control mod Hyundai Terracan 2004 Owner's Manual

FEATURES OF YOUR HYUNDAI
1- 16 o When you return the seatback to its upright
position, always be sure it is locked into position by pulling and pushing on the top ofseatback.
WARNING:o The purpose of the fold-down rear seat back and the fold-up rear seat cushion isto allow you to carry more objects thancould be accommodated. Never allow pas-sengers to sit on the cargo area while thecar is moving. This is not a proper seatingposition and no seat belts are available foruse when the seat back is folded down.This could result in serious injury or deathin case of an accident or a sudden stop.Objects should not extend higher than thetop of the front seatbacks.This could allow cargo to slide forwardand cause injury or damage during sud-den stops.
o When you return the rear seatback to its upright position after being folded down,be careful not to damage the seatbelt web-bing or buckle. In addition, do not allowthe seatbelt webbing or buckle to getcaught or pinched in the rear seat.
o Do not allow passengers to fold down and up the seatback and seat cushion whilethe car is moving.
3. Pull the seat cushion release lever(2) up-ward, then fold up the seat cushion.
B090B02HP
(2)
B090B03HP
(3)
4. To secure the seat, hook the securing strap(3) under the seat cushion to the headrest stay of front driver and passenger seat.
5. To return the seatback and seat cushion to its normal position, reverse the above proce-dure. B095A02HP-GAT THIRD SEAT(For 7 Passengers) Adjusting Seatback Angle To recline the seatback, pull the seatback re- cliner control lever backwards, and release itafter the desired seatback angle is achieved.When you recline the seatback to desired posi-tion, always be sure it has locked into position.
HHP236-1

FEATURES OF YOUR HYUNDAI 1- 17
B095B02HP-1
(2)
B095B01HP-1
(1)
2. To fold down the seatback, pull the seatback recliner control lever(1), then push down the seatback.
B095B03HP-GAT Folding Rear Seatback and Seat cush- ion
1. Lower the headrest completely while press-
ing the lock knob (If installed). 3. Pull the seat cushion release knob(2) beside
the seat cushion, then fold the seat cushion sideways.
4. To secure the seat, fold the leg of the third seat(3) and hook the securing strap(4) underthe seat cushion to the assist handle.
(4)
(3)
HHP241-1
B095B04HP-1
5. Fix the seat belt buckle in the groove not to damage it. 6. To return the seatback and seat cushion to its
normal position, reverse the above proce- dure.
o When you return the seat cushion to its nor- mal position, always lower the leg of the thirdseat to lock the seat into position.
WARNING:
o The purpose of the fold-down rear seat back and the fold-up rear seat cushion isto allow you to carry more objects thancould be accommodated. Never allow pas-sengers to sit on the cargo area while thecar is moving. This is not a proper seatingposition and no seat belts are available foruse when the seat back is folded down.This could result in serious injury or deathin case of an accident or a sudden stop.Objects should not extend higher than thetop of the front seatbacks.This could allow cargo to slide forwardand cause injury or damage during sud-den stops.
o When you return the rear seatback to its upright position after being folded down,be careful not to damage the seatbelt web-bing or buckle. In addition, do not allowthe seatbelt webbing or buckle to getcaught or pinched in the rear seat.
o Do not allow passengers to fold down and up the seatback and seat cushion whilethe car is moving.

FEATURES OF YOUR HYUNDAI 1- 29
nated after blinking for approximately 6 seconds, or if it illuminates while the ve-hicle is being driven, please have an au-thorized Hyundai dealer inspect the pre-tensioner seat belts and SRS airbag sys-tem as soon as possible.
WARNING:
o Pre-tensioners are designed to operate only one time. After activation, pre-tensioner seat belts must be replaced. Allseat belts, of any type, should always bereplaced after they have been worn duringa collision.
o The pre-tensioner seat belt assembly mechanisms become hot during activa-tion. Do not touch the pre-tensioner seatbelt assemblies for several minutes afterthey have been activated.
o Do not attempt to inspect or replace the pre-tensioner seat belts yourself. Thismust be done by an authorized Hyundaidealer.
o Do not strike the pre-tensioner seat belt assemblies.
o Do not attempt to service or repair the pre- tensioner seat belt system in any manner.
o Improper handling of the pre-tensioner seat belt assemblies, and failure to heedthe warnings to not strike, modify, insp-ect, replace, service or repair the pre-tensioner seat belt assemblies may leadto improper operation or inadvertent acti-vation and serious injury.
The seat belt pre-tensioner system consistsmainly of the following components. Their locations are shown in the illustration.
1. SRS airbag warning light
2. Seat belt pre-tensioner assembly
3. SRS control module
B180B02S
Driver's airbag
1
3
Passenger's airbag
WARNING: To obtain maximum benefit from a pre-tensioner seat belt:
1. The seat belt must be worn correctly.
2. The seat belt must be adjusted to the correct position. NOTE:
o Both the driver's and front passenger's
pre-tensioner seat belts will be activatedin certain frontal collisions. The pre-tensioner seat belts can be activated aloneor, where the frontal collision is severeenough, together with the airbags.
o When the pre-tensioner seat belts are ac- tivated, a loud noise may be heard and finedust, which may appear to be smoke, maybe visible in the passenger compartment.These are normal operating conditionsand are not hazardous.
o Although it is harmless, the fine dust may cause skin irritation and should not bebreathed for prolonged periods. Wash yourhands and face thoroughly after an acci-dent in which the pre-tensioner seat beltswere activated.
CAUTION:
o Because the sensor that activates the SRS airbag is connected with pre-tensionerseat belt, the SRS airbag warning lighton the instrument panel will blink for ap-proximately 6 seconds after the ignitionkey has been turned to the "ON" position,and then it should turn off.
o If pre-tensioner seat belt is not working properly, this warning light will illuminateeven if there is no malfunction of the SRSairbag. If the SRS airbag warning lightdoes not illuminate when the ignition keyis turned to "ON" or if it remains illumi-
AIR
BAG
2

FEATURES OF YOUR HYUNDAI
1- 30 NOTE: Be sure to read information about the SRS onthe labels provided on the backside of thesun visor and in the glove box. WARNING:
o As its name implies, the SRS is designed
to work with, and be supplemental to, thedriver's and the passenger's three pointseat belt systems and is not a substitutefor them. Therefore, your seat belts mustbe worn at all times while the vehicle is inmotion. The airbags deploy only in certainfrontal impact conditions severe enoughto likely cause significant injury to thevehicle occupants.
o The SRS is designed to deploy the airbags only when an impact is sufficiently severeand when the impact angle is less than 30°from the forward longitudinal axis of thevehicle and will not deploy in side, rear orrollover impacts. Additionally, the airbagswill only deploy once. Thus, seat beltsmust be worn at all times.
o Front airbags are not intended to deploy in light collisions in which protection canbe provided by the seat belt alone.
o Always wear seat belts when driving or
riding in a motor vehicle.
B240A02Y-AAT SUPPLEMENTAL RESTRAINT (AIRBAG) SYSTEM (If Installed) Your Hyundai is equipped with a Supplemental
Restraint (Airbag) System. The indications of the
system's presence are the letters "SRS AIRBAG" embossed on the airbag pad cover in the
steering wheel and the passenger's side frontpanel pad above the glove box. The Hyundai SRS consists of airbags installed
under the pad covers in the center of the steeringwheel and the passenger's side front panel abovethe glove box. The purpose of the SRS is toprovide the vehicle's driver and/or the front pas-senger with additional protection than that of-fered by the seat-belt system alone, in case of afrontal impact of sufficient severity. Driver's Airbag
B240A01HP
B240C01HP
Rear impact
Side impact Rollover
o Front airbags are not intended to deploy in side-impact, rear-impact or rollover crashes. In addition, airbags will not de-ploy in frontal crashes below the deploy-ment threshold speed.
o The driver should sit back as far as possi- ble while still maintaining control of thevehicle. If you are sitting too close to theairbag, it can cause death or serious injurywhen it inflates.
o No objects should be placed over or near the airbag modules on the steering wheel,instrument panel, and the front passen-ger's panel above the glove box, becauseany such object could cause harm if thevehicle is in a crash severe enough tocause the airbags to deploy.
o If the airbags deploy, they must be re- placed by an authorized Hyundai dealer.

FEATURES OF YOUR HYUNDAI 1- 31
B240B02L
The airbag modules are located both in the center of the steering wheel and in the frontpassenger's panel above the glove box. Whenthe SRSCM detects a considerable impact to thefront of the vehicle, it will automatically deploy theairbags.
B240B03L
o Do not tamper with or disconnect SRS
wiring, or other components of the SRS system. Doing so could result in injury,due to accidental firing of the airbags orby rendering the SRS inoperative.
o Do not install a child restraint system in the front passenger seat position. A childrestraint system must never be placed inthe front seat. The infant or child could beseverely injured or killed by an airbagdeployment in case of an accident. Do notallow children to ride in the front passen-ger seat. If older children (teenagers andolder) must ride in the front seat, makesure they are always properly belted andthat the seat is moved back as far aspossible.
o For maximum safety protection in all types of crashes, all occupants including thedriver should always wear their seat beltswhether or not an airbag is also providedat their seating position to minimize therisk of severe injury or death in the eventof a crash. Do not sit or lean unnecessarilyclose to the airbag while the vehicle is inmotion. B240B02A-AAT SRS Components and Functions
B240B01L
The SRS consists of the following components:
- Driver's Airbag Module
- Passenger's Airbag Module
- Knee Bolster
- SRS Service Reminder Indicator (SRI)
- SRS Control Module (SRSCM)
The SRSCM continually monitors all elementswhile the ignition is "ON" to determine if a frontalor near-frontal impact is severe enough to re-quire airbag deployment. The SRS service reminder indicator (SRI) on the instrument panel will blink for about 6 secondsafter the ignition key is turned to the "ON" positionor after the engine is started, after which the SRIshould go out.

FEATURES OF YOUR HYUNDAI
1- 52
B420A02A-AAT CIGARETTE LIGHTER
For the cigarette lighter to work, the key must be in the "ACC" position or the "ON" position.To use the cigarette lighter, push it all the way intoits socket. When the element has heated, thelighter will pop out to the "ready" position.Do not hold the cigarette lighter pressed in. Thiscan damage the heating element and create afire hazard.If it is necessary to replace the cigarette lighter,use only a genuine Hyundai replacement or itsapproved equivalent. CAUTION: Do not use electric accessories or equipmentother than the Hyundai genuine parts in thesocket.
B410A01A-AAT INSTRUMENT PANEL LIGHT CONTROL (RHEOSTAT) (If installed)
B410A01HP
The instrument panel lights can be made brighter or dimmer by turning the instrument panel lightcontrol knob.
B420A01HPB500D01HP
4. MODE - Push "MODE" button to display a 12-
or 24-hour clock.
When the 12-hour clock is in use, the letters AM or PM appear with the time.
5. - The time is displayed on the LCD by pushing in on the switch and is turned off by pushing in on the switch again.
If your vehicle is equipped with the multimeter,see the page 1-46. B500D07O-AAT POWER OUTLET (If installed) These supply 12V electric power to operate electric accessories or equipment only when thekey is in the "ON" or "ACC" position. CAUTION: Do not use the power outlet to connect elec-tric accessories or equipment other thanthose designed to operate on 12 volts.

FEATURES OF YOUR HYUNDAI 1- 67
B670B01A-AAT Fan Speed Control (Blower Control)
B670B01HP
This is used to turn the blower fan on and off and to select the fan speed.
B670A01HP-GAT HEATING AND VENTILATION
B670A01HP
2
3
1
4
1. Fan speed control.This is used to turn the fan on and select the fan speed.
2. Air intake control. This allows you to select fresh outside air orrecirculation inside air.
3. Temperature control. This is used to turn the heating system on andoff and to select the degree of heating de-sired.
4. Air flow control. This is used to direct the flow of air.Air can be directed to the floor, dashboardoutlets, or windshield. Five symbols are usedto represent Face, Bi-Level, Floor, Floor-Defrost and Defrost air positions.
B670C01HP
The blower fan speed, and therefore the volume of air delivered from the system, may be con-trolled manually by setting the blower controlbetween the "1" and "4" position.
B670C01Y-AAT Air Intake Control This is used to select fresh outside air or recircu- lating inside air.
Fresh Recirculation
With the " " mode selected, air enters the vehicle from outside and is heated or cooledaccording to the other functions selected.With the " " mode selected, air from within thepassenger compartment is drawn through theheating system and heated or cooled accordingto the other functions selected.
o Pay particular attention to the driving con-
ditions whenever using the cruise controlsystem.
o During cruise-control driving with a manual transmission vehicle, do not shiftinto neutral without depressing the clutchpedal or the engine will be overrevved. Ifthis happens, depress the clutch pedal orrelease the main switch.
o During normal cruise control operation, when the "SET" button is activated orreactivated after applying the brakes, thecruise control will energize after approxi-mately 3 seconds. This delay is normal.
There are four controls for the heating and cool-ing system. They are:

FEATURES OF YOUR HYUNDAI
1- 68
NOTE:
o It should be noted that prolonged opera- tion of the heating system in " " modewill give rise to fogging of the windshieldand side windows and the air within thepassenger compartment will become stale.In addition prolonged use of the air condi-tioning with the " " mode selected mayresult in the air within the passenger com-partment becoming excessively dry.
o When the ignition switch is turned "ON", the air intake control will change to " "mode (regardless of switch position). Thisis normal operation.
Face-Level
Selecting the "Face" mode will cause air to be discharged through the face level vents.
Bi-Level
Air is discharged through the face vents and thefloor vents. This makes it possible to have coolerair from the dashboard vents and warmer air fromthe floor outlets at the same time.
B670D01L-AAT Air Flow Control
This is used to direct the flow of air. Air can be directed to the floor, dashboard outlets, or wind-shield. Five symbols are used to represent Face,Bi-Level, Floor, Floor-Defrost and Defrost airposition.
B670D01HP
HHP283
HHP283-1

FEATURES OF YOUR HYUNDAI 1- 69
B670E01HP
Cool
Warm
B670E02A-AAT Temperature Control This control is used to adjust the degree of heating or cooling desired.Floor-Level
Air is discharged through the floor vents, wind- shield defroster nozzle, side defroster nozzleand side ventilator.
Floor-Defrost Level
Air is discharged through the windshield defrost nozzle, the floor vents, side defroster nozzle andside ventilator.
HHP283-2
HHP283-3
Defrost-Level
Air is discharged through the windshield defrost nozzle, side defroster nozzle and side ventilator.If the "Defrost" mode is selected, the A/C will turnon automatically and "Fresh" mode will be acti-vated to improve windshield defrosting.
HHP283-4
If the "Floor-Defrost" mode is selected, the A/C will turn on automatically and "Fresh" mode willbe activated.

FEATURES OF YOUR HYUNDAI
1- 70
B690A02S-AAT HEATING CONTROLS
B690A01HP
For normal heating operation, set the air intake control to the fresh air ( ) position and the airflow control to the floor ( ) position. For faster heating, the air intake control should be set in the recirculate ( ) position. If the windows fog up, set the air flow control to the defrost ( ) position (The A/C will turn onautomatically and "Fresh" mode will be acti-
vated). For maximum heat, move the temperature con- trol to "Warm".
B700A01A-AAT BI-LEVEL HEATING
B700A01HP
Your Hyundai is equipped with bi-level heating controls. This makes it possible to have cooler airfrom the dashboard vents and warmer air fromthe floor outlets at the same time. To use thisfeature:
o Set the air intake control to the fresh air ( ) position.
o Set the air flow control at the bi-level ( ) position.
o Set the temperature control between "Cool" and "Warm".
B710A01A-AAT VENTILATION
B710A01HP
To operate the ventilation system:
o Set the air intake control at the fresh air ( ) position.
o To direct all intake air to the dashboard vents,
set the airflow control to the face ( ) position.
o Adjust the fan speed control to the desired speed.
o Set the temperature control between "Cool" and "Warm".