
back into the body, back first.
Push on the front edge until it
snaps into place.
Lights
Maintenance 197

Lights
Replacing Rear Bulbs
1. Open the trunk.
2. Remove the fasteners from the
trunk lining. To remove a fastener,
push on
the center of the head
until it pops in. Then pull it out.
3. Pull the lining back.
198 Maintenance
4. Determine which of the four bulbs
is burned out: stop/taillight, back­
up light, turn signal, or side
marker. 5. Remove the socket by turning it
one-quarter
turn counterclockwise.
6. Remove the burned out bulb. To
remove the stop/taillight, back-up
or side marker light bulb, pull the
bulb straight out of its socket. To
remove the turn signal light bulb,
push it in and turn it
counterclockwise until it unlocks.

7. Install the new bulb in the socket.
8. Push the socket into the light
assembly and turn it clockwise
until it locks.
9. Test the lights to make sure the
new bulb is working.
lO.Install the trunk lining and secure
it with the fasteners. To reinstall a
fastener, reset the fastener by
pushing on the pointed end until it
pops back almost flush with the
fingers on the housing.
Put the
fastener
in the hole of the trunk
lining and push on the center until
it locks (the center is flush with
the head).
Lights
Maintenance 199

Lights
Replacing a Rear License Bulb
1. Insert a flat blade screwdriver
between
the left edge of the lens
and
the housing. The lens will
come down.
200 Maintenance
2. Pull the bulb straight out of its
socket.
Push the new bulb in until
it bottoms in
the socket.
3. Test the lights to make sure the
new bulb is working.
4. Put the lens back into the light
assembly, right side first.
Push on
the left edge until it snaps into
place.

Replacing an Interior Light Bulb
1. Remove the lens by carefully
prying on
the front edge of the
lens near both sides.
2. Remove the bulb by pulling it
straight out of its metal tabs.
3. Push the new bulb into the metal
tabs.
Snap the lens back in place.
Lights
Replacing the Trunk Light Bulb
1. Open the trunk. Pull down the
trunk light cover.
2. Remove the bulb by pulling it
straight out of its metal tabs.
3. Push the new bulb into the metal
tabs.
4. Push the cover back in place.
Maintenance 201

Storing Your Car
If you need to park your car for an
extended period (more than one
month), there are several things you
should
do to prepare it for storage.
Proper preparation helps prevent
deterioration and makes it easier to
get your car back on the road.
If
possible, store your car indoors.
• Fill the fuel tank.
• Change the engine oil and filter
(see page 159).
• Wash and dry the exterior
completely.
• Clean the interior. Make sure the
carpeting, floor mats, etc. are
completely dry.
• Raise the convertible top cover.
• Leave the parking brake off. Put
the transmission in Reverse.
202 Maintenance
• Block the rear wheels.
• If the car is to be stored for a
longer period, it should be
supported on jackstands so the
tires are off the ground.
• Leave one window open slightly (if
the car is being stored indoors).
• Disconnect the battery.
• Support the front wiper blade
arms with a folded towel or rag so
they
do not touch the windshield.
• To minimize sticking, apply a
silicone spray lubricant to
all door
and trunk seals. Also, apply a
vehicle body wax to the painted
surfaces that mate with the door
and trunk seals.
• Cover the car with a "breathable"
cover, one made from a porous
material such as cotton.
Nonporous materials, such as
plastic sheeting, trap moisture,
which can damage
the paint.
• If possible, run the engine for a
while periodically (preferably once
a month).
If you store your car for 12 months
or longer, have your Honda dealer
perform the inspections called for
in
the 24 months/30,000 miles (48,000
km) maintenance schedule as soon
as you take it out of storage (see
page
148 ). The replacements called
for
in the maintenance schedule are
not needed unless the car has
actually reached that time or mileage.

Exterior Care
Washing
Frequent washing helps preserve
your car's beauty. Dirt and grit can
scratch the paint, while tree sap and
bird droppings can permanently ruin
the finish.
Wash your car
in a shady area, not in
direct sunlight. If the car is parked in
the sun, move it into the shade and
let the exterior cool down before you
start.
Only use the solvents and cleaners
recommended
in this Owner's
Manual.
204 Appearance Care
NOTICE
Chemical solvents and strong cleaners
can
damar;e the paint, metal, and
plastic on your car.
• Rinse the car thoroughly with cool
water to remove loose dirt.
• Fill a bucket with cool water. Mix
in a mild detergent, such as
dishwashing liquid or a product
made especially for car washing.
• Wash the car, using the water and
neutral detergent solution and
sponge or soft cloth.
Start at a top
and work your way down. Rinse
frequently.
• Check the body for road tar, tree
sap, etc. Remove
these stains with
tar remover or turpentine. Rinse it
off immediately so it does not
harm the finish. Remember to re­
wax these areas, even
if the rest of the
car does not need waxing.
Do not use harsh chemicals to
remove stains from the
convertible top
or rear window.
Use a mild detergent/water
solution with a soft-bristle brush
on the top, and with a soft cloth on
the rear window.
• When you have washed and rinsed
the whole exterior, dry it with a
chamois or soft towel. Letting it
air-dry
will cause dulling and water
spots.
Make sure the top is completely
dry before you fold
it.
As you dry the car, inspect it for
chips and scratches that could allow
corrosion to start. Repair
them with
touch-up paint (see page
206 ).

Waxing
Always wash and dry the whole car
before waxing it. You should wax
your car, including the metal trim,
whenever water sits on
the surface
in large patches. It should form into
beads or droplets after waxing. You
should use a quality liquid or
paste wax. Apply it according to the
instructions on the container. In
general, there are two types of
products:
Waxes - A wax coats the finish and
protects it from damage by exposure
to sunlight, air pollution, etc. You
should use a wax on your Honda
when it is new.
Exterior Care
Polishes -Polishes and cleaner I
waxes can restore the shine to paint
that has oxidized and lost some of its
shine.
They normally contain mild
abrasives and solvents that remove
the top layer of the finish. You
should use a polish on your Honda
if
the finish does not have its original
shine after using a wax.
Cleaning tar, insects, etc. with
removers also takes off the wax.
Remember to re-wax those areas,
even
if the rest of the car does not
need waxing.
Appearance Care 205