light INFINITI FX35 2004 Owner's Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2004, Model line: FX35, Model: INFINITI FX35 2004Pages: 4449, PDF Size: 99.66 MB
Page 586 of 4449
REFRIGERANT LINES
ATC-157
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2004 November 2004 FX35/FX45
Checking for Refrigerant LeaksAJS00163
Perform a visual inspection of all refrigeration parts, fittings, hoses and components for signs of A/C lubricant
leakage, damage and corrosion. A/C lubricant leakage may indicate an area of refrigerant leakage. Allow
extra inspection time in these areas when using either an electronic refrigerant leak detector or fluorescent
dye leak detector.
If dye is observed, confirm the leak with an electronic refrigerant leak detector. It is possible a prior leak was
repaired and not properly cleaned.
When searching for leaks, do not stop when one leak is found but continue to check for additional leaks at all
system components and connections.
When searching for refrigerant leaks using an electronic leak detector, move the probe along the suspected
leak area at 1 to 2 inches per second and no further than 1/4 inch from the component.
CAUTION:
Moving the electronic leak detector probe slower and closer to the suspected leak area will improve
the chances of finding a leak.
Checking System for Leaks Using the Fluorescent Leak DetectorAJS00164
1. Check A/C system for leaks using the UV lamp and safety goggles (J-42220) in a low sunlight area (area
without windows preferable). Illuminate all components, fittings and lines. The dye will appear as a bright
green/yellow area at the point of leakage. Fluorescent dye observed at the evaporator drain opening indi-
cates an evaporator core assembly (tubes, core or expansion valve) leak.
2. If the suspected area is difficult to see, use an adjustable mirror or wipe the area with a clean shop rag or
cloth, with the UV lamp for dye residue.
3. After the leak is repaired, remove any residual dye using dye cleaner (J-43872) to prevent future misdiag-
nosis.
4. Perform a system performance check and verify the leak repair with an approved electronic refrigerant
leak detector.
NOTE:
Other gases in the work area or substances on the A/C components, for example, anti-freeze, windshield
washer fluid, solvents and lubricants, may falsely trigger the leak detector. Make sure the surfaces to be
checked are clean.
Clean with a dry cloth or blow off with shop air.
Do not allow the sensor tip of the detector to contact with any substance. This can also cause false readings
and may damage the detector.
Dye InjectionAJS00165
(This procedure is only necessary when recharging the system or when the compressor has seized and was
replaced.)
1. Check A/C system static (at rest) pressure. Pressure must be at least 345 kPa (3.52 kg/cm
2 , 50 psi).
2. Pour one bottle (1/4 ounce / 7.4 cc) of the A/C refrigerant dye into the injector tool (J-41459).
3. Connect the injector tool to the A/C Low-pressure side service fitting.
4. Start engine and switch A/C ON.
5. When the A/C operating (compressor running), inject one bottle (1/4 ounce / 7.4 cc) of fluorescent dye
through the low-pressure service valve using dye injector tool J-41459 (refer to the manufacture′s operat-
ing instructions).
6. With the engine still running, disconnect the injector tool from the service fitting.
CAUTION:
Be careful the A/C system or replacing a component, pour the dye directly into the open system
connection and proceed with the service procedures.
7. Operate the A/C system for a minimum of 20 minutes to mix the dye with the system oil. Depending on the
leak size, operating conditions and location of the leak, it may take from minutes to days for the dye to
penetrate a leak and become visible.
Page 624 of 4449
AUDIO
AV-33
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
Terminals and Reference Value for A/C and AV SwitchAKS00A2B
Terminal No.
(Wire color)
ItemSignal
input/
outputCondition
Vo l ta g eExample of
symptom
+–Igni-
tion
switchOperation
1 (W/L) GroundBattery power
supply Input OFF – Battery voltageSystem does not
work properly.
2 (LG/R) GroundACC power-
supplyInput ACC – Battery voltageSystem does not
work properly.
3 (R/L) GroundIllumination
signal Input OFFLighting switch is
ONApprox. 12VA/C and AV
switch illumina-
tion does not
come on when
lighting switch is
ON. Lighting switch is
OFFApprox. 0V
4 (R/Y) GroundIllumination
control signalOutput ONIllumination control
switch is operated
by lighting switch in
1st or 2nd position.Changes between approx.0V
and approx.12VA/C and AV
switch illumina-
tion does not
come on when
lighting switch is
ON.
5 (B) Ground Ground – ON – Approx. 0V –
6 (B/R) GroundCommunica-
tion signal (+)Input/
OutputON –System does not
work properly.
7–Shield
ground –– – – –
8 (W/R) GroundCommunica-
tion signal (–)Input/
OutputON –System does not
work properly.
12 (R/G) GroundRemote con-
troller AInput ONPress MODE switch. Approx. 0V
Steering wheel
audio controls
do not function. Press SEEK UP
switch.Approx. 1.7V
Press VOL UP
switch.Approx. 3.3V
Except for above Approx. 5V
13 (G/W) GroundRemote con-
troller BInput ONPress POWER
switch.Approx. 0V
Steering wheel
audio controls
do not function. Press SEEK DOWN
switch.Approx. 1.7V
Press VOL DOWN
switch.Approx. 3.3V
Except for above Approx. 5V
14 (B/Y) –Remote con-
troller ground–– – –Steering wheel
audio controls
do not function.
SKIA0175E
SKIA0176E
Page 629 of 4449
AV-38
AUDIO
Revision: 2004 November 2004 FX35/FX45
Noise InspectionAKS00BMR
The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunction.
Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and opera-
tion of each piece of electrical equipment, and determine the cause.
NOTE:
The source of the noise can be found easily by listening to the noise while removing the fuses of electrical
components, one by one.
TYPE OF NOISE AND POSSIBLE CAUSE
Occurrence condition Possible cause
Occurs only when engine is
ON.A continuous growling noise occurs. The speed
of the noise varies with changes in the engine
speed.
Ignition condenser
A whistling noise occurs while the engine speed
is high. A booming noise occurs while the engine
is running and the lighting switch is ON.
Alternator
The occurrence of the noise is linked with the operation of the fuel pump.
Fuel pump condenser
Noise only occurs when various
electrical components are oper-
ating.A cracking or snapping sound occurs with the
operation of various switches.
Relay malfunction, radio malfunction
The noise occurs when various motors are oper-
ating.
Motor case ground
Motor
The noise occurs constantly, not just under certain conditions.
Rear window defogger coil malfunction
Open circuit in printed heater
Poor ground of antenna amplifier or
antenna feeder line
Mirror type film is attached on the rear win-
dow glass
After-market TV antenna and/or electrical
accessories such as radio are attached on
the rear window glass.
A cracking or snapping sound occurs while the vehicle is being driven, especially
when it is vibrating excessively.
Ground wire of body parts.
Ground due to incorrectinstallation of
parts.
Wiring connections or ashort circuit.
Page 646 of 4449
INTEGRATED DISPLAY SYSTEM
AV-55
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
INTEGRATED DISPLAY SYSTEMPFP:28090
System DescriptionAKS00BO5
A/C AND AV SWITCH SYSTEM
Refer to Owner′s Manual for A/C and AV switch operating instructions.
Using the A/C and AV switch at the center of the instrument panel, the controls of the following systems are
centralized:
Integrated display system (Drive computer, setting screen, etc.)
Auto A/C system
Audio system
PRECAUTION OF LCD MONITOR
In order to use LED for backlight of a display, by in car temperature, brightness may change. In low tem-
perature, the refreshing rate of the picture also becomes low because of the low response of the LCD
monitor. When passenger room becomes warm, however, the LCD recovers the normal display.
Backlight sometimes flickers or darkens according to the total consumption hours and the number of times
switched ON and OFF. In this case, display unit should be replaced. (Exchange only of backlight is impos-
sible.)
POWER SUPPLY AND GROUND
Power is supplied at all times
through 15A fuse (No. 32, located in fuse and fusible link box)
to display unit terminal 1, and
to A/C and AV switch terminal 1.
When ignition switch is in ACC or ON position, power is supplied
through 10A fuse [No. 6, located in fuse block (J/B)]
to display unit terminal 2, and
to A/C and AV switch terminal 2.
When ignition switch is in ON or START position, power is supplied
through 10A fuse [No. 12, located in fuse block (J/B)]
to display unit terminal 3.
Ground is supplied
to display unit terminals 6 and 15, and
to A/C and AV switch terminal 5
through body grounds M35, M45 and M85.
Page 649 of 4449
AV-58
INTEGRATED DISPLAY SYSTEM
Revision: 2004 November 2004 FX35/FX45
SETTING SCREEN
Setting of electric status can be changed by A/C and AV switch. The signal is sent to BCM through display
unit to change vehicle electric system setting.
Display unit is communicating with driver seat control unit.
Pressing “SETTING” switch once cycles display from DISPLAY→LANGUAGE→BEEP SET→SERVICE
ALERT→PERSONALIZED SETTINGS MENU→DISPLAY OFF→DISPLAY.
Using the joystick, setting of each item will become possible.
Adjustable Vehicle Status
NOTE:
Setting in factory shipment is ON.
Setting itemsSetting varia-
tionsInitial
settingOperation
DISPLAY ON/OFF ON It switches displayed/Non-displayed of the screen.
LANGUAGEENGLISH/
FRANCAIS– It switches displayed language.
BEEP SET ON/OFF ONIt selects beep sound ON/OFF during switch operation. How-
ever, even if beep is set OFF, beep for NO OPERATION and
for screen interception are not reset.
SERVICE ALERT ON/OFF OFFIt switches displayed/Non-displayed of alert indication.
When the setting is ON, if engine oil or tire rotation will be
replace distance, alert is displayed.
When the setting is OFF, alert is not displayed.
PERSONALIZED
SETTING MENUSLIDE BACK DR
SEAT ON EXITON/OFF
ON
NoteThe driver’s seat automatically moves back and returns to
the original position for exceptional ease of exit and entry.
(Models with automatic drive positioner.)
LIFT STEERING
WHEEL ON EXITON/OFF
ON
NoteThe steering column automatically tilts up and returns to the
original position for exceptional ease of entry and exit. (Mod-
els with automatic drive positioner.)
REMOTE UNLOCK
DOOR LOGICDR-1ST/ALL DR-1STThis key can switch the unlock doors of the 1st unlocking
operation as follows:
Only the driver side door⇔All the doors
HORN CHIRP WITH
REMOTEON/OFF ONThis key changes the horn chirp mode occurring when press-
ing the LOCK button on the keyfob.
LAMPS FLASH
WITH REMOTEALL/LOCK/
UNLOCK/OFFALLThis key changes the hazard indicator flash mode occurring
when pressing the LOCK or UNLOCK button on the keyfob.
AUTO RE-LOCK
TIME5m/1m/OFF 1mThe length of auto door re-lock time can be set. Select the
“Auto Re-Lock timer” key, then move the joystick to adjust the
time.
AUTO HEADLAMP
SENSITIVITYLEVEL 1/2/3/4LEVEL
2Automatic light illumination can be set as desired. Select the
“Auto Headlamp Sensitivity” key, then move the joystick to
the left (lower) or right (higher).
AUTO HEADLAMP
OFF DELAYOFF/30/45/60/
90/120/150/
180 SEC45 SECThis key can control how long it takes the automatic turn off
timer to extinguish the headlamps in “AUTO” position. Select
the “Auto Headlamp Off Delay” key, then move the joystick to
the left or right to adjust the timer.
SPEED SENSING
WIPER INTERVALON/OFF ONThis key turns on and off the driving speed dependent inter-
mittent wiper function.
CONFIRM RESET
SETTINGSYES/NO NOWhen this key is selected and turned on using the “ENTER”
button, all settings mode by PERSONALIZED SETTINGS will
return to the initial conditions.
Page 650 of 4449
INTEGRATED DISPLAY SYSTEM
AV-59
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
D/N SCREEN
Turning on “DAY/NIGHT” switch, DAY MODE or NIGHT MODE
is indicated for present mode.
If press “DAY/NIGHT” again when display adjustment lumi-
nance, change DAY-NIGHT(NIGHT-DAY) mode (screen of
adjustment luminance).
As follows:
Press “PREV” or not operate for 10sec. when displayed screen
of adjustment luminance, back to default screen (same mode).
Can adjust luminance by “DISP” switch. Light can be adjusted by pressing “+” (bright) or “–” (dark).
Adjustment range is a 12 stage (MIN to MAX) and default set value is 10 (DAY) and 4 (NIGHT).
WARNING INDICATIONS
When BCM receives warning signal from some control units or sensors, then combination meter warning lamp
is illuminated.
Then BCM sends warning signal to display unit warning indications on the screen.
AV COMMUNICATION LINE
Display unit is controlled by the following unit with AV communication line.
A/C and AV switch
NOW Change display
DAY DAY→NIGHT→DAY→·····
NIGHT NIGHT→DAY→NIGHT→·····
SKIA5920E
Warning indicatorsWarning lamps in
instrument panelWarning detection and cancel conditions Cases of malfunction
DOOR OPEN DoorDetection
conditionVehicle is running [approx. 3.5 km/h (2 MPH) or
faster] and door ajar of any of the doors is detected.
Door is open
Cancel
conditionVehicle is stopped and all the doors close.
Page 663 of 4449
AV-72
INTEGRATED DISPLAY SYSTEM
Revision: 2004 November 2004 FX35/FX45
Terminals and Reference Value for Display UnitAKS00BOD
Terminal No.
(Wire color)
ItemSignal
input/
outputCondition
VoltageExample of
symptom
+–Ignition
switchOperation
1 (W/L) GroundBattery power
supplyInput OFF - Battery voltageSystem does not
work properly.
2 (LG/R) GroundACC power
supplyInput ACC - Battery voltageSystem does not
work properly.
3 (G/R) Ground Ignition signal Input ON - Battery voltageA/C operation is
not possible.
Vehicle informa-
tion setting is not
possible.
4 (R/L) GroundIllumination
signalInput OFFLighting switch is
ON .Approx. 12VScreen does not
switch to night-
time mode after
the lighting switch
is turned ON. Llighting switch is
OFF.Approx. 0V
6 (B) Ground Ground - ON - Approx. 0V -
7 (R/G) GroundVehicle speed
signal (8-pulse)Input ONWhen vehicle
speed is approx.
40 km/h (25 MPH)Drive computer
item is not dis-
played correctly.
8 (LG) Ground Audio TX Output ONOperate audio
volume.Audio does not
operate properly.
9 - Shield ground - - - - -
10 (B/Y) Ground Audio RX Input ONOperate audio
volume.Audio does not
operate properly.
11 (B/R) GroundCommunica-
tion signal (+)Input/
outputON -System does not
work properly.
12 - Shield ground - - - - -
PKIA1935E
SKIA4402E
SKIA4403E
SKIA0175E
Page 669 of 4449
AV-78
INTEGRATED DISPLAY SYSTEM
Revision: 2004 November 2004 FX35/FX45
Trouble Diagnosis Chart by SymptomAKS00BOI
Symptom Check item
No screen is shown.
Display unit power supply and ground circuit. Refer to AV- 7 9 , "Power Supply
and Ground Circuit Check for Display Unit" .
Display unit
Screen does not switch to nighttime mode after the
lighting switch is turned ON.
Illumination signal. Refer to AV-81, "Illumination Signal Inspection" .
Display unit
TRIP and FUEL ECON screen do not appear.
Ignition signal. Refer to AV- 8 2 , "Ignition Signal Inspection" .
Display unit
Trip odometer (DIST) is not added up.
Average vehicle speed (AVG) is not displayed.
Vehicle speed signal. Refer to AV- 8 0 , "Vehicle Speed Signal Inspection" .
Display unit
Average fuel consumption (AVG) is not displayed.
Vehicle speed signal. Refer to AV- 8 0 , "Vehicle Speed Signal Inspection" .
CAN communication line. Refer to AV- 8 5 , "CAN Communication Line Inspec-
tion" .
Display unit
Distance to empty (DTE) is not displayed.
Check if speedometer operates. If it does not operate, go to DI-17, "Vehicle
Speed Signal Inspection" .
Check if fuel gauge operates. If it does not operate, go to DI-20, "Fuel Level
Sensor Signal Inspection 1" .
CAN communication line. Refer to DI-22, "Communication Line Inspection" .
Display unit
Tire pressure is not displayed.
Ignition signal. Refer to AV- 8 2 , "Ignition Signal Inspection" .
Low tire pressure warning control unit. Refer to WT-17, "Self-Diagnosis" .
CAN communication line. Refer to DI-22, "Communication Line Inspection" .
Display unit
Door warning screen does not appear.
Ignition signal. Refer to AV- 8 2 , "Ignition Signal Inspection" .
Vehicle speed signal. Refer to AV- 8 0 , "Vehicle Speed Signal Inspection" .
CAN communication line. Refer to AV- 8 5 , "CAN Communication Line Inspec-
tion" .
Display unit
A/C and AV switch and all switch operation are not
possible.
(Do not start self-diagnosis.)Refer to AV-84, "
A/C and AV Switch Does Not Operate" .
Air conditioner operation is not possible.
A/C and AV switch. Refer to AV-41, "A/C and AV Switch Inspection" .
CAN communication line. Refer to AV- 8 5 , "CAN Communication Line Inspec-
tion" .
Page 672 of 4449
INTEGRATED DISPLAY SYSTEM
AV-81
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
2. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect display unit connector and unified meter and A/C amp. connector.
3. Check continuity between display unit harness connector M62
terminal 7 (R/G) and unified meter and A/C amp. harness con-
nector M56 terminal 26 (R/G).
4. Check continuity between display unit harness connector M62
terminal 7 (R/G) and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK VEHICLE SPEED SIGNAL
1. Connect unified meter and A/C amp. connector.
2. Drive vehicle at a constant speed.
3. Check the signal between display unit harness connector M62
terminal 7 (R/G) and ground with CONSULT-II or oscilloscope.
OK or NG
OK >> Replace display unit.
NG >> Check unified meter and A/C amp. system, refer to DI-17, "
Vehicle Speed Signal Inspection" .
Illumination Signal InspectionAKS00BOM
1. CHECK ILLUMINATION SIGNAL
1. Check voltage between display unit and ground.
OK or NG
OK >> INSPECTON END
NG >> Repair harness or connector.7 – 26 : Continuity should exist.
7 – Ground : Continuity should not exist.
SKIA4989E
7 – Ground:
SKIA4991E
PKIA1935E
Terminals
Lighting switch position
(+)
(–)
ConnectorTerminal
(Wire color)ON OFF
M62 4 (R/L) Ground Approx. 12V Approx. 0V
SKIB0446E
Page 685 of 4449
AV-94
NAVIGATION SYSTEM
Revision: 2004 November 2004 FX35/FX45
Display with Pushed “SETTING” Button
The function of each icon is as follows:
Display Settings
How To Perform Display Setting
1. Start the engine.
2. Push “SETTING” button.
3. Select “Display”.
4. Push “Enter” switch.
Application Items
Brightness/Contrast/Map Back Ground
Select “Brightness/Contrast/Map Background”.
Brightness, Contrast and Back ground are shown at the lower part of the screen, and it can be set by
pushing joystick.
Display Off
Select “Display Off”.
When setting is turned on (Indicator light ON), the display will be under sleep mode.
Setting of the Under Section Display
Select “Setting of the under section display”.
The setting status that is selected from A/C or AV is shown at the lower part of the screen.
SKIA4496E
Icon Description
Display Settings of display can be performed.
Vehicle Electronic Systems Settings of vehicle electrical equipment can be performed.
System Settings Settings of linguistic select , time adjusting and beep sound can be performed.
Navigation Settings and adjusting of navigation can be performed.
Short Menus Easy Mode and Expert Easy Mode can be switched.
Guidance Volume The volume and/or on/off of voice prompt can be controlled by the joystick.
Help (only easy mode) Explanation of navigational functions appear on the display.
SKIA5791E
Icon Description Reference page
Brightness/Contrast/Map Background Brightness, Contrast and Map Background can be set.AV- 9 4
Display Off Display sleep mode ON/OFF can be switched.AV- 9 4
Setting of the under section display The setting status of A/C or AV can be shown. AV- 9 4