warning light Hyundai Coupe 2003 User Guide

FEATURES OF YOUR HYUNDAI
1- 42 B520A01A-AAT DAY/NIGHT INSIDE REARVIEW MIR- ROR
B520A01GK
Your Hyundai is equipped with a day/night inside rearview mirror. The "night" position is selectedby flipping the tab at the bottom of the mirrortoward you. In the "night" position, the glare ofheadlights of cars behind you is reduced. B520B01O-GAT DAY/NIGHT REAR VIEW MIRROR (Electric type) (If installed)
The electric type day/night inside rearview mirror automatically controls the glare of headlights ofthe car behind you. Adjust the rearview mirror tothe desired position.
B520B01GK
WARNING: Do not adjust or fold the outside rearviewmirrors while the vehicle is moving.This could result in loss of control, and anaccident which could cause death, seriousinjury or property damage.
Sensor
The outside rearview mirror heater is actuated in connection with the rear window defroster. Toheat the outside rearview mirror glass, push inthe switch for the rear window defroster. Therearview mirror glass will be heated for defrostingor defogging and will give you improved rearvision in inclement weather conditions. Push theswitch again to turn the heater off. The outsiderearview mirror heater automatically turns itselfoff after 15 minutes.
B510C01A-AAT FOLDING THE OUTSIDE REARVIEW MIRRORS
B510C01GK
To fold the outside rearview mirrors, push them towards the rear.The outside rearview mirrors can be folded rear-ward for parking in narrow areas.

FEATURES OF YOUR HYUNDAI
1- 44 B620A01S-AAT FRONT DOOR EDGE WARNING LIGHT A red light comes on when the front door is opened. The purpose of this light is to assist when you get in or out and also to warn passingvehicles.
B620A01GK2. Press the secondary latch lever up and lift the
hood.
3. Raise the hood by hand. When closing the hood, slowly close the hood and make sure it locks into place. WARNING:
o Always double check to be sure that the hood is firmly latched before driving away.If it is not latched, the hood could fly openwhile the vehicle is being driven, causinga total loss of visibility, which might resultin an accident.
o Do not move the vehicle with the hood in the raised position, as vision is obstructedand the hood could fall or be damaged.
B570A01GK-GAT HOOD RELEASE 1. Pull the release knob to unlatch the hood.
HGK106Hood Release Lever
HGK098
B550A01S-GAT HIGH-MOUNTED REAR STOP LIGHT In addition to the lower-mounted rear stoplights on either side of the car, the high mounted rearstoplight in the center of the rear window orinserted in the rear spoiler also lights when thebrakes are applied.
B550A01GK
A Type B Type C Type

FEATURES OF YOUR HYUNDAI 1- 45
B540A01F-AAT TAIL GATE Remote Tail Gate Release To open the tail gate without using the key, pull up
the lid release lever located on the driver's doorpanel.To close, lower the tail gate, then press down on
it until it locks. To be sure the tail gate is securelyfastened, always try to pull it up again. WARNING: The tail gate should always be kept complete-ly closed while the vehicle is in motion. If it isleft open or ajar, poisonous exhaust gasesmay enter the car resulting in serious illnessor death to the occupants. See additionalwarnings concerning exhaust gases on page2-1.
HGK124
WARNING: Gasoline vapors are dangerous. Before refu-
eling, always stop the engine and never allowsparks or open flames near the filler area. Ifyou need to replace the filler cap, use agenuine Hyundai replacement part.If you open the fuel filler cap during highambient temperatures, a slight "pressuresound" may be heard. This is normal and nota cause for concern.Whenever you open the fuel filler cap, turn itslowly.
HGK103
B560A01A-AAT REMOTE FUEL-FILLER LID RELEASE The fuel-filler lid may be opened from inside the vehicle by pulling up on the fuel-filler lid opener
located on the front floor area on the left side ofthe car. NOTE: If the fuel-filler lid will not open because ice
has formed around it, tap lightly or push onthe lid to break the ice and release the lid. Donot pry on the lid. If necessary, spray aroundthe lid with an approved de-icer fluid (do notuse radiator anti-freeze) or move the vehicleto a warm place and allow the ice to melt.
HGK105

FEATURES OF YOUR HYUNDAI
1- 46
B580A01A-AAT SUN VISOR
HGK145
Vanity mirror
Your Hyundai is equipped with sun visors to give the driver and front passenger either frontal orsideward shade. To reduce glare or to shut outdirect rays of the sun, turn the sun visor down. Avanity mirror is provided on the back of the sunvisor for the front passenger. NOTE: The Supplemental Restraint System (SRS)label containing useful information can befound on the back of each sun visor. WARNING: Do not place the sun visor in such a mannerthat it obscures visibility of the roadway,traffic or other objects.
HGK227
WARNING:
Do not close an open tailgate (rear hatch)
while a person(s) is sitting upright on the rearseat. The tailgate or tailgate glass may contactthe head of a person sitting upright on the rearseat. Closing the tailgate onto a person's headmay cause serious injuries, including death.
B540C01F-AAT To Unlock Using the Key To open the tail gate, insert the key and turn it clockwise to unlock. The tail gate compartmentlight illuminates when the tail gate is opened.
B540C01GK
B540D01GK-GAT When you close the tailgate
HGK226

FEATURES OF YOUR HYUNDAI
1- 48 B660D01E-GAT To Resume the Preset Speed
B660D01GK
The vehicle will automatically resume the speed set prior to cancellation when you push thecontrol switch upward to "RESUME (ACCEL)"position and release it, providing the vehiclespeed is above 40 km/h (25 mph). B660E01E-AAT To Reset at a Faster Speed
1. Push the control switch upward to "RESUME (ACCEL)" position and hold it.
2. Accelerate to desired speed and release the control switch. While the control switch is held, the vehicle will gradually gain speed.
B660C01E-GAT To Cancel the Cruise Speed Do one of the following:
o Pull the control switch toward the steeringwheel to "CANCEL" position.
o Depress the brake pedal.
o Depress the clutch pedal (Manual transaxle).
o Shift the selector lever to "N" position (Auto- matic transaxle).
o Decrease the vehicle speed lower than the memorized speed by 20 km/h (12 mph).
o Decrease the vehicle speed to less than 40 km/h (25 mph).
o Release the main switch.
WARNING: To avoid accidental cruise control engage-ment, keep the cruise control main switch offwhen not using the cruise control.
B660C01GK
B660B01E-GAT To Set the Cruise Speed
B660B01GK
1. Push in the cruise control main switch on the end of the barrel. The "CRUISE" indicator light in the instrument cluster will be illumi-nated. This turns the system on.
2. Accelerate to the desired cruising speed above 40 km/h (25 mph).
3. Push the control switch downward to "SET (COAST)" and release it.
4. Remove your foot from the accelerator pedal and the desired speed will automatically bemaintained.
5. To increase speed, depress the accelerator pedal enough for the vehicle to exceed thepreset speed. When you remove your footfrom the accelerator pedal, the vehicle willreturn to the speed you have set.

DRIVING YOUR HYUNDAI
2- 2 C040A01A-AAT KEY POSITIONS WARNING: The engine should not be turned off or thekey removed from the ignition key cylinderwhile the vehicle is in motion. The steeringwheel is locked by removing the key.
C020A01A-AAT BEFORE STARTING THE ENGINEBefore you start the engine, you should always:
1. Look around the vehicle to be sure there are
no flat tires, puddles of oil, water or other indications of possible trouble.
2. After entering the car, check to be sure the parking brake is engaged.
3. Check that all windows, and lights are clean.
4. Check that the interior and exterior mirrors are clean and in position.
5. Check your seat, seatback and headrest to be sure they are in their proper positions.
6. Close all the doors.
7. Fasten your seat belt and be sure that all other occupants have fastened theirs.
8. Turn off all lights and accessories that are not needed.
9. When you turn the ignition switch to "ON", check that all appropriate warning lights areoperating and that you have sufficient fuel.
10. Check the operation of warning lights and all bulbs when key is in the "ON" position. o To start the engine, insert the ignition key and
turn it to the "START" position. Release it assoon as the engine starts. Do not hold the keyin the "START" position for more than 15seconds.
NOTE:For safety, the engine will not start if the shiftlever is not in "P" or "N" Position (AutomaticTransaxle).
C030A01A-GAT COMBINATION IGNITION SWITCH To Start the Engine
o If your Hyundai is equipped with a manual transaxle, place the shift lever in neutral and depress the clutch pedal fully.
o If your Hyundai has an automatic transaxle, place the shift lever in "P" (park). o "START"The engine is started in this position. It will crankuntil you release the key. NOTE: Do not hold the key in the "START" positionfor more than 15 seconds.
o "ON" When the key is in the "ON" position, the ignition is on and all accessories may be turned on. If theengine is not running, the key should not be leftin the "ON" position. This will discharge thebattery and may also damage the ignition sys-tem.
o "ACC" With the key in the "ACC" position, some electri-cal accessories (radio, etc.) may be operated.
o "LOCK" The key can be removed or inserted in thisposition.To protect against theft, the steering wheel locksby removing the key. NOTE: To unlocking the steering wheel, insert thekey, and then turn the steering wheel and keysimultaneously.
C040A01E
LOCK
ACC
ON
START

DRIVING YOUR HYUNDAI 2- 3
C050A01A-AAT STARTING WARNING: Never run the engine in a closed or poorlyventilated area any longer than is needed tomove your car in or out of the area. Thecarbon monoxide gas emitted is odorlessand can cause serious injury or death.
C050B01A-GAT Normal Conditions:The Starting Procedure:
1. Insert key, and fasten the seat belt.
2. Depress the clutch pedal fully and place the
gearshift lever (manual transaxle) in neutralor the selector lever (automatic transaxle) in"P" (park) position.
3. After turning the ignition key to the "ON" position, make certain all warning lights andgauges are functioning properly before start-ing the engine.
WARNING:Be sure that the clutch is fully depressedwhen starting a manual transaxle vehicle.Otherwise, there is the potential to causedamage to the vehicle or injury to someoneinside or outside the vehicle as a result of theforward or backward movement of the ve-hicle that will occur if the clutch is not de-pressed when the vehicle is started.
4. Turn the ignition key to the "Start" position and release it when the engine starts.
C070C01A-AAT To remove the ignition key
1. Turn the ignition key to the "ACC" position.
2. Simultaneously push and turn the ignition key
counterclockwise from the "ACC" position tothe "LOCK" position.
3. The key can be removed in the "LOCK" position.
C050A01E
LOCK
ON
STARTC070C01E
LOCK ACC
ON
START

DRIVING YOUR HYUNDAI
2- 8 C130A01A-AAT GOOD BRAKING PRACTICES WARNING: Nothing should be carried on top of the shelfpanel behind the rear seat. If there were anaccident or a sudden stop, such objects couldmove forward and cause damage to the ve-hicle or injure the occupants.
o After being parked, check to be sure the
parking brake is not engaged and that the parking brake indicator light is out beforedriving away.
o Driving through water may get the brakes wet. They can also get wet when the car iswashed. Wet brakes can be dangerous! Yourcar will not stop as quickly if the brakes arewet. Wet brakes cause the car to pull to one
side. To dry the brakes, apply the brakeslightly until the braking action returns to nor-mal, taking care to keep the car under controlat all times. If the braking action does notreturn to normal, stop as soon as it is safe todo so and call your Hyundai dealer for assis-tance.
o Don't coast down hills with the car out of gear. This is extremely hazardous. Keep the car ingear at all times, use the brakes to slow down,then shift to a lower gear so that enginebraking will help you maintain a safe speed.
o Don't "ride" the brake pedal. Resting your foot on the brake pedal while driving can be dan-gerous because it can result in the brakes
overheating and losing their effectiveness. It
C090I01L-GAT CAUTION:
o Shift into "R" and "P" position only when
the vehicle has completely stopped.
o Do not accelerate the engine in reverse or any of the forward positions with the brakes applied.
o Always apply the footbrake when shifting from "P" or "N", to "R", "D"position.
o Do not use the "P" (Park) position in place of the parking brake. Always set the park-ing brake, shift the transaxle into "P" (Park)position and turn off the ignition whenyou leave the vehicle, even momentarily.Never leave the vehicle unattended whilethe engine is running.
o Check the automatic transaxle fluid level regularly, and add fluid as necessary.
C090N02O-AAT Good Driving Practices
o Never move the gear selector lever from "P" or "N" to any other position with the acceler- ator pedal depressed.
o Never move the gear selector lever into "P" when the vehicle is in motion.
o Be sure the car is completely stopped before you attempt to shift into "R".
o Never take the car out of gear and coast down a hill. This may be extremely hazardous.Always leave the car in gear when moving.
o Do not "ride" the brakes. This can cause them to overheat and malfunction. Instead, whenyou are driving down a long hill, slow down and shift to a lower gear. When you do this,engine braking will help slow the car.
o Slow down before shifting to a lower gear. Otherwise, the lower gear may not be en-gaged.
o Always use the parking brake. Do not depend on placing the transaxle in "P" to keep the carfrom moving.
o Exercise extreme caution when driving on a slippery surface. Be especially careful whenbraking, accelerating or shifting gears. On aslippery surface, an abrupt change in vehiclespeed can cause the drive wheels to losetraction and the vehicle to go out of control.
WARNING:
o Avoid high cornering speeds.
o Do not make quick steering wheel move- ments, such as sharp lane changes orfast, sharp turns.
o Always wear your seat belts. In a collision crash, un unbelted person issignificantly more likely to die than a per-son wearing a seatbelt.
o The risk of rollover is greatly increased if you lose control of your vehicle at high-way speeds.
o Loss of control often occurs if two or more wheels drop off the roadway and the driveroversteers to reenter the roadway.
o In the event your vehicle leaves the road- way, do not steer sharply. Instead, slowdown before pulling back into the travellanes.
o Never exceed posted speed limits.

DRIVING YOUR HYUNDAI 2- 9
also increases the wear of the brake compo- nents.
o If a tire goes flat while you are driving, apply the brakes gently and keep the car pointedstraight ahead while you slow down. When
you are moving slowly enough for it to be safeto do so, pull off the road and stop in a safeplace.
o If your car is equipped with an automatic transaxle, don't let your car creep forward. Toavoid creeping forward, keep your foot on thebrake pedal when the car is stopped.
o Use caution when parking on a hill. Engage the parking brake and place the gear selectorlever in "P" (automatic transaxle) or in first or
reverse gear (manual transaxle). If your car isfacing downhill, turn the front wheels into thecurb to help keep the car from rolling. If yourcar is facing uphill, turn the front wheels awayfrom the curb to help keep the car from rolling.If there is no curb or if it is required by otherconditions to keep the car from rolling, blockthe wheels.
o Under some conditions your parking brake can freeze in the engaged position. This ismost likely to happen when there is an accu-mulation of snow or ice around or near therear brakes or if the brakes are wet. If there isa risk that the parking brake may freeze,apply it only temporarily while you put thegear selector lever in "P" (automatic) or in firstor reverse gear (manual transaxle) and blockthe rear wheels so the car cannot roll. Thenrelease the parking brake. o Do not hold the vehicle on the upgrade with
the accelerator pedal. This can cause thetransmission to overheat. Always use thebrake pedal or parking brake.
C120A02A-AAT ANTI-LOCK BRAKE SYSTEM (If Installed) The Anti-Lock Brake System (ABS) is designed to prevent wheel lock-up during sudden brakingor on hazardous road surfaces. The ABS controlmodule monitors the wheel speed and controlsthe pressure applied to each brake. Thus, inemergency situations or on slick roads, ABS willincrease vehicle control during braking. NOTE: During ABS operation, a slight pulsation maybe felt in the brake pedal when the brakes areapplied. Also, a noise may be heard in theengine compartment while braking. Theseconditions are normal and indicate that theanti-lock brake system is functioning proper-ly. WARNING:Your ABS will not prevent accidents due toimproper or dangerous driving maneuvers.Even though vehicle control is improved dur-ing emergency braking, always maintain asafe distance between you and objects ahead.Vehicle speeds should always be reducedduring extreme road conditions.The braking distance for cars equipped withan anti-lock braking system may be longerthan for those without it in the following roadconditions.During these conditions the vehicle shouldbe driven at reduced speeds.
o Driving on rough, gravel or snow-covered
roads.
o Driving on with tire chains installed.
o Driving on roads where the road surface is pitted or has different surface height.
The safety features of an ABS equipped ve-hicle should not be tested by high speeddriving or cornering. This could endanger thesafety of yourself or others.

DRIVING YOUR HYUNDAI
2- 10 2) When the traction control system is oper-
ating properly, you can feel a slight pulsa- tion in the vehicle. This is only the effect ofbrake control and indicates nothing un-usual.
3) When the engine starts, a click is heard from the engine compartment; however,this is only the sound of traction controlbeing checked.
4) When moving out of the mud or fresh snow, pressing the accelerator pedal maynot cause the engine speed to increasedue to TCS operation.
C310D01O-AAT Indicators and Warning The indicators should illuminate when the igni- tion key is turned to ON or START but should goout after three seconds.If the indicators do not illuminate, or the TCS orTCS-OFF indicator does not go out after 3 sec-onds, have it checked by an authorized dealer. Should there be any unusual conditions in the device while driving, TCS-OFF indicator illumi-nates as a warning.If TCS-OFF indicator illuminates, pull your car toa safe place and stop the engine.Then, start the engine again to check if the TCS-OFF indicator goes out.
C300A03Y-GAT TRACTION CONTROL SYSTEM (TCS) (If installed)
HGK156A
CAUTION: When the TCS indicator blinks, SLIP controlhas been activated. It also means that theroad is slippery or your car is acceleratingexcessively. In this situation, gently releasefoot pressure from the accelerator pedal andmaintain moderate speed. WARNING: Traction control is only a driving aid; allnormal precautions for driving in inclementweather and on slippery road surfaces shouldbe observed.
On slippery road surfaces, the traction controlsystem (TCS) limits the drive wheels from spin-ning excessively, thus helping the car to acceler-ate. It also provides sufficient driving force andsteering performance as the car turns at acceler-ated speeds. SLIP Control Limits the drive wheels from spinning exces- sively during starting or while making accelerat-ed turns on slippery roads to avoid losing thedriving force of the front wheels. Driving hints TCS does not actively apply brakes. Be sure to decelerate the car sufficiently before enteringcurves. C310B01O-AAT TCS ON/OFF Mode When the TCS is running, the TCS indicator light in the instrument cluster will blink.If you turn the system off by pressing the TCSswitch, the TCS-OFF indicator light will come onand stay on. In the TCS-OFF mode, the SLIPcontrol will be deactivated. Adjust you drivingaccordingly. To turn the system back on, pressthe switch again. The TCS-OFF indicator lightshould go off. NOTE:
1) The TCS mode will automatically be turned
ON after the engine is turned off and re-started.