transmission INFINITI FX35 2005 Manual PDF

AT-290
DISASSEMBLY
Revision: 2005 July 2005 FX
DISASSEMBLYPFP:31020
DisassemblyACS0081L
CAUTION:
Do not disassemble parts behind Drum Support. Refer to AT- 1 8 , "
Cross-Sectional View (2WD Models)"
or AT- 1 9 , "Cross-Sectional View (AWD Models)" .
1. Drain ATF through drain plug.
2. Remove torque converter by holding it firmly and turing while pulling straight out.
3. Check torque converter one-way clutch using check tool as shown in the figure.
a. Insert check tool into the groove of bearing support built into one-way clutch outer race.
b. When fixing bearing support with check tool, rotate one-way clutch spline using screwdriver.
c. Make sure that inner race rotates clockwise only. If not, replace torque converter assembly.
4. Remove converter housing from transmission case. CAUTION:
Be careful not to scratch converter housing.
SCIA5010E
SCIA3171E
SCIA3427E

DISASSEMBLY AT-291
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
5. Remove O-ring from input clutch assembly.
6. Remove tightening bolts for oil pump assembly and transmis-
sion case.
7. Attach the sliding hammers to oil pump assembly and extract it evenly from transmission case.
CAUTION:

Fully tighten sliding hammer screw.

Make sure that bearing race is installed to the oil pump
assembly edge surface.
8. Remove O-ring from oil pump assembly.
SCIA5011E
SCIA2300E
SCIA5474E
SCIA5172E

DISASSEMBLY AT-293
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
14. Loosen lock nut and remove band servo anchor end pin from
transmission case.
15. Remove brake band from transmission case.

To prevent brake linings from cracking or peeling, do not
stretch the flexible band unnecessarily. When removing
the brake band, always secure it with a clip as shown in
the figure at right.
Leave the clip in position after removing the brake band.

Check brake band facing for damage, cracks, wear or
burns.
16. Remove mid carrier assembly and rear carrier assembly as a unit.
17. Remove mid carrier assembly from rear carrier assembly.
SCIA6512E
SCIA2580E
SAT655
SCIA5017E
SCIA5697E

DISASSEMBLY AT-297
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
33. Disconnect revolution sensor connector.
CAUTION:
Be careful not to damage connector.
34. Straighten terminal clips to free revolution sensor harness.
35. Remove bolts A, B and C from control valve with TCM.
36. Remove control valve with TCM from transmission case. CAUTION:
When removing, be careful with the manual valve notch and
manual plate height.Remove it vertically.
37. Remove A/T fluid temperature sensor 2 with bracket from con- trol valve with TCM.
SCIA5024E
SCIA5293E
Bolt symbol Length mm (in) Number of bolts
A 42 (1.65) 5
B 55 (2.17) 6
C 40 (1.57) 1
SCIA5025E
SCIA5260E
SCIA5301E

DISASSEMBLY AT-299
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
43. Remove rear extension assembly (2WD models) or adapter case assembly (AWD models) according to
the following procedures.
a. 2WD models
i. Remove tightening bolts for rear extension assembly and trans- mission case.
ii. Tap rear extension assembly with soft hammer.
iii. Remove rear extension assembly from transmission case. (With needle bearing.)
SCIA6941E
SCIA5028E
SCIA5029E

AT-300
DISASSEMBLY
Revision: 2005 July 2005 FX
b.AW D m o d e l s
i. Remove tightening bolts (1) for adapter case assembly and transmission case. [With bracket (2).]
: Bolt (10)

Self-sealing bolts (3)
ii. Tap adapter case assembly with soft hammer.
iii. Remove adapter case assembly from transmission case. (With needle bearing)
SCIA7210E
SCIA5201E
SCIA5186E

DISASSEMBLY AT-301
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
iv. Remove gasket from transmission case.
44. Remove bearing race from output shaft.
45. Remove output shaft from transmission case by rotating left/
right.
46. Remove parking gear from output shaft.
47. Remove seal rings from output shaft.
SCIA5231E
SCIA5245E
SCIA5030E
SCIA5247E
SCIA5209E

AT-302
DISASSEMBLY
Revision: 2005 July 2005 FX
48. Remove needle bearing from transmission case.
49. Remove revolution sensor from transmission case. CAUTION:

Do not subject it to impact by dropping or hitting it.

Do not disassemble.

Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.

Do not place in an area affected by magnetism.
50. Remove reverse brake snap ring (fixing plate) using 2 flat- bladed screwdrivers.
NOTE:
Press out snap ring from the transmission case oil pan side gap
using a flat-bladed screwdriver, and remove it using another
screwdriver.
51. Remove reverse brake retaining plate from transmission case.

Check facing for burns, cracks or damage. If necessary,
replace the plate.
52. Remove N-spring from transmission case.
53. Remove reverse brake drive plates, driven plates and dish plate from transmission case.

Check facing for burns, cracks or damage. If necessary,
replace the plate.
SCIA5031E
SCIA2320E
SCIA5032E
SCIA5214E
SCIA2322E

DISASSEMBLY AT-303
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
54. Remove snap ring (fixing spring retainer) using a flat-bladed
screwdriver.
55. Remove spring retainer and return spring from transmission case.
56. Remove seal rings from drum support.
57. Remove needle bearing from drum support edge surface.
SCIA2323E
SCIA2324E
SCIA3333E
SCIA2796E

AT-304
DISASSEMBLY
Revision: 2005 July 2005 FX
58. Remove reverse brake piston from transmission case with com-
pressed air. Refer to AT- 2 8 6 , "
Oil Channel" .
CAUTION:
Care should be taken not to abruptly blow air. It makes pis-
tons incline, as the result, it becomes hard to disassemble
the pistons.
59. Remove D-rings from reverse brake piston.
60. Use a pin punch (4mm dia. commercial service tool) to knock out retaining pin.
61. Remove manual shaft retaining pin with nippers.
SCIA5047E
SCIA5340E
SCIA2328E
SCIA2329E