display HYUNDAI PALISADE 2022 Repair Manual

3-165
Convenience features
3
Rear View Monitor malfunction
and limitations
Rear View Monitor malfunction
When Rear View Monitor is not work-
ing properly, or the screen flickers, or
the camera image does not display
normally, have the vehicle inspected
by an authorized HYUNDAI dealer.
Limitations of Rear ViewMonitor
When the vehicle is stopped for a
long time in winter or when the vehi-
cle is parked in an indoor parking lot,
the exhaust fumes may temporarily
blur the image.
The rear view camera does
not cover the complete area
behind the vehicle. The driver
should always check the rear
area directly through the
inside and outside rearview
mirror before parking or back-
ing up.
The image shown on the
screen may differ from the
actual distance of the object.
Make sure to directly check
the vehicle's surroundings for
safety.
Always keep the rear view
camera lens clean. If the lens
is covered with foreign mate-
rial, it may adversely affect
camera performance and Rear
View Monitor may not operate
normally. However, do not use
chemical solvents such as
strong detergents containing
high alkaline or volatile organ-
ic solvents (gasoline, acetone
etc.). This may damage the
camera lens.
WARNING

3-169
Convenience features
3
Reverse Parking Distance Warningmay malfunction when:
- Heavy rain or water spray is pres-ent
- Water flows on the surface of the sensor
- Affected by another vehicle’s sen- sors
- The sensor is covered with snow
- Driving on uneven road, gravel roads or bushes
- Objects that generates ultrasonic waves are near the sensor
- Installing the license plate differ- ently from the original location
- The vehicle bumper height or ultrasonic sensor installation has
been modified
- Attaching equipments or acces- sories around the ultrasonic sen-
sors The following objects may not be
detected:
- Sharp or slim objects, such asropes, chains or small poles.
- Objects, which tend to absorb sensor frequency, such as
clothes, spongy material or snow.
- Objects smaller than 40 in. (100 cm) in length and narrower than 6
in. (14 cm) in diameter.
- Pedestrians, animals or objects that are very close to the ultra-
sonic sensors
Parking Distance Warning Indicators may be displayed differ-
ently from the actual detected loca-
tion when the obstacle is located
between the sensors.
Parking Distance Warning indica- tor may not occur sequentially
depending on vehicle speed or
obstacle shape.
If Reverse Parking Distance Warning needs repair, have the
vehicle inspected by an authorized
HYUNDAI dealer.

3-175
Convenience features
3
Forward/Reverse Parking DistanceWarning may malfunction when:
- Heavy rain or water spray is pres-ent
- Water flows on the surface of the sensor
- Affected by another vehicle’s sen- sors
- The sensor is covered with snow
- Driving on uneven road, gravel roads or bushes
- Objects that generates ultrasonic waves are near the sensor
- Installing the license plate differ- ently from the original location
- The vehicle bumper height or ultrasonic sensor installation has
been modified
- Attaching equipments or acces- sories around the ultrasonic sen-
sors The following objects may not be
detected:
- Sharp or slim objects, such asropes, chains or small poles.
- Objects, which tend to absorb sensor frequency, such as
clothes, spongy material or snow.
- Objects smaller than 40 in. (100 cm) in length and narrower than 6
in. (14 cm) in diameter.
- Pedestrians, animals or objects that are very close to the ultra-
sonic sensors
Parking Distance Warning Indicators may be displayed differ-
ently from the actual detected loca-
tion when the obstacle is located
between the sensors.
Parking Distance Warning indica- tor may not occur sequentially
depending on vehicle speed or
obstacle shape.
If Forward/Reverse Parking Distance Warning needs repair,
have the vehicle inspected by an
authorized HYUNDAI dealer.

3-176
Convenience features
Surround View Monitor will assist in
parking by allowing the driver to see
around the vehicle.
Detecting sensor
[1] : Surround-front view camera,
[2],[3] : Surround-side view camera (under the outside rearview mirror),
[4] : Surround-rear view camera
Refer to the picture above for the
detailed location of the detecting
sensors.
Surround View Monitor set-
tings
Camera settings
You can change Surround View Monitor ‘Display Contents’ or
‘Display Settings’ by touching the
setup icon ( ) on the screen
while Surround View Monitor is
operating, or selecting ‘Driver
Assistance →Parking Safety →
Camera Settings’ from the Settings
menu while the engine is on.
In the Display Contents, you can change settings for ‘Top View
Parking Guidance’, ‘Rear View
Parking Guidance’ and ‘Parking
Distance Warning’.
In the Display Settings, you can change the screen’s ‘Brightness’
and ‘Contrast’.
S SU U R RR RO O U UN ND D V V I IE E W W M M O ON NI IT T O O R R ( ( S S V V M M ) ) ( ( I IF F E E Q Q U UI IP P P PE ED D ) )
OLX2048060
OTM070213L
OLX2051135L
OLX2041432L
OLX2041431L

3-177
Convenience features
3
Top View Parking Guidance
When the ‘Top View ParkingGuidance’ is selected, parking guid-
ance is displayed on the right side of
the Surround View Monitor screen.
You may see the front top view or the rear top view when using Top
View Parking Guidance.
Rear View Parking Guidance
When the ‘Rear View ParkingGuidance’ is selected, parking
guidance is displayed in the rear
view.
The horizontal guideline of the Rear View Parking Guidance
shows the distance of 1.6 ft. (0.5
m), 3.3 ft. ( 1 m) and 7.6 ft. (2.3 m)
from the vehicle.
Parking Distance Warning
When the ‘Parking DistanceWarning’ is selected, parking dis-
tance warning is displayed on the
right side of the Surround View
Monitor screen.
The image will be displayed only when Parking Distance Warning is
warning the driver.
OTM070215L
■ Front top view
■Rear top view
OTM070214L
OTM070216LOTM070217L

3-178
Convenience features
Surround View Monitor opera-
tion
Operating button
Press the Parking/View button (1)to turn on Surround View Monitor.
Press the button again to turn off
the function.
Other view modes can be selected by touching the view icons (2) on
the Surround View Monitor screen.
When one of the infotainment sys- tem button (3) is pressed without
the gear in R (Reverse), Surround
View Monitor will turn off.Front view
The front image is displayed on the
screen when the gear is in N
(Neutral) or D (Drive) to assist in
parking. The front view has a top
view/front view/side view.
Operating conditions
When the gear is shifted from R(Reverse) to N (Neutral) or D
(Drive), the last set mode of front
view function will be selected.
Front view function will operate when the following conditions are
satisfied:
- While the infotainment systemscreen is being displayed, press
the Parking/View button (1)
briefly when the gear is in D
(Drive) or N (Neutral) and vehicle
speed is below 9 mph (15 km/h).
OLX2048060
OLX2048061L

3-179
Convenience features
3
Surround View Monitor Auto Onfunction will operate when the fol-
lowing conditions are satisfied:
- With ‘Driver Assistance →
Parking Safety → Surround View
Monitor Auto On’ selected from
the Settings menu, the front park-
ing assist view screen is dis-
played when Parking Distance
Warning warns the driver while
driving in D (Drive).Off conditions
Press the Parking/View button (1) again, the image will turn off.
When vehicle speed is above 9 mph (15 km/h) with the gear in D
(Drive), Surround View Monitor will
turn off and the screen will change
back to the previous infotainment
system screen. Although you drive
below 9 mph (15 km/h) again,
Surround View Monitor will not turn
on.
Press one of the infotainment sys- tem button (3), the screen will
change to the infotainment system
screen.
Shift the gear to P (Park), the image will turn off.
Rear view
The rear image is displayed on the
screen when the gear is in P (Park)
to assist in parking. The rear view
has a top view/rear view/side view.
Operating conditions
Shift the gear to R (Reverse), theimage will appear on the screen.
Press the Parking/View button (1) while the gear is in P (Park), the
image will appear on the screen.
Off conditions
The image cannot be turned offwhen the gear is in R (Reverse).
Shift the gear from R (Reverse) to P (Park), the image will turn off.
Press the Parking/View button (1) again while the gear is in P (Park)
with the image on the screen.

3-180
Convenience features
Rear View while driving
The driver is able to check the rear
view on the screen while driving, it is
to assist with safe driving.
Operating conditions
The engine is ON.
Press the Parking/View button (1)when vehicle speed is above 9
mph (15 km/h), Rear View while
driving will appear on the screen.
The ( ) icon is touched on the Surround View Monitor screen
when vehicle speed is below 9
mph (15 km/h), Rear View while
driving will appear on the screen.
Off conditions
Press the Parking/View button (1)again, the screen will change back
to the previous infotainment sys-
tem screen.
Select other view modes from the Surround View Monitor screen
when vehicle speed is below 9
mph (15 km/h), Rear View while
driving will turn off.
Press one of the infotainment sys- tem button (3), the screen will
change to the infotainment system
screen.
Shift the gear to P (Park), Rear View while driving will turn off.
Surround View Monitor mal-
function and limitations
Surround View Monitor malfunc-tion
When Surround View Monitor is not
working properly, or the screen flick-
ers, or the camera image does not
display normally, have the vehicle
inspected by an authorized
HYUNDAI dealer.
Limitations of Surround ViewMonitor
When the vehicle is stopped for a
long time in winter or when the
vehicle is parked in an indoor park-
ing lot, the exhaust fumes may
temporarily blur the image.
The screen may be displayed abnormally, and an icon will appear
at the top left side of the screen
under the following circumstances:
- The tailgate is opened
- The driver or front passengerdoor is opened
- The outside rearview mirror is folded

3-182
Convenience features
Blind-Spot View Monitor displays the
rear blind spot area of the vehicle in
the cluster when the turn signal is
turned on to help safely change
lanes.
Detecting sensor
[1], [2]: Surround-side view camera (camera located at bottom of the mirror)
Refer to the picture above for the
detailed location of the detecting
sensors.
Blind-Spot View Monitor set-
tings
Setting features
Blind-Spot View
With the engine on, select ‘Driver
Assistance →Blind-Spot Safety →
Blind- Spot View’ from the Settings
menu to turn on Blind-Spot View
Monitor and deselect to turn off the
function.
B B L LI IN N D D- -S S P P O O T T V V I IE E W W M M O ON NI IT T O O R R ( ( B B V V M M ) ) ( ( I IF F E E Q Q U UI IP P P PE ED D ) )
OLX2051136L
OLX2041433L/OLX2041434L
■ Left side ■Right side

3-183
Convenience features
3
Blind-Spot View Monitor oper-
ation
Operating switch
Turn signal lever
Blind-Spot View Monitor will turn on
and off when the turn signal is turned
on and off.
Blind-Spot View Monitor
Operating conditions
When the left or right side turn signal
turns on, the image in that direction
is displayed on the instrument clus-
ter.
Off conditions
When the turn signal turns off, theimage on the instrument cluster
will turn off.
When the hazard warning flasher is on, Blind-Spot View Monitor will
turn off, regardless of the turn sig-
nal status.
When other important warning is displayed on the instrument clus-
ter, Blind-Spot View Monitor may
turn off.
Blind-Spot View Monitor mal-
function
When Blind-Spot View Monitor is not
working properly, or the cluster dis-
play flickers, or the camera image
does not display normally, have the
vehicle inspected by an authorized
HYUNDAI dealer.
OIG046417
The image shown on the clus-
ter may differ from the actual
distance of the object. Make
sure to directly check the
vehicle's surroundings for
safety.
Always keep the camera lens
clean. If the lens is covered
with foreign material, it may
adversely affect camera per-
formance and Blind- Spot
View Monitor may not operate
normally.
WARNING