headlights Hyundai Coupe 2003 User Guide

CONTROLS AND EQUIPMENT1- 43
SB380A1-E PARKING BRAKE The parking brake must always be set when the vehicle is to be left unattended. When the parking brake is applied, and the ignition key is at the "ON" position, the parking brake warning lampwill be illuminated. Before driving the vehicle, theparking brake must be fully released and thewarning lamp extinguished.
o To set the parking brake, apply the foot brake
and pull the parking brake lever up with the button depressed. Release the button whenthe brake is fully applied.
o To release the parking brake, apply the foot brake and pull up the parking brake leverslightly. Depress the button and lower thelever.
SB370A1-E INTERIOR REAR VIEW MIRROR The interior mirror is of the day/night type to enable the glare of headlamps from followingvehicles to be eliminated during night time driv-ing.The tab located at the bottom of the mirror shouldbe set to the position nearest the windscreen fornormal day time driving, and flipped towards therear of the vehicle to eliminate glare during nighttime driving. To adjust the field of vision, themirror may be moved by hand upon the mount-ing. NOTE: The mirror should always be adjusted prior tosetting the vehicle in motion.
B520A01GK
B520B01O-GAT DAY/NIGHT REAR VIEW MIRROR (Electric type) (Not all models) The electric type day/night inside rearview mirror automatically controls the glare of headlights ofthe car behind you. Adjust the rearview mirror tothe desired position.
B520B01GK
Sensor
HGK178

CONTROLS AND EQUIPMENT
1- 44
B550A02S-DAT HIGH-MOUNTED REAR STOPLIGHT
In addition to the lower-mounted rear stoplights on either side of the car, the high mounted rearstoplight in the centre of the rear window orinserted in the rear spoiler also comes on whenthe brakes are applied.
B360B01GK-GAT REAR FOG LIGHT SWITCH (Not all models)
HGK183
To turn on the rear fog lights, push the switch. They will come on when the headlights areturned on.
B550A01GK
A Type B Type
YB800A2-A FRONT FOG LIGHT SWITCH (Not all models) To turn on the front fog lights, push the switch. They will come on when the headlights are turnedon.
HGK142
C Type

OWNER MAINTENANCE 6-19
G290A01GK-EAT HEADLIGHT AIMING ADJUSTMENT
Before performing aiming adjustment, make sure of the following.
1. Keep all tyres inflated to the correct pressure.
2. Place the vehicle on level ground and press
the front bumper & rear bumper down severaltimes. Place vehicle at a distance of 118.1 in.(3m) from the test wall.
3. See that the vehicle is unloaded (except for full levels of coolant, engine oil and fuel, andspare tyres, jack, and tools).
4. Clean the head lights lens and turn on the headlight.
5. Open the bonnet.
6. Draw the vertical line (through the centre of each headlight beam pattern) and the hori-zontal line (through the centre of each head-light beam pattern) on the aiming screen.And then, draw a parallel line at 1.18 in. (30mm) under the horizontal line.
WARNING:The halogen bulb contains gas under pres-sure and if impacted could shatter, resultingin flying fragments. Always wear eye protec-tion when servicing the bulb. Protect the bulbagainst abrasions or scratches and againstliquids when lighted. Turn on the bulb onlywhen installed in a headlight. Replace theheadlight if damaged or cracked. Keep thebulb out of the reach of children and disposeof the used bulb with care.
Vertical aiming
G290A01GK
Horizontal aiming
Low Beam
Vertical aiming
G290A02GK
Horizontal aiming
High Beam
7. Adjust each cut-off line of the low beam to the
parallel line with a phillips screwdriver - VER- TICAL AIMING.
8. Adjust each cut-off line of the low beam to the each vertical line with a phillips screwdriver -HORIZONTAL AIMING.
G290B01GK-EAT Adjustment After Headlight Assembly Replacement
G290B02Y
Vertical line
Cut-off line Ground line
Horizontal line
LW
H
H "P"1.18 in.(30 mm)
If the vehicle has had front body repair and the headlight assembly has been replaced, the head-light aiming should be checked using an aimingscreen as shown in the illustration. Turn on theheadlight switch.
1. Adjust headlights so that main axis of light is parallel to centre line of the body and isaligned with point "P" shown in the illustration.
2. Dotted lines in the illustration show centre of headlights.

OWNER MAINTENANCE
6-20
SPECIFICATION: "H"Horizontal centre line of headlights from ground:Low Beam: 26.7 in. (679mm)High Beam: 26.5 in. (672mm) "W" Distance between each headlight centre : LowBeam: 47.3 in. (1,202mm)High Beam: 38.0 in. (966mm) "L" Distance between the headlights and the wallthat the lights are tested against : 118.11 in.(3,000 mm)