revolution sensor INFINITI QX4 2001 Factory User Guide

Detected items
(Screen terms for CONSULT-II, ªSELF-DIAG
RESULTSº test mode)
Malfunction is detected when ...TCM self-diagnosis OBD-II (DTC)
Available by
O/D OFF
indicator lamp or
ªA/Tº on CONSULT-IIAvailable by
malfunction
indicator lamp*2,
ªENGINEº on CON-
SULT-II or GST ªA/Tº ªENGINEº
Overrun clutch solenoid valveITCM detects an improper volt-
age drop when it tries to operate
the solenoid valve.X P1760
OVERRUN CLUTCH
S/VO/R CLUCH SOL/
CIRC
T/C clutch solenoid valveITCM detects an improper volt-
age drop when it tries to operate
the solenoid valve.X P0740
T/C CLUTCH SOL/V TCC SOLENOID/
CIRC
Line pressure solenoid valveITCM detects an improper volt-
age drop when it tries to operate
the solenoid valve.X P0745
LINE PRESSURE
S/VL/PRESS SOL/CIRC
Throttle position sensor
Throttle position switchITCM receives an excessively
low or high voltage from the
sensor.X P1705
THROTTLE POSI
SENTP SEN/CIRC A/T
Engine speed signalITCM does not receive the
proper voltage signal from the
ECM.X P0725
ENGINE SPEED SIG
A/T fluid temperature sensorITCM receives an excessively
low or high voltage from the
sensor.X P0710
BATT/FLUID TEMP
SENATF TEMP SEN/
CIRC
Engine controlIThe ECM-AT communication
line is open or shorted.X EC-440, EC-603
A/T COMM LINE Ð
Turbine revolution sensorITCM does not receive the
proper voltage signal from the
sensor.XÐ
TURBINE REV
Ð
TCM (RAM)ITCM memory (RAM) is malfunc-
tioning.
ÐÐ
CONTROL UNIT
(RAM)Ð
TCM (ROM)ITCM memory (ROM) is malfunc-
tioning.
ÐÐ
CONTROL UNIT
(ROM)Ð
TCM (EEP ROM)ITCM memory (EEP ROM) is
malfunctioning.
ÐÐ
CONTROL UNIT
(EEP ROM)Ð
Initial startIThis is not a malfunction mes-
sage (Whenever shutting off a
power supply to the TCM, this
message appears on the
screen.)XÐ
INITIAL START
Ð
No failure
(NO DTC IS DETECTED FURTHER TEST-
ING MAY BE REQUIRED)INo failure has been detected.
XX
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
CONSULT-II (Cont'd)
AT-39

X: Applicable
Ð: Not applicable
*1: These malfunctions cannot be displayed by MIL
if another malfunction is assigned to MIL.
*2: Refer to EC-74, ªDESCRIPTIONº.
DATA MONITOR MODE (A/T)NBAT0184S03
Item DisplayMonitor item
Description Remarks
TCM input
signalsMain sig-
nals
Vehicle speed sensor 1
(A/T)
(Revolution sensor)VHCL/S SE´A/T
[km/h] or [mph]
XÐIVehicle speed computed
from signal of revolution
sensor is displayed.When racing engine in ªNº
or ªPº position with vehicle
stationary, CONSULT-II
data may not indicate 0
km/h (0 mph).
Vehicle speed sensor 2
(Meter)VHCL/S SE´MTR
[km/h] or [mph]
XÐIVehicle speed computed
from signal of vehicle
speed sensor is dis-
played.Vehicle speed display may
not be accurate under
approx. 10 km/h (6 mph). It
may not indicate 0 km/h (0
mph) when vehicle is sta-
tionary.
Throttle position sensor THRTL POS
SEN
[V]XÐIThrottle position sensor
signal voltage is dis-
played.
A/T fluid temperature sen-
sorFLUID TEMP SE
[V]
XÐIA/T fluid temperature
sensor signal voltage is
displayed.
ISignal voltage lowers as
fluid temperature rises.
Battery voltage BATTERY VOLT
[V]XÐISource voltage of TCM
is displayed.
Engine speed ENGINE SPEED
[rpm]
XXIEngine speed, computed
from engine speed
signal, is displayed.Engine speed display may
not be accurate under
approx. 800 rpm. It may
not indicate 0 rpm even
when engine is not run-
ning.
Turbine revolution sensor TURBINE REV
[rpm]
XÐITurbine revolution com-
puted from signal of tur-
bine revolution sensor is
displayed.Error may occur under
approx. 800 rpm and will
not indicate 0 rpm even if
engine is not running.
Overdrive control switch OVERDRIVE SW
[ON/OFF] X ÐION/OFF state computed
from signal of overdrive
control SW is displayed.
PN position switch PN POSI SW
[ON/OFF] X ÐION/OFF state computed
from signal of PN posi-
tion SW is displayed.
R position switch R POSITION SW
[ON/OFF] X ÐION/OFF state computed
from signal of R position
SW is displayed.
D position switch D POSITION SW
[ON/OFF] X ÐION/OFF state computed
from signal of D position
SW is displayed.
2 position switch 2 POSITION SW
[ON/OFF]
XÐION/OFF status, com-
puted from signal of 2
position SW, is dis-
played.
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
CONSULT-II (Cont'd)
AT-40

JUDGEMENT OF SELF-DIAGNOSIS CODENBAT0206S04
O/D OFF indicator lamp:
All judgement flickers are same.
SAT666I
All circuits that can be confirmed by self-diagnosis are OK.1st judgement flicker is longer than others.
SAT667I
Revolution sensor circuit is short-circuited or disconnected.
ÞGo to DTC P0720 VEHICLE SPEED SENSOR´A/T (REVO-
LUTION SENSOR), AT-111.
2nd judgement flicker is longer than others.
SAT668I
Vehicle speed sensor circuit is short-circuited or disconnected.
ÞGo to DTC VEHICLE SPEED SENSOR´MTR, AT-197.3rd judgement flicker is longer than others.
SAT669I
Throttle position sensor circuit is short-circuited or disconnected.
ÞGo to DTC P1705 THROTTLE POSITION SENSOR,
AT-176.
4th judgement flicker is longer than others.
SAT670I
Shift solenoid valve A circuit is short-circuited or disconnected.
ÞGo to DTC P0750 SHIFT SOLENOID VALVE A, AT-168.5th judgement flicker is longer than others.
SAT671I
Shift solenoid valve B circuit is short-circuited or disconnected.
ÞGo to DTC P0755 SHIFT SOLENOID VALVE B, AT-172.
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
Diagnostic Procedure Without CONSULT-II (Cont'd)
AT-50

O/D OFF indicator lamp:
6th judgement flicker is longer than others.
SAT672I
Overrun clutch solenoid valve circuit is short-circuited or discon-
nected.
ÞGo to DTC P1760 OVERRUN CLUTCH SOLENOID VALVE,
AT-185.7th judgement flicker is longer than others.
SAT673I
Torque converter clutch solenoid valve circuit is short-circuited
or disconnected.
ÞGo to DTC P0740 TORQUE CONVERTER CLUTCH SOLE-
NOID VALVE, AT-148.
8th judgement flicker is longer than others.
SAT674I
A/T fluid temperature sensor is disconnected or TCM power
source circuit is damaged.
ÞGo to DTC BATT/FLUID TEMP SEN (A/T FLUID TEM-
PERATURE SENSOR AND TCM POWER SOURCE), AT-190.9th judgement flicker is longer than others.
SAT675I
Engine speed signal circuit is short-circuited or disconnected.
ÞGo to DTC P0725 ENGINE SPEED SIGNAL, AT-116.
10th judgement flicker is longer than others.
SAT676I
Turbine revolution sensor circuit is short-circuited or discon-
nected.
ÞGo to DTC Turbine Revolution Sensor, AT-202.11th judgement flicker is longer than others.
SAT677I
Line pressure solenoid valve circuit is short-circuited or discon-
nected.
ÞGo to DTC P0745 LINE PRESSURE SOLENOID VALVE,
AT-162.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
Diagnostic Procedure Without CONSULT-II (Cont'd)
AT-51

Diagnostic Worksheet=NBAT0019S0102
1.lRead the Fail-safe Remarks and listen to customer complaints. AT-8
2.lCHECK A/T FLUIDAT-59
lLeakage (Follow specified procedure)
lFluid condition
lFluid level
3. Perform STALL TEST and LINE PRESSURE TEST. AT-59, AT-62
lStall test Ð Mark possible damaged components/others.
lTorque converter one-way clutch
lReverse clutch
lForward clutch
lOverrun clutch
lForward one-way clutchlLow & reverse brake
lLow one-way clutch
lEngine
lLine pressure is low
lClutches and brakes except high clutch and
brake band are OK
lPressure test Ð Suspected parts:
4.lPerform all ROAD TEST and mark required procedures. AT-63
4-1. Check before engine is started.AT-64
lSELF-DIAGNOSTIC PROCEDURE - Mark detected items.
lDTC P0705 PNP switch, AT-99.
lDTC P0710 A/T fluid temperature sensor, AT-105.
lDTC P0720 Vehicle speed sensor´A/T (Revolution sensor), AT-111.
lDTC P0725 Engine speed signal, AT-116.
lDTC P0740 Torque converter clutch solenoid valve, AT-148.
lDTC P0745 Line pressure solenoid valve, AT-162.
lDTC P0750 Shift solenoid valve A, AT-168.
lDTC P0755 Shift solenoid valve B, AT-172.
lDTC P1705 Throttle position sensor, AT-176.
lDTC P1760 Overrun clutch solenoid valve, AT-185.
lDTC BATT/FLUID TEMP SEN (A/T fluid temperature sensor and TCM power source), AT-190.
lDTC Vehicle speed sensor´MTR, AT-197.
lDTC Turbine revolution sensor, AT-202.
lDTC A/T communication line, AT-207.
lDTC Control unit (RAM), control unit (ROM), AT-211.
lDTC Control unit (EEP ROM), AT-213.
lPNP, overdrive control and throttle position switches, AT-257.
lBattery
lOthers
4-2. Check at idleAT-66
l1. O/D OFF Indicator Lamp Does Not Come On, AT-218.
l2. Engine Cannot Be Started In ªPº And ªNº Position, AT-221.
l3. In ªPº Position, Vehicle Moves Forward Or Backward When Pushed, AT-222.
l4. In ªNº Position, Vehicle Moves, AT-223.
l5. Large Shock. ªNº,ªRº Position, AT-225.
l6. Vehicle Does Not Creep Backward In ªRº Position, AT-227.
l7. Vehicle Does Not Creep Forward In ªDº, ª2º Or ª1º Position, AT-230.GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
TROUBLE DIAGNOSIS Ð INTRODUCTION
Introduction (Cont'd)
AT-55

4. 4-3. Cruise testAT-67
AT-71
Part-1
l8. Vehicle Cannot Be Started From D
1, AT-233.
l9. A/T Does Not Shift: D
1,D2Or Does Not Kickdown: D4,D2, AT-236.
l10. A/T Does Not Shift: D
2,D3, AT-239.
l11. A/T Does Not Shift: D
3,D4, AT-242.
l12. A/T Does Not Perform Lock-up, AT-245.
l13. A/T Does Not Hold Lock-up Condition, AT-247.
l14. Lock-up Is Not Released, AT-249.
l15. Engine Speed Does Not Return To Idle (Light Braking D
4,D3), AT-250.
Part-2AT-75
l16. Vehicle Does Not Start From D
1, AT-252.
l9. A/T Does Not Shift: D
1,D2Or Does Not Kickdown: D4,D2, AT-236.
l10. A/T Does Not Shift: D
2,D3, AT-239.
l11. A/T Does Not Shift: D
3,D4, AT-242.
Part-3AT-77
l17. A/T Does Not Shift: D
4,D3When Overdrive Control Switch ªONº,ªOFFº, AT-253
l15. Engine Speed Does Not Return To Idle (Engine Brake In D
3), AT-250.
l18. A/T Does Not Shift: D
3,22, When Selector Lever ªDº,ª2º Position, AT-254.
l15. Engine Speed Does Not Return To Idle (Engine Brake In 2
2), AT-250.
l19. A/T Does Not Shift: 2
2,11, When Selector Lever ª2º,ª1º Position, AT-255.
l20. Vehicle Does Not Decelerate By Engine Brake, AT-256.
lSELF-DIAGNOSTIC PROCEDURE Ð Mark detected items.
lDTC P0705 PNP switch, AT-99.
lDTC P0710 A/T fluid temperature sensor, AT-105.
lDTC P0720 Vehicle speed sensor´A/T (Revolution sensor), AT-111.
lDTC P0725 Engine speed signal, AT-116.
lDTC P0740 Torque converter clutch solenoid valve, AT-148.
lDTC P0745 Line pressure solenoid valve, AT-162.
lDTC P0750 Shift solenoid valve A, AT-168.
lDTC P0755 Shift solenoid valve B, AT-172.
lDTC P1705 Throttle position sensor, AT-176.
lDTC P1760 Overrun clutch solenoid valve, AT-185.
lDTC BATT/FLUID TEMP SEN (A/T fluid temperature sensor and TCM power source), AT-190.
lDTC Vehicle speed sensor´MTR, AT-197.
lDTC Turbine revolution sensor, AT-202.
lDTC A/T communication line, AT-207.
lDTC Control unit (RAM), control unit (ROM), AT-211.
lDTC Control unit (EEP ROM), AT-213.
lPNP, overdrive control and throttle position switches, AT-257.
lBattery
lOthers
5.lFor self-diagnosis NG items, inspect each component. Repair or replace the damaged parts. AT-38
6.lPerform all ROAD TEST and re-mark required procedures. AT-63
7.lPerform DTC CONFIRMATION PROCEDURE for following MIL indicating items and check out NG items.
Refer to EC-60, ªEmission-related Diagnostic Informationº.EC-60
lDTC (P0731, 1103) A/T 1st gear function, AT-120.
lDTC (P0732, 1104) A/T 2nd gear function, AT-126.
lDTC (P0733, 1105) A/T 3rd gear function, AT-132.
lDTC (P0734, 1106) A/T 4th gear function, AT-138.
lDTC (P0744, 1107) A/T TCC S/V function (lock-up), AT-153.
8.lPerform the Diagnostic Procedures for all remaining items marked NG. Repair or replace the damaged
parts.
Refer to the Symptom Chart when you perform the procedures. (The chart also shows some other possible
symptoms and the component inspection orders.)AT-92
AT-97
9.lErase DTC from TCM and ECM memories. AT-35
TROUBLE DIAGNOSIS Ð INTRODUCTION
Introduction (Cont'd)
AT-56

Symptom ChartNBAT0233Numbers are arranged in order of inspection.
Perform inspections starting with number one and work up.
Items Symptom Condition Diagnostic Item Reference Page
No Lock-up
Engagement/TCC
InoperativeTorque converter
is not locked up.ON vehicle1. Throttle position sensor (Adjustment) EC-174
2. Vehicle speed sensor´A/T (Revolution
sensor) and vehicle speed sensor´MTRAT- 111 , 1 9 7
3. Park/neutral position (PNP) switch
adjustmentAT-276
4. Engine speed signal AT-116
5. A/T fluid temperature sensor AT-105
6. Line pressure test AT-62
7. Torque converter clutch solenoid valve AT-148
8. Control valve assembly AT-273
OFF vehicle 9. Torque converter AT-286
Torque converter
clutch piston slip.ON vehicle1. Fluid level AT-59
2. Throttle position sensor (Adjustment) EC-174
3. Line pressure test AT-62
4. Torque converter clutch solenoid valve AT-148
5. Line pressure solenoid valve AT-162
6. Control valve assembly AT-273
OFF vehicle 7. Torque converter AT-286
Lock-up point is
extremely high or
low.
AT-245ON vehicle1. Throttle position sensor (Adjustment) EC-174
2. Vehicle speed sensor´A/T (Revolution
sensor) and vehicle speed sensor´MTRAT- 111 , 1 9 7
3. Torque converter clutch solenoid valve AT-148
4. Control valve assembly AT-273
Shift ShockSharp shock in
shifting from N to
D position.ON vehicle1. Engine idling rpm EC-431
2. Throttle position sensor (Adjustment) EC-174
3. Line pressure test AT-62
4. A/T fluid temperature sensor AT-105
5. Engine speed signal AT-116
6. Line pressure solenoid valve AT-162
7. Control valve assembly AT-273
8. Accumulator N-D AT-273
OFF vehicle9. Turbine revolution sensor EC-368
10. Forward clutch AT-320
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
TROUBLE DIAGNOSIS Ð GENERAL DESCRIPTION
Symptom Chart
AT-81

Items Symptom Condition Diagnostic Item Reference Page
Shift ShockToo sharp a
shock in change
from D
1to D2.ON vehicle1. Throttle position sensor (Adjustment) EC-174
2. Line pressure test AT-62
3. Accumulator servo release AT-273
4. Control valve assembly AT-273
5. A/T fluid temperature sensor AT-105
OFF vehicle 6. Brake band AT-333
Too sharp a
shock in change
from D
2to D3.ON vehicle1. Throttle position sensor (Adjustment) EC-174
2. Line pressure test AT-62
3. Control valve assembly AT-273
OFF vehicle4. High clutch AT-317
5. Brake band AT-333
Too sharp a
shock in change
from D
3to D4.ON vehicle1. Throttle position sensor (Adjustment) EC-174
2. Line pressure test AT-62
3. Control valve assembly AT-273
OFF vehicle4. Brake band AT-333
5. Overrun clutch AT-320
Gear change
shock felt during
deceleration by
releasing accel-
erator pedal.ON vehicle1. Throttle position sensor (Adjustment) EC-174
2. Line pressure test AT-62
3. Overrun clutch solenoid valve AT-185
4. Control valve assembly AT-273
Large shock
changing from 1
2to 11in 1 position.ON vehicle 1. Control valve assembly AT-273
ON vehicle 2. Low & reverse brake AT-324
Improper Shift
TimingToo high a gear
change point from
D
1to D2, from D2to D3, from D3to
D
4.
AT-236, 239, 242ON vehicle1. Throttle position sensor (Adjustment) EC-174
2. Vehicle speed sensor´A/T (Revolution
sensor) and vehicle speed sensor´MTRAT- 111 , 1 9 7
3. Shift solenoid valve A AT-168
4. Shift solenoid valve B AT-172
Gear change
directly from D
1to
D
3occurs.ON vehicle1. Fluid level AT-59
2. Accumulator servo release AT-273
OFF vehicle 3. Brake band AT-333
Too high a
change point from
D
4to D3, from D3to D2, from D2to
D
1.ON vehicle1. Throttle position sensor (Adjustment) EC-174
2. Vehicle speed sensor´A/T (Revolution
sensor) and vehicle speed sensor´MTRAT- 111 , 1 9 7
Kickdown does
not operate when
depressing pedal
in D
4within kick-
down vehicle
speed.ON vehicle1. Throttle position sensor (Adjustment) EC-174
2. Vehicle speed sensor´A/T (Revolution
sensor) and vehicle speed sensor´MTRAT- 111 , 1 9 7
3. Shift solenoid valve A AT-168
4. Shift solenoid valve B AT-172
TROUBLE DIAGNOSIS Ð GENERAL DESCRIPTION
Symptom Chart (Cont'd)
AT-82

Items Symptom Condition Diagnostic Item Reference Page
Improper Shift
TimingKickdown oper-
ates or engine
overruns when
depressing pedal
in D
4beyond kick-
down vehicle
speed limit.ON vehicle1. Vehicle speed sensor´A/T (Revolution
sensor) and vehicle speed sensor´MTRAT- 111 , 1 9 7
2. Throttle position sensor (Adjustment) EC-174
3. Shift solenoid valve A AT-168
4. Shift solenoid valve B AT-172
Gear change from
2
2to 23in 2 posi-
tion.ON vehicle1. Park/neutral position (PNP) switch
adjustmentAT-276
Gear change from
1
1to 12in 1 posi-
tion.ON vehicle1. Park/neutral position (PNP) switch
adjustmentAT-276
2. Manual control linkage adjustment AT-276
No Down ShiftFailure to change
gear from D
4to
D
3.ON vehicle1. Fluid level AT-59
2. Throttle position sensor (Adjustment) EC-174
3. Overrun clutch solenoid valve AT-185
4. Shift solenoid valve A AT-168
5. Line pressure solenoid valve AT-162
6. Control valve assembly AT-273
OFF vehicle7. Low & reverse brake AT-324
8. Overrun clutch AT-320
Failure to change
gear from D
3to
D
2or from D4to
D
2.ON vehicle1. Fluid level AT-59
2. Throttle position sensor (Adjustment) EC-174
3. Shift solenoid valve A AT-168
4. Shift solenoid valve B AT-172
5. Control valve assembly AT-273
OFF vehicle6. High clutch AT-317
7. Brake band AT-333
Failure to change
gear from D
2to
D
1or from D3to
D
1.ON vehicle1. Fluid level AT-59
2. Throttle position sensor (Adjustment) EC-174
3. Shift solenoid valve A AT-168
4. Shift solenoid valve B AT-172
5. Control valve assembly AT-273
OFF vehicle6. Low one-way clutch AT-328
7. High clutch AT-317
8. Brake band AT-333
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
TROUBLE DIAGNOSIS Ð GENERAL DESCRIPTION
Symptom Chart (Cont'd)
AT-83

Items Symptom Condition Diagnostic Item Reference Page
No Down ShiftFailure to change
from D
3to 22when changing
lever into 2 posi-
tion.
AT-250ON vehicle1. Park/neutral position (PNP) switch
adjustmentAT-276
2. Throttle position sensor (Adjustment) EC-174
3. Overrun clutch solenoid valve AT-185
4. Shift solenoid valve B AT-172
5. Shift solenoid valve A AT-168
6. Control valve assembly AT-273
7. Manual control linkage adjustment AT-276
OFF vehicle8. Brake band AT-333
9. Overrun clutch AT-320
Does not change
from 1
2to 11in 1
position.ON vehicle1. Park/neutral position (PNP) switch
adjustmentAT-276
2. Vehicle speed sensor´A/T (Revolution
sensor) and vehicle speed sensor´MTRAT- 111 , 1 9 7
3. Shift solenoid valve A AT-168
4. Control valve assembly AT-273
5. Overrun clutch solenoid valve AT-185
OFF vehicle6. Overrun clutch AT-320
7. Low & reverse brake AT-324
No Up ShiftFailure to change
gear from D
1to
D
2.ON vehicle1. Park/neutral position (PNP) switch
adjustmentAT-276
2. Manual control linkage adjustment AT-276
3. Shift solenoid valve A AT-168
4. Control valve assembly AT-273
5. Vehicle speed sensor´A/T (Revolution
sensor) and vehicle speed sensor´MTRAT- 111 , 1 9 7
OFF vehicle 6. Brake band AT-333
Failure to change
gear from D
2to
D
3.ON vehicle1. Park/neutral position (PNP) switch
adjustmentAT-276
2. Manual control linkage adjustment AT-276
3. Shift solenoid valve B AT-172
4. Control valve assembly AT-273
5. Vehicle speed sensor´A/T (Revolution
sensor) and vehicle speed sensor´MTRAT- 111 , 1 9 7
OFF vehicle6. High clutch AT-317
7. Brake band AT-333
TROUBLE DIAGNOSIS Ð GENERAL DESCRIPTION
Symptom Chart (Cont'd)
AT-84