turn signal INFINITI QX56 2007 Factory Owners Manual

NAVIGATION SYSTEM
AV-91
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
AV
N
O
P
Terminal and Reference Value for Display Control unitINFOID:0000000003533714
Te r m i n a l N o .
(Wire color)
ItemSignal
input/
outputCondition
Vo l ta g e
(Approx.)Example of
symptom
+–Igni-
tion
switchOperation
1 (Y) GroundBattery Pow-
erInput OFF – Battery voltageSystem does not
work properly.
2 (L/W) GroundPower Supply
(Inverter) Output ON – 9 VScreen is not
shown.
3 (B) Ground Ground – ON – 0 V –
4 (L/R) GroundPower Supply
(Signal) Output ON – 9 VScreen is not
shown.
5 (P) Ground(Inverter)
Ground –ON – 0 V –
6 (GR) GroundReverse
signalInput ONSelector lever in R
positionBattery voltage
Impossible to
gain direction of
vehicle. Selector lever not in
R position0 V
7 (P/L) Ground(Signal)
Ground –ON – 0 V –
10 (O) Ground ACC signal Input ACC – Battery voltageSystem does not
work properly.
12 (G/R) Ground Ignition signal Input ON – Battery voltageVehicle informa-
tion setting is not
possible.
13 (B) Ground Ground – ON – 0 V –
14 (R/L) GroundIllumination
signalInput OFFLighting switch posi-
tion 1st or 2ndBattery voltageDisplay unit
does not change
when lighting
switch is turned
to 1st position. Lighting switch posi-
tion OFF0 V
16 (W/R) GroundVehicle
speed signal
(8–pulse)Input ONWhen vehicle speed
is approx. 40 km/h
(25 MPH)Value of vehicle
speed informa-
tion is not accu-
rately displayed.
25 (L) – CAN-H – – – – –
26 (P) – CAN-L – – – – –
28 (V) GroundCommunica-
tion signal (+)Input/
OutputON –System does not
work properly.
29 – Shield ground – – – – –
SKIA0168E
SKIA0175E

AV-96
< SERVICE INFORMATION >
NAVIGATION SYSTEM
Terminal and Reference Value for AV Switch
INFOID:0000000003533716
18 (B) 7RGB signal
(B: blue)Input ONSelect “Display Di-
agnosis (DCU)” of
CONFIRMATION/
ADJUSTMENT
function.Screen looks
yellowish.
19 (G) 21RGB syn-
chronizing
signalInput ONPress the “TRIP”
button.NAVI screen is
rolling.
20 (W) 21Vertical syn-
chronizing
(VP) signalOutput ON –Operating
screen for audio
and A/C is not
displayed when
showing NAVI
screen.
21 – Shield ground – – – – –
22 (L) 23Display com-
munication
signal
(DSP-DCU)Output ON –Though a screen
is displayed, it is
impossible to ad-
just brightness.
23 – Shield ground – – – – – Terminal No. (Wire
color)
ItemSignal
input/
outputCondition
Voltag e
(Approx.)Example of
symptom
+–Igni-
tion
switchOperation
SKIA4982E
SKIA0164E
SKIA4983E
SKIA4363E
Te r m i n a l N o .
(Wire color)
ItemSignal
input/
outputCondition
Vo l ta g e
(Approx.)Example of
symptom
+–Ignition
switchOperation
1 (Y) Ground Battery power Input OFF - Battery voltageSystem does not
work properly.
2 (V) Ground ACC signal Input ACC - Battery voltageSystem does not
work properly.
3 (R/L) GroundIllumination
signalInput OFFLighting switch is
ON (position 1).Battery voltageAV switch illumi-
nation does not
come on when
lighting switch is
ON (position 1). Turn lighting switch
OFF.3.0V or less

AV-98
< SERVICE INFORMATION >
NAVIGATION SYSTEM
DIAGNOSIS ITEM
NOTE:
Make the status that is set by D/N function be shown.
Self-Diagnosis Mode (DCU)INFOID:0000000003533719
OPERATION PROCEDURE
1. Start the engine.
2. Turn the audio system off.
Mode Description
Self-diagnosis (DCU) Display control unit diagnosis.
Self-diagnosis (NAVI)• NAVI Control unit diagnosis (DVD-ROM drive) will not be diagnosed
when no map DVD-ROM is in it.
• Analyzes connection between the NAVI control unit and the GPS anten-
na and operation of each unit.
CONFIRMATION/
ADJUSTMENTDisplay diagnosisIn display control unit mode, color tone and shading of the screen can be
checked by the display of a color bar and a gray scale.
Vehicle signalsIn display control unit mode, analyzes the following vehicle signals: Vehicle
speed signal, light signal
NOTE, ignition switch signal, and reverse signal.
Auto Climate Control A/C self-diagnosis of A/C system.
NavigationDisplay diagnosisIn NAVI C/U mode, color tone and shading of the screen can be checked
by the display of a color bar and a gray scale.
Vehicle signalsIn NAVI C/U mode, analyzes the following vehicle signals: Vehicle speed
signal, light signal, ignition switch signal, and reverse signal.
History of ErrorsDiagnosis results previously stored in the memory (before turning ignition
switch ON) are displayed in this mode. Time and location when/where the
errors occurred are also displayed.
Naviga-
tionDisplay Lon-
gitude & Lat-
itudeDisplay the map. Use the joystick to adjust position. Longitude and latitude
will be displayed.
Speed Cali-
brationUnder ordinary conditions, the navigation system distance measuring func-
tion will automatically compensate for minute decreases in wheel and tire
diameter caused by tire wear or low-pressure. Speed calibration immedi-
ately restores system accuracy in cases such as when distance calibration
is needed because of the use of tire chains in inclement weather.
Angle ad-
justmentCorrects difference between actual turning angle of a vehicle and turning
angle of the car mark on the display.
Initialize Lo-
cationThis mode is for initializing the current location. Use when the vehicle is
transported a long distance on a trailer, etc.
CAN DIAG SUPPORT MONITOR Display status of CAN communication.

AV-106
< SERVICE INFORMATION >
NAVIGATION SYSTEM
• A comparison check can be made of each actual vehicle signal
and the signals recognized by the system.
CAUTION:
In case of confirming light signal, set D/N mode to ON/OFF of
light switch (normal setting).
• OFF: D (Day mode)
• ON: N (Night mode)
Unless mode is in above setting, light signal (ON/OFF) may
not be accurately displayed.
• If vehicle speed is NG, refer to AV-114, "
Vehicle Speed Signal Inspection for NAVI Control Unit".
• If light is NG, refer to AV-116, "
Illumination Signal Inspection for NAVI Control Unit".
• If IGN is NG, refer to AV-117, "
Ignition Signal Inspection for NAVI Control Unit".
• If reverse is NG, refer to AV-117, "
Reverse Signal Inspection for NAVI Control Unit".
ERROR HISTORY
DIAGNOSIS BY ERROR HISTORY
The “Self-diagnosis” results indicate whether an error occurred during the period from when the ignition switch
is turned to ON until “Self-diagnosis” is completed.
If an error occurred before the ignition switch was turned to ON and does not occur again until the “Self-diag-
nosis” is completed, the diagnosis result will be judged normal. Therefore, those errors in the past which can-
not be found by the “Self-diagnosis” must be found by diagnosing the “Error History”.
WKIA4443E
Diagnosis item Display Condition Remarks
Vehicle speedON Vehicle speed > 0 km/h (0 MPH)
Changes in indication may be delayed by ap-
prox. 1.5 seconds. This is normal. OFF Vehicle speed = 0 km/h (0 MPH)
– Ignition switch in ACC position
LightsON Lighting switch ON
–
OFF Lighting switch OFF
IgnitionON Ignition switch ON
–
OFF Ignition switch ACC
ReverseON Selector lever in R position
Changes in indication may be delayed by ap-
prox. 1.5 seconds. This is normal. OFF Selector lever in other than R position
– Ignition switch in ACC position
WKIA4444E

AV-114
< SERVICE INFORMATION >
NAVIGATION SYSTEM
1. Disconnect AV switch connector.
2. Check voltage between connector terminals and ground as fol-
lows.
OK or NG
OK >> GO TO 3.
NG >> Check harness for open between AV switch and fuse.
3.CHECK GROUND CIRCUIT
Check continuity between AV switch and ground as follows.
OK or NG
OK >> Inspection End.
NG >> Repair or replace harness.
Vehicle Speed Signal Inspection for NAVI Control UnitINFOID:0000000003533728
1.CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit connector B152, combination
meter connector M24 and display control unit connector M94.
3. Check continuity between NAVI control unit harness connector
B152 (B) terminal 66 and combination meter harness connector
M24 (A) terminal 29.
4. Check continuity between NAVI control unit harness connector
B152 (B) terminal 66 and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness.
2.CHECK 1: VEHICLE SPEED SIGNAL
Terminals Ignition switch position
(+)
(–) OFF ACC ON
Connector Terminal
M981
GroundBattery
voltageBattery
voltageBattery
voltage
20VBattery
voltageBattery
voltage
WKIA1767E
Te r m i n a l s
Ignition switch Continuity
Connector Terminal —
M98 5 Ground OFF Yes
WKIA1768E
Continuity should exist.
Continuity should not exist.
WKIA4445E

NAVIGATION SYSTEM
AV-115
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
AV
N
O
P
1. Connect NAVI control unit connector.
2. Turn ignition switch ON.
3. Check voltage between NAVI control unit harness connector
B152 terminal 66 and ground.
OK or NG
OK >> GO TO 3.
NG >> Replace NAVI control unit. Refer to AV-145, "
Removal
and Installation".
3.CHECK 2: VEHICLE SPEED SIGNAL
1. Connect combination meter connector and display control unit
connector.
2. Drive vehicle at a constant speed.
3. Check signal between NAVI control unit harness connector
B152 terminal 66 and ground with CONSULT-ll or oscilloscope.
OK or NG
OK >> Replace NAVI control unit. Refer to AV-145, "Removal
and Installation".
NG >> Check combination meter system. Refer to DI-17, "
Vehicle Speed Signal Inspection".
Vehicle Speed Signal Inspection for Display Control UnitINFOID:0000000003533729
1.CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect display control unit connector M94, combination
meter connector M24 and NAVI control unit connector B152.
3. Check continuity between display control unit harness connector
M94 terminal 16 and combination meter harness connector M24
terminal 29.
4. Check continuity between display control unit harness connector
M94 terminal 16 and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness.
2.CHECK 1: VEHICLE SPEED SIGNALApprox. 3.5V or more
WKIA4209E
66 - Ground : Refer to AV-89, "Terminal
and Reference Value for NAVI
Control Unit".
WKIA4210E
Continuity should exist.
Continuity should not exist.
WKIA1506E

AV-116
< SERVICE INFORMATION >
NAVIGATION SYSTEM
1. Connect display control unit connector.
2. Turn ignition switch ON.
3. Check voltage between display control unit harness connector
M94 terminal 16 and ground.
OK or NG
OK >> GO TO 3.
NG >> Replace display control unit. Refer to AV-145, "
Removal
and Installation".
3.CHECK 2: VEHICLE SPEED SIGNAL
1. Connect combination meter connector M24 and NAVI control
unit connector B152.
2. Drive vehicle at a constant speed.
3. Check signal between display control unit harness connector
M94 terminal 16 and ground with CONSULT-ll or oscilloscope.
OK or NG
OK >> Replace display control unit. Refer to AV-145, "Removal
and Installation".
NG >> Check combination meter system. Refer to DI-17, "
Vehicle Speed Signal Inspection".
Illumination Signal Inspection for NAVI Control UnitINFOID:0000000003533730
1.CHECK ILLUMINATION SIGNAL
1. Turn the ignition switch ON.
2. Check voltage between NAVI control unit and ground.
OK or NG
OK >> Replace NAVI control unit. Refer to AV-145, "Removal
and Installation".
NG >> Check harness for open or short between NAVI control unit and IPDM E/R.
Illumination Signal Inspection for Display Control UnitINFOID:0000000003533731
1.CHECK ILLUMINATION SIGNALApprox. 3.5V or more
SKIA4297E
16 - Ground : Refer to AV-91, "Terminal
and Reference Value for Dis-
play Control unit".
SKIA4616E
Te r m i n a l s
Lighting switch position
(+)
(–)
Connector Terminal1st or 2nd po-
sitionOFF
B152 61 GroundBattery
voltageApprox. 0V
WKIA4211E

NAVIGATION SYSTEM
AV-117
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
AV
N
O
P
1. Turn ignition switch ON.
2. Check voltage between display control unit and ground.
OK or NG
OK >> Replace display control unit. Refer to AV-145, "Removal
and Installation".
NG >> Check harness for open or short between display control unit and IPDM E/R.
Ignition Signal Inspection for NAVI Control UnitINFOID:0000000003533732
1.CHECK IGNITION SIGNAL
1. Disconnect NAVI control unit connector B152.
2. Turn ignition switch ON.
3. Check voltage between NAVI control unit harness connector
B152 terminal 63 and ground.
OK or NG
OK >> Replace NAVI control unit. Refer to AV-145, "Removal
and Installation".
NG >> Check harness for open or short between NAVI control
unit and fuse.
Ignition Signal Inspection for Display Control UnitINFOID:0000000003533733
1.CHECK IGNITION SIGNAL
1. Disconnect display control unit connector M94.
2. Turn ignition switch ON.
3. Check voltage between display control unit harness connector
M94 terminal 12 and ground.
OK or NG
OK >> Replace display control unit. Refer to AV-145, "Removal
and Installation".
NG >> Check harness for open or short between display con-
trol unit and fuse.
Reverse Signal Inspection for NAVI Control UnitINFOID:0000000003533734
1.CHECK REVERSE LAMP
1. Turn ignition switch ON.
2. Place A/T selector lever into R-position. Do back-up lamps come on?
YES or NO
YES >> GO TO 2.
NO >> Check back-up lamp system. Refer to LT- 8 0
.
2.CHECK REVERSE SIGNAL
Te r m i n a l s
Lighting switch position
(+)
(–)
Connector Terminal1st or 2nd po-
sitionOFF
M94 14 GroundBattery
voltageApprox. 0V
SKIA4299E
Battery voltage should exist.
WKIA4212E
Battery voltage should exist.
WKIA1230E

AV-118
< SERVICE INFORMATION >
NAVIGATION SYSTEM
1. Disconnect NAVI control unit connector B152.
2. Turn ignition switch ON.
3. With the A/T selector lever in R-position, check voltage between
NAVI control unit and ground.
OK or NG
OK >> Replace NAVI control unit. Refer to AV-145, "Removal and Installation".
NG >> Check harness for open or short between NAVI control unit and back-up lamp position relay.
Reverse Signal Inspection for Display Control UnitINFOID:0000000003533735
1.CHECK REVERSE LAMP
1. Turn ignition switch ON.
2. Place A/T selector lever into R-position. Do back-up lamps come on?
YES or NO
YES >> GO TO 2.
NO >> Check back-up lamp system. Refer to LT- 8 0
.
2.CHECK REVERSE SIGNAL
1. Disconnect display control unit connector M94.
2. Turn ignition switch ON.
3. With the A/T selector lever in R-position, check voltage between
display control unit and ground.
OK or NG
OK >> Replace display control unit. Refer to AV-145, "Removal and Installation".
NG >> Check harness for open or short between display control unit and back-up lamp position relay.
AV Communication Line Check (Between Display Control Unit and NAVI Control Unit)
INFOID:0000000003533736
1.CHECK POWER SUPPLY AND GROUND CIRCUIT
Check power supply and ground circuit for NAVI control unit. Refer to AV-110, "
Power Supply and Ground Cir-
cuit Inspection for NAVI Control Unit".
OK or NG
OK >> GO TO 2.
NG >> Check the malfunctioning parts.
2.CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit connector B152 and display control unit connector M95.
3. Check continuity between NAVI control unit and display control unit.
Te r m i n a l s
Selector lever position
(+)
(–)
Connector Terminal R-positionOther than R-po-
sition
B152 65 Ground Battery voltage Approx. 0V
WKIA4213E
Te r m i n a l s
Selector lever position
(+)
(–)
Connector Terminal R-positionOther than
R-position
M94 6 Ground Battery voltage Approx. 0V
SKIA4303E

AV-120
< SERVICE INFORMATION >
NAVIGATION SYSTEM
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3.CHECK 1: AUDIO-TX COMMUNICATION SIGNAL
1. Connect display control unit connector.
2. Turn ignition switch ON.
3. Check voltage between display control unit harness connector
M95 terminal 42 and ground.
OK or NG
OK >> GO TO 4.
NG >> Replace display control unit. Refer to AV-145, "
Removal
and Installation".
4.CHECK 2: AUDIO-RX COMMUNICATION SIGNAL
1. Turn ignition switch OFF.
2. Disconnect display control unit connector M95.
3. Connect audio unit connector M45.
4. Turn ignition switch ON.
5. Check voltage between audio unit harness connector M45 ter-
minal 65 and ground.
OK or NG
OK >> GO TO 5.
NG >> Replace audio unit. Refer to AV-46, "
Removal and
Installation".
5.CHECK 3: AUDIO-TX COMMUNICATION SIGNAL
Check signal between display control unit harness connector M95
terminal 40 and ground with CONSULT-ll or oscilloscope.
OK or NG
OK >> GO TO 6.
NG >> Replace display control unit. Refer to AV-145, "
Removal
and Installation".
6.CHECK 4: AUDIO-RX COMMUNICATION SIGNAL
1. Turn ignition switch ON.
2. Check signal between display control unit harness connector
M95 terminal 42 and ground with CONSULT-ll or oscilloscope.
OK or NG
OK >> Inspection End.
NG >> Replace audio unit. Refer to AV-46, "
Removal and
Installation". Approx. 3.5V or more.
WKIA1770E
Approx. 3.5V or more.
WKIA1771E
40 - Ground : Refer to AV-91, "Terminal
and Reference Value for Dis-
play Control unit".
SKIA4447E
42 - Ground : Refer to AV-91, "Terminal
and Reference Value for Dis-
play Control unit".
SKIA4448E