clutch INFINITI QX56 2004 Factory Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2004, Model line: QX56, Model: INFINITI QX56 2004Pages: 3371, PDF Size: 78.5 MB
Page 378 of 3371
REPAIR FOR COMPONENT PARTS
AT-307
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
Direct ClutchUCS002J P
COMPONENTS
DISASSEMBLY
1. Using a flat-bladed screwdriver, remove snap rings from direct
clutch drum.
2. Remove drive plates, driven plates and retaining plate from
direct clutch drum.
INSPECTION
Check the following, and replace direct clutch assembly if necessary.
Direct Clutch Snap Rings
Check for deformation, fatigue or damage.
Direct Clutch Drive Plates
Check facing for burns, cracks or damage.
Direct Clutch Retaining Plate and Driven Plates
Check facing for burns, cracks or damage.
1. Direct clutch drum 2. Driven plate 3. Retaining plate
4. Snap ring 5. Drive plate
SCIA5242E
SCIA2868E
Page 379 of 3371
AT-308
REPAIR FOR COMPONENT PARTS
Revision: August 20072004 QX56
ASSEMBLY
1. Install drive plates, driven plates and retaining plate in direct
clutch drum.
CAUTION:
Take care with the order of plates.
2. Using a flat-bladed screwdriver, install snap rings in direct clutch
drum.
SCIA5243E
SCIA2868E
Page 389 of 3371
AT-318
ASSEMBLY
Revision: August 20072004 QX56
36. Install direct clutch assembly in reverse brake.
37. Install high and low reverse clutch assembly in direct clutch
assembly.
38. Using a flat-bladed screwdriver, range the drive plate.
39. Install high and low reverse clutch hub, mid sun gear assembly
and rear sun gear assembly as a unit.
SCIA5019E
SCIA2306E
SCIA3169E
SCIA5018E
Page 390 of 3371
ASSEMBLY
AT-319
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
CAUTION:
Check that portion A of high and low reverse clutch drum
protrudes approximately 2 mm (0.08 in) beyond portion B of
rear sun gear.
40. Install needle bearing in rear carrier assembly.
CAUTION:
Apply petroleum jelly to needle bearing.
41. Install bearing race in rear carrier assembly.
CAUTION:
Apply petroleum jelly to bearing race.
42. Install rear carrier assembly in direct clutch drum.
SCIA3130E
SCIA5179E
SCIA5178E
SCIA2462E
Page 391 of 3371
AT-320
ASSEMBLY
Revision: August 20072004 QX56
43. Install needle bearing (rear side) in mid carrier assembly.
CAUTION:
Apply petroleum jelly to needle bearing.
44. Install needle bearing (front side) in mid carrier assembly.
CAUTION:
Apply petroleum jelly to needle bearing.
45. Install mid carrier assembly in rear carrier assembly.
46. Install front carrier assembly, input clutch assembly and rear
internal gear as a unit.
47. Install seal rings in input clutch assembly.
CAUTION:
Do not reuse seal rings.
Apply petroleum jelly to seal rings.
SCIA5177E
SCIA5176E
SCIA5344E
SCIA5173E
SCIA5269E
Page 392 of 3371
ASSEMBLY
AT-321
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
48. Install band servo anchor end pin and lock nut in transmission
case.
CAUTION:
Do not reuse band servo anchor end pin.
49. Install brake band in transmission case.
CAUTION:
Assemble it so that identification to avoid incorrect installa-
tion faces servo side.
50. Install front sun gear assembly to front carrier assembly.
CAUTION:
Apply ATF to front sun gear radial bearing and 3rd one-way
clutch end bearing.
51. Install needle bearing in front sun gear assembly.
CAUTION:
Apply petroleum jelly to needle bearing.
52. Adjust brake band tilting using clips so that brake band contacts
front sun gear drum evenly.
SCIA5016E
SCIA2809E
SCIA5014E
SCIA2808E
SCIA5033E
Page 396 of 3371
ASSEMBLY
AT-325
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
3. Install oil pump assembly in transmission case.
CAUTION:
Apply ATF to oil pump radial bearing.
4. Apply recommended sealant (Genuine RTV Silicone Sealant or
equivalent. Refer to GI-45, "
Recommended Chemical Products
and Sealants" .) to oil pump assembly as shown in illustration.
CAUTION:
Complete remove all moisture, oil and old sealant, etc.
From the oil pump mounting bolts and oil pump mounting
bolt mounting surfaces.
5. Tighten oil pump mounting bolts to specified torque. Refer to AT-
261, "Components" .
CAUTION:
Apply ATF to oil pump bushing.
6. Install O-ring to input clutch assembly.
CAUTION:
Do not reuse O-ring.
Apply ATF to O-ring.
7. Install converter housing to transmission case.
CAUTION:
Do not reuse self-sealing bolt.
SCIA2 811 E
SCIA5321E
SCIA2300E
SCIA5 011 E
Converter housing mounting bolt:
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt:
: 61 N·m (6.2 kg-m, 45 ft-lb)
SCIA5171E
Page 406 of 3371
ATC-1
AUTOMATIC AIR CONDITIONER
J AIR CONDITIONER
CONTENTS
C
D
E
F
G
H
I
K
L
M
SECTION AT C
A
B
AT C
Revision: August 20072004 QX56 PRECAUTIONS .......................................................... 5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 5
Precautions for Working with HFC-134a (R-134a) ..... 5
Contaminated Refrigerant ........................................ 5
General Refrigerant Precautions .............................. 6
Precautions for Leak Detection Dye ......................... 6
A/C Identification Label ............................................ 7
Precautions for Refrigerant Connection ................... 7
FEATURES OF NEW TYPE REFRIGERANT
CONNECTION ...................................................... 7
O-RING AND REFRIGERANT CONNECTION ..... 8
Precautions for Servicing Compressor ....................11
Precautions for Service Equipment .........................11
RECOVERY/RECYCLING EQUIPMENT .............11
ELECTRONIC LEAK DETECTOR .......................11
VACUUM PUMP ................................................. 12
MANIFOLD GAUGE SET .................................... 12
SERVICE HOSES ............................................... 12
SERVICE COUPLERS ........................................ 13
REFRIGERANT WEIGHT SCALE ...................... 13
CHARGING CYLINDER ...................................... 13
Wiring Diagrams and Trouble Diagnosis ................ 13
PREPARATION ......................................................... 14
Special Service Tools ............................................. 14
HFC-134a (R-134a) Service Tools and Equipment ... 14
Commercial Service Tools ...................................... 17
REFRIGERATION SYSTEM ..................................... 18
Refrigerant Cycle ................................................... 18
REFRIGERANT FLOW ....................................... 18
Refrigerant System Protection ............................... 18
REFRIGERANT PRESSURE SENSOR ............. 18
PRESSURE RELIEF VALVE .............................. 19
Component Layout ................................................. 20
FRONT REFRIGERATION SYSTEM .................. 20
REAR REFRIGERATION SYSTEM .................... 21LUBRICANT .............................................................. 22
Maintenance of Lubricant Quantity in Compressor ... 22
LUBRICANT ........................................................ 22
CHECKING AND ADJUSTING ............................ 22
AIR CONDITIONER CONTROL ............................... 24
Description .............................................................. 24
Operation ................................................................ 24
AIR MIX DOORS CONTROL .............................. 24
FAN SPEED CONTROL ...................................... 24
INTAKE DOOR CONTROL ................................. 24
MODE DOOR CONTROL ................................... 24
DEFROSTER DOOR CONTROL ........................ 24
MAGNET CLUTCH CONTROL ........................... 25
SELF-DIAGNOSTIC SYSTEM ............................ 25
Description of Control System ................................ 26
Control Operation ................................................... 26
DISPLAY SCREEN .............................................. 27
AUTO SWITCH ................................................... 27
TEMPERATURE DIAL (DRIVER) ........................ 27
TEMPERATURE DIAL (PASSENGER) ............... 27
RECIRCULATION SWITCH () ............................. 27
DEFROSTER () SWITCH .................................... 27
REAR WINDOW DEFOGGER SWITCH ............. 27
OFF SWITCH (HOLD FAN DOWN SWITCH
UNTIL SYSTEM SHUTS OFF) ............................ 27
A/C SWITCH ....................................................... 27
MODE SWITCH .................................................. 27
FRONT FAN SWITCH ......................................... 27
REAR FAN SWITCH (FRONT) ............................ 27
REAR TEMPERATURE/MODE DIAL (FRONT) ... 27
REAR TEMPERATURE/MODE DIAL (REAR) .... 28
REAR FAN CONTROL SWITCH (REAR) ........... 28
Discharge Air Flow ................................................. 29
FRONT ................................................................ 29
REAR .................................................................. 29
System Description (Front) ..................................... 30
CONTROLS AND THEIR FUNCTIONS .............. 30
System Description (Rear) ..................................... 31
CONTROLS AND THEIR FUNCTIONS .............. 31
CAN Communication System Description .............. 32
Page 407 of 3371
ATC-2Revision: August 20072004 QX56 TROUBLE DIAGNOSIS ............................................ 33
CONSULT-II Function (BCM) .................................. 33
CONSULT-II BASIC OPERATION ....................... 33
DATA MONITOR .................................................. 34
How to Perform Trouble Diagnosis for Quick and
Accurate Repair ...................................................... 35
WORK FLOW ...................................................... 35
SYMPTOM TABLE .............................................. 35
Component Parts and Harness Connector Location ... 37
ENGINE COMPARTMENT .................................. 37
FRONT PASSENGER COMPARTMENT ............ 38
REAR PASSENGER COMPARTMENT ............... 39
Schematic ............................................................... 40
Wiring Diagram — A/C,A — ................................... 41
Front Air Control Terminals and Reference Value ... 51
PIN CONNECTOR TERMINAL LAYOUT ............ 51
TERMINALS AND REFERENCE VALUE FOR
FRONT AIR CONTROL ....................................... 51
A/C System Self-diagnosis Function ...................... 53
DESCRIPTION .................................................... 53
Operational Check (Front) ...................................... 56
CHECKING MEMORY FUNCTION ..................... 56
CHECKING BLOWER ......................................... 56
CHECKING DISCHARGE AIR ............................ 57
CHECKING RECIRCULATION ............................ 57
CHECKING TEMPERATURE DECREASE ......... 57
CHECKING TEMPERATURE INCREASE .......... 58
CHECK A/C SWITCH .......................................... 58
CHECKING AUTO MODE ................................... 58
Operational Check (Rear) ....................................... 59
CHECKING BLOWER ......................................... 59
CHECKING TEMPERATURE DECREASE ......... 59
CHECKING TEMPERATURE INCREASE .......... 59
Power Supply and Ground Circuit for Front Air Con-
trol ........................................................................... 60
INSPECTION FLOW ........................................... 60
COMPONENT DESCRIPTION ............................ 61
DIAGNOSTIC PROCEDURE FOR A/C SYSTEM ... 61
Mode Door Motor Circuit ........................................ 63
INSPECTION FLOW ........................................... 63
SYSTEM DESCRIPTION .................................... 64
COMPONENT DESCRIPTION ............................ 65
DIAGNOSTIC PROCEDURE FOR MODE
DOOR MOTOR ................................................... 65
Air Mix Door Motor Circuit ...................................... 67
INSPECTION FLOW ........................................... 67
SYSTEM DESCRIPTION .................................... 68
COMPONENT DESCRIPTION ............................ 69
DIAGNOSTIC PROCEDURE FOR AIR MIX
DOOR MOTOR (DRIVER) ................................... 69
DIAGNOSTIC PROCEDURE FOR AIR MIX
DOOR MOTOR (PASSENGER) .......................... 71
DIAGNOSTIC PROCEDURE FOR AIR MIX
DOOR MOTOR (REAR) ...................................... 73
Intake Door Motor Circuit ........................................ 76
INSPECTION FLOW ........................................... 76
SYSTEM DESCRIPTION .................................... 77
COMPONENT DESCRIPTION ............................ 78
DIAGNOSTIC PROCEDURE FOR INTAKE DOOR MOTOR ....................................................78
Defroster Door Motor Circuit ...................................79
SYMPTOM: ..........................................................79
INSPECTION FLOW ............................................79
SYSTEM DESCRIPTION .....................................80
COMPONENT DESCRIPTION ............................80
DIAGNOSTIC PROCEDURE FOR
DEFROSTER DOOR MOTOR .............................81
Front Blower Motor Circuit ......................................83
INSPECTION FLOW ............................................83
SYSTEM DESCRIPTION .....................................84
COMPONENT DESCRIPTION ............................85
DIAGNOSTIC PROCEDURE FOR BLOWER
MOTOR ................................................................85
COMPONENT INSPECTION ...............................89
Rear Blower Motor Circuit .......................................90
INSPECTION FLOW ............................................90
SYSTEM DESCRIPTION .....................................91
DIAGNOSTIC PROCEDURE FOR REAR
BLOWER MOTOR ...............................................91
COMPONENT INSPECTION ...............................99
Rear Air Control Circuit ......................................... 101
INSPECTION FLOW .......................................... 101
SYSTEM DESCRIPTION ................................... 102
DIAGNOSTIC PROCEDURE FOR REAR AIR
CONTROL ......................................................... 102
Magnet Clutch Circuit ............................................ 104
INSPECTION FLOW .......................................... 104
SYSTEM DESCRIPTION ................................... 105
DIAGNOSTIC PROCEDURE FOR MAGNET
CLUTCH ............................................................ 105
Insufficient Cooling ................................................110
INSPECTION FLOW ..........................................110
PERFORMANCE TEST DIAGNOSES .............. 111
PERFORMANCE CHART ..................................113
TROUBLE DIAGNOSES FOR UNUSUAL PRES-
SURE .................................................................114
Insufficient Heating ...............................................117
INSPECTION FLOW ..........................................117
Noise .....................................................................118
INSPECTION FLOW ..........................................118
Self-diagnosis ....................................................... 120
INSPECTION FLOW .......................................... 120
Memory Function .................................................. 121
INSPECTION FLOW .......................................... 121
Water Valve Circuit ................................................ 121
COMPONENT DESCRIPTION .......................... 121
DIAGNOSTIC PROCEDURE FOR WATER
VALVE ................................................................ 122
COMPONENT INSPECTION ............................. 124
Ambient Sensor Circuit ......................................... 125
COMPONENT DESCRIPTION .......................... 125
AMBIENT TEMPERATURE INPUT PROCESS . 125
DIAGNOSTIC PROCEDURE FOR AMBIENT
SENSOR ............................................................ 125
COMPONENT INSPECTION ............................. 127
In-vehicle Sensor Circuit ....................................... 128
COMPONENT DESCRIPTION .......................... 128
DIAGNOSTIC PROCEDURE FOR IN-VEHICLE
Page 408 of 3371
ATC-3
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: August 20072004 QX56 SENSOR ........................................................... 129
COMPONENT INSPECTION ............................ 131
Optical Sensor Circuit .......................................... 131
COMPONENT DESCRIPTION ......................... 131
OPTICAL INPUT PROCESS ............................ 131
DIAGNOSTIC PROCEDURE FOR OPTICAL
SENSOR ........................................................... 132
Intake Sensor Circuit ............................................ 133
COMPONENT DESCRIPTION ......................... 133
DIAGNOSTIC PROCEDURE FOR INTAKE SEN-
SOR .................................................................. 133
COMPONENT INSPECTION ............................ 134
CONTROL UNIT ..................................................... 135
Removal and Installation ...................................... 135
FRONT AIR CONTROL .................................... 135
REAR AIR CONTROL ....................................... 135
AMBIENT SENSOR ................................................ 136
Removal and Installation ...................................... 136
REMOVAL ......................................................... 136
INSTALLATION ................................................. 136
IN-VEHICLE SENSOR ............................................ 137
Removal and Installation ...................................... 137
REMOVAL ......................................................... 137
INSTALLATION ................................................. 137
OPTICAL SENSOR ................................................ 138
Removal and Installation ...................................... 138
INTAKE SENSOR ................................................... 139
Removal and Installation ...................................... 139
REMOVAL ......................................................... 139
INSTALLATION ................................................. 139
BLOWER MOTOR .................................................. 140
Components ......................................................... 140
Removal and Installation ...................................... 140
FRONT BLOWER MOTOR ............................... 140
REAR BLOWER MOTOR ................................. 141
IN-CABIN MICROFILTER ....................................... 142
Removal and Installation ...................................... 142
FUNCTION ........................................................ 142
REPLACEMENT TIMING .................................. 142
REPLACEMENT PROCEDURE ....................... 142
HEATER & COOLING UNIT ASSEMBLY .............. 144
Components ......................................................... 144
Removal and Installation ...................................... 145
FRONT HEATER AND COOLING UNIT ASSEM-
BLY .................................................................... 145
REAR HEATER AND COOLING UNIT ASSEM-
BLY .................................................................... 146
HEATER CORE ...................................................... 147
Components ......................................................... 147
Removal and Installation ...................................... 148
FRONT HEATER CORE ................................... 148
REAR HEATER CORE ..................................... 149
DEFROSTER DOOR MOTOR ................................ 150
Removal and Installation ...................................... 150
REMOVAL ......................................................... 150
INSTALLATION ................................................. 150INTAKE DOOR MOTOR .........................................151
Removal and Installation ......................................151
REMOVAL .........................................................151
INSTALLATION .................................................151
MODE DOOR MOTOR ............................................152
Removal and Installation ......................................152
REMOVAL .........................................................152
INSTALLATION .................................................152
AIR MIX DOOR MOTOR .........................................153
Components .........................................................153
Removal and Installation ......................................153
FRONT AIR MIX DOOR MOTOR (DRIVER) .....153
FRONT AIR MIX DOOR MOTOR (PASSENGER) .154
REAR AIR MIX DOOR MOTOR ........................154
VARIABLE BLOWER CONTROL ...........................155
Removal and Installation ......................................155
REMOVAL .........................................................155
INSTALLATION .................................................155
REAR BLOWER MOTOR RESISTOR ....................156
Removal and Installation ......................................156
REMOVAL .........................................................156
INSTALLATION .................................................156
DUCTS AND GRILLES ...........................................157
Components .........................................................157
Removal and Installation ......................................160
CENTER CONSOLE HEAT DUCT AND REAR
FINISHER ASSEMBLY GRILLE ........................160
DEFROSTER NOZZLE .....................................160
RH AND LH SIDE DEMISTER DUCT ...............160
RH AND LH VENTILATOR DUCT .....................160
CENTER VENTILATOR DUCT .........................160
FLOOR DUCT ...................................................160
REAR OVERHEAD DUCTS ..............................160
REAR FLOOR DUCT ........................................161
GRILLES ...........................................................161
REFRIGERANT LINES ...........................................162
HFC-134a (R-134a) Service Procedure ...............162
SETTING OF SERVICE TOOLS AND EQUIP-
MENT ................................................................162
Components .........................................................164
Removal and Installation for Compressor ............166
REMOVAL .........................................................166
INSTALLATION .................................................167
Removal and Installation for Compressor Clutch . 167
REMOVAL .........................................................167
INSPECTION ....................................................168
INSTALLATION .................................................168
BREAK-IN OPERATION ....................................170
Removal and Installation for Low-pressure Flexible
Hose .....................................................................170
REMOVAL .........................................................170
INSTALLATION .................................................170
Removal and Installation for High-pressure Flexible
Hose .....................................................................170
REMOVAL .........................................................170
INSTALLATION .................................................170
Removal and Installation for High-pressure Pipe . 170
REMOVAL .........................................................170
INSTALLATION .................................................171