air condition INFINITI QX56 2008 Factory Owner's Manual

ADP-96
< COMPONENT DIAGNOSIS >
TILT MOTOR
OK or NG
OK >> Replace tilt motor. Refer to ST-19, "Removal and Installation".
NG >> GO TO 3
3. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit.
NO >> Repair or replace the malfunctioning part.
Connector Te r m i n a l s
ConditionVoltage (V)
(Approx.)
(+) (-)
M34 35
Ground ADP steering switch ON
(UP operation)
Battery voltage
Other than above 0
42 ADP steering switch ON
(DOWN operation)
Battery voltage
Other than above 0
Revision: March 2010 2008 QX56

ADP-100
< COMPONENT DIAGNOSIS >
DOOR MIRROR MOTOR
Door mirror RH
4. Check continuity between automatic drive positioner control unitconnector and ground.
Door mirror LH
Door mirror RH
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1. Connect automatic drive positioner control unit.
2. Turn ignition switch ON.
3. Check voltage between automatic drive positioner control unit connector and ground.
Door mirror LH
Automatic drive posi-
tioner control unit con- nector Te r m i n a l
Door mirror
RH connector Terminal Continuity
M33 14
D107 1
Ye s
15 2
30 3
Automatic drive position- er control unit connector Te r m i n a l
GroundContinuity
M33 16
No
31
32
Automatic drive position- er control unit connector Te r m i n a l
GroundContinuity
M33 14
No
15
30
LIIA1888E
Te r m i n a l s
Mirror switch condition Voltage (V)
(Approx.)
(+)
(-)
Automatic drive
positioner control unit connector Te r m i n a l
M33 16
Ground DOWN / RIGHT Battery voltage
Other than above 0
31 UP
Battery voltage
Other than above 0
32 LEFT
Battery voltage
Other than above 0
ALJIA0197ZZ
Revision: March 2010 2008 QX56

BCM (BODY CONTROL MODULE)ADP-141
< ECU DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
BCM (BODY CONTROL MODULE)
Reference ValueINFOID:0000000004832378
VALUES ON THE DIAGNOSIS TOOL
Monitor Item Condition Value/Status
AIR COND SW A/C switch OFF
OFF
A/C switch ON ON
AUT LIGHT SYS Outside of the room is dark
OFF
Outside of the room is bright ON
AUTO LIGHT SW Lighting switch OFF
OFF
Lighting switch AUTO ON
BACK DOOR SW Back door closed
OFF
Back door opened ON
CDL LOCK SW Door lock/unlock switch does not operate
OFF
Press door lock/unlock switch to the LOCK side ON
CDL UNLOCK SW Door lock/unlock switch does not operate
OFF
Press door lock/unlock switch to the UNLOCK side ON
DOOR SW-AS Front door RH closed
OFF
Front door RH opened ON
DOOR SW-DR Front door LH closed
OFF
Front door LH opened ON
DOOR SW-RL Rear door LH closed
OFF
Rear door LH opened ON
DOOR SW-RR Rear door RH closed
OFF
Rear door RH opened ON
ENGINE RUN Engine stopped
OFF
Engine running ON
FR FOG SW Front fog lamp switch OFF
OFF
Front fog lamp switch ON ON
FR WASHER SW Front washer switch OFF
OFF
Front washer switch ON ON
FR WIPER LOW Front wiper switch OFF
OFF
Front wiper switch LO ON
FR WIPER HI Front wiper switch OFF
OFF
Front wiper switch HI ON
FR WIPER INT Front wiper switch OFF
OFF
Front wiper switch INT ON
FR WIPER STOP Any position other than front wiper stop position
OFF
Front wiper stop position ON
HAZARD SW When hazard switch is not pressed
OFF
When hazard switch is pressed ON
LIGHT SW 1ST Lighting switch OFF
OFF
Lighting switch 1st ON
Revision: March 2010 2008 QX56

ADP-160
< ON-VEHICLE MAINTENANCE >
PRE-INSPECTION FOR DIAGNOSTIC
ON-VEHICLE MAINTENANCE
PRE-INSPECTION FOR DIAGNOSTIC
Basic InspectionINFOID:0000000001735563
1. CHECK POWER SUPPLY AND DROUND CIRCUIT
Check the power supply and ground circuit as shown below.
• Driver seat control unit :Refer to ADP-44, "
DRIVER SEAT CONTROL UNIT : DiagnosisProcedure".
• Automatic drive positioner control unit: Refer to ADP-45, "
AUTOMATIC DRIVE POSITIONER CONTROL
UNIT : DiagnosisProcedure".
Is the inspection result normally?
YES >> GO TO 2
NO >> Repair or replace the malfunctioning part.
2. CHECK MANUAL FUNCTION
Check the manual function operations by operati ng the relevant switches as shown below.
• Seat (slide, reclining, lifting front, lifting rear)
• Pedal assembly (forward, backward)
• Steering wheel (upward, downward)
• Door mirror
Do all manual functions operate normally?
YES >> GO TO 3
NO (Seat, pedal, door mirror)>>Go to SYMPTOM 1, refer to ADP-155, "
Symptom Table". And, GO TO 4 if
the result of SYMPTOM 1 is OK.
3. CHECK MEMORY FUNCTION 1
Register the seat positions (refer to Owner’s Manual) and check that all parts of the seat, pedals, steering
wheel and door mirrors move to their memory positions correctly.
Are the operations normal?
YES >> Check each malfunction according to the instruction of the SYMPTOM 4, refer to ADP-155,
"Symptom Table".
No (memory indicator operates normally)>> Go to SYMPTOM 2, refer to ADP-155, "
Symptom Table".
No (memory indicator does not operate normally either)>> GO TO 5
4. CHECK MEMORY FUNCTION 2
Register the seat positions (refer to Owner’s Manual) and check that all parts of the seat, pedals, steering
wheel and door mirrors move to their memory positions correctly.
Are the operations normal?
YES >> Check intermittent incident. Refer to GI-38, "Intermittent Incident".
NO >> GO TO 7
5. CHECK SEAT MEMORY SWITCH/MEMORY INDICATOR
Check the seat memory switch/memory switch indicator of the SYMPTOM 5, refer to ADP-155, "
Symptom
Table".
Is the inspection result normal?
YES >> GO TO 6
NO >> Repair or replace the malfunctioning part.
6. CHECK OPERATION CONDITION
Check the memory operation conditions (refer to ADP-10, "
AUTOMATIC DRIVE POSITIONER SYSTEM :
System Description").
Are all operation conditions fulfilled?
YES >> Go to SYMPTOM 6, refer to ADP-155, "Symptom Table".
NO >> Fulfill the operation conditions. Refer to ADP-10, "
AUTOMATIC DRIVE POSITIONER SYSTEM :
System Description".
Revision: March 2010 2008 QX56

AV
AV-3
C
DE
F
G H
I
J
K L
M B
A
O P
Description ..........................................................
....
76
Diagnosis Procedure ...............................................76
RGB AREA (YS) SIGNAL CIRCUIT ..................77
Description .......................................................... ....77
Diagnosis Procedure ...............................................77
HORIZONTAL SYNCHRONIZING (HP) SIG-
NAL CIRCUIT ................................................. ....
78
Description .......................................................... ....78
Diagnosis Procedure ...............................................78
VERTICAL SYNCHRONIZING (VP) SIGNAL
CIRCUIT ......................................................... ....
79
Description .......................................................... ....79
Diagnosis Procedure ...............................................79
FRONT DOOR SPEAKER .................................80
Description .......................................................... ....80
Diagnosis Procedure ...............................................80
FRONT TWEETER .............................................83
Description .......................................................... ....83
Diagnosis Procedure ...............................................83
CENTER SPEAKER ...........................................86
Description .......................................................... ....86
Diagnosis Procedure ...............................................86
REAR DOOR SPEAKER ....................................88
Description .......................................................... ....88
Diagnosis Procedure ...............................................88
REAR DOOR TWEETER ...................................91
Description .......................................................... ....91
Diagnosis Procedure ...............................................91
BACK DOOR SPEAKER ...................................94
Description .......................................................... ....94
Diagnosis Procedure ...............................................94
SUBWOOFER ....................................................97
Description .......................................................... ....97
Diagnosis Procedure ...............................................97
AMP ON SIGNAL CIRCUIT .............................100
Description .......................................................... ..100
Diagnosis Procedure .............................................100
STEERING SWITCH ........................................101
Description .......................................................... ..101
Diagnosis Procedure .............................................101
MICROPHONE SIGNAL CIRCUIT ...................103
Description .......................................................... ..103
Diagnosis Procedure .............................................103
ECU DIAGNOSIS .......................................105
AV CONTROL UNIT ....................................... ..105
Reference Value ................................................. ..105
Wiring Diagram .....................................................111
DTC Index ........................................................... ..139
DISPLAY UNIT ................................................141
Reference Value ....................................................141
BOSE SPEAKER AMP ...................................144
Reference Value ....................................................144
REAR VIEW CAMERA CONTROL UNIT .......147
Reference Value ....................................................147
DVD PLAYER ..................................................149
Reference Value ....................................................149
SYMPTOM DIAGNOSIS ............................151
MULTI AV SYSTEM ........................................151
Symptom Table ................................................... ..151
NORMAL OPERATING CONDITION .............153
Description .............................................................153
PRECAUTION ............................................161
PRECAUTIONS ...............................................161
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ..
161
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect .................................
161
PREPARATION .........................................163
PREPARATION ...............................................163
Commercial Service Tools ................................... ..163
ON-VEHICLE REPAIR ...............................164
AV CONTROL UNIT ........................................164
Removal and Installation ..................................... ..164
DISPLAY UNIT ................................................166
Removal and Installation .......................................166
FRONT TWEETER ..........................................167
Removal and Installation .......................................167
CENTER SPEAKER ........................................168
Removal and Installation .......................................168
FRONT DOOR SPEAKER ..............................169
Removal and Installation .......................................169
REAR DOOR SPEAKER ................................170
Removal and Installation .......................................170
BACK DOOR SPEAKER ................................171
Removal and Installation .......................................171
SUBWOOFER .................................................172
Removal and Installation .......................................172
DVD PLAYER ..................................................173
Removal and Installation .......................................173
Revision: March 2010 2008 QX56

AV
DIAGNOSIS AND REPAIR WORKFLOWAV-5
< BASIC INSPECTION > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work FlowINFOID:0000000001696015
OVERALL SEQUENCE
• Reference 1··· Refer to AV-33, "AV CONTROL UNIT : CONSULT-III Function".
• Reference 2··· Refer to AV-151, "
Symptom Table".
DETAILED FLOW
1.CHECK SYMPTOM
Check the malfunction symptoms by performing the following items.
• Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred).
• Check the symptom.
>> GO TO 2
2.SELF-DIAGNOSIS (CONSULT-III)
1. Connect CONSULT-III and perform “SELF-DIAGNOSIS” for “MULTI AV”. NOTE:
Skip to step 4 of the diagnosis proc edure if “MULTI AV” is not displayed.
2. Check if any DTC No. is displayed in the self-diagnosis results.
AWNIA0030GB
Revision: March 2010 2008 QX56

AV
INSPECTION AND ADJUSTMENTAV-7
< BASIC INSPECTION > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
INSPECTION AND ADJUSTMENT
REAR VIEW MONITOR GUIDING LINE ADJUSTMENT
REAR VIEW MONITOR GUIDING LI NE ADJUSTMENT : DescriptionINFOID:0000000001696016
This mode is used to modify the side distance guidelines if they are dislocated from the rear view monitor
image, because of variations of body/camera mounting conditions.
REAR VIEW MONITOR GUIDING LINE ADJU STMENT : Special Repair Requirement
INFOID:0000000001696017
1. Create a correction line to modify the screen.
Draw lines on the rearward of the vehicle passing through the
following points: 200 mm (7.87 inch) from both sides of the vehi-
cle, and
• *1: 0.5 m (1.5 feet)
• *2: 1 m (3 feet)
• *3: 2 m (7 feet)
• *4: 3 m (10 feet)and from the rear end of the bumper
2. With the ignition switch OFF, connect CONSULT-III, then turn
ignition switch ON. Select “REARVIEW CAMERA”.
CAUTION:
Stop engine for safety when correcting side distance guide-
line.
3. Shift the A/T selector lever to R position.
4. Touch “SELCT GUIDELINE PATTERN” under “WORK SUPPORT” menu.
5. Touch “UP” or “DOWN”, and select the guide line, “PATTERN NO. 0” or “PATTERN NO. 1”, which is the
closest to the corrected line.
6. Touch “SAVE”, and confirm the guide line.
7. Touch “END”.
8. Touch “ADJ GUIDELINE POSITION” under the “WORK SUPPORT” menu.
9. Adjust the guide line touching “X UP”, “X DOWN”, “Y UP” or “Y DOWN” so that the corrected line can fit the guide line.
10. Touch “SAVE”, and confirm the guide line.
SKIA5637E
SKIA6103E
Revision: March 2010 2008 QX56

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)AV-29
< FUNCTION DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
XM SAT SUBSCRIPTION STATUS
The XM NavTraffic subscription status can be checked.
Error History
The self-diagnosis results are judged depending on whether any
error occurs from when “Self-diagnosis” is selected until the self-
diagnosis results are displayed.
However, the diagnosis results are judged normal if an error has
occurred before the ignition SW is turned ON and then no error has
occurred until the self-diagnosis star t. Check the “Error History” to
detect any error that may have occurred before the self-diagnosis
start because of this situation.
Count up method A
• The counter resets to 0 if an error occurs when IGN switch is turned ON. The counter increases by 1 if thecondition is normal at
a next IGN ON cycle.
• The counter upper limit is 39. Any counts exceeding 39 are ignored. The counter can be reset (no error-
record display) with the “Delete log” switch or CONSULT-III.
Count up method B
• The counter increases by 1 if an error occurs when IGN switch is ON. The counter will not decrease even
ifthe condition is normal at the next IGN ON cycle.
• The counter upper limit is 50. Any counts exceeding 50 are ignored. The counter can be reset (no error-
record display) with the “Delete log” switch or CONSULT-III.
Error item
Some error items may be displayed simultaneously accordi ng to the cause. If some error items are displayed
simultaneously, the detection of the cause can be per formed by the combination of display items
ALNIA0225GB
Display method of occur-
rence frequency Error history diplay item
Count up method A CAN communication line, control unit (CAN), AV communication line, control unit (AV communica-
tion)
Count up method B Other than above
Error item DescriptionPossible malfunction factor/Action to take
CAN COMM CIRCUIT CAN communication malfunction is detect-
edPerform diagnosis with CONSULT-III, and
then repair the malfunctioning parts accord-
ing to the diagnosis results.
Refer to AV- 3 3 , "
AV CONTROL UNIT :
CONSULT-III Function".
ALNIA0226GB
Revision: March 2010
2008 QX56

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)AV-33
< FUNCTION DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
Deletes any unit connection records and error records from the AV
control unit memory. (Clear the records of the unit that has been
removed)
Inititialize Settings
Initializes the AV control unit memory.
AV CONTROL UNIT : CONSULT-III FunctionINFOID:0000000001696039
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
Self-diagnosis results
• In CONSULT-III self-diagnosis, self-diagnosis results and error history are displayed collectively.
• The current malfunction indicates “CRNT”. The past malfunction indicates “PAST”.
• The timing is displayed as “0” if any of the error codes [U1000], [U1010], [U1300] and [U1310] is detected.
The counter increases by 1 if the condition is normal at the next ignition switch ON cycle.
Self-diagnosis results display item
ALNIA0239GB
ALNIA0240GB
MULTI AV diagnosis mode Description
SELF-DIAG RESULTS Displays AV control unit self-diagnosis results.
DATA MONITOR Displays AV control unit input/output data in real time.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
AV COMM MONITOR Allows the technician to monitor the status of the Multi AV system communication signals.
ECU PART NUMBER The part number of AV control unit can be checked.
Error item DescriptionPossible malfunction factor/Action to take
CAN COMM CIRCUIT[U1000] CAN communication malfunction is detect-
edPerform diagnosis with CONSULT-III, and
then repair the malfunctioning parts accord-
ing to the diagnosis results.
Refer to AV- 3 3 , "
AV CONTROL UNIT :
CONSULT-III Function".
Revision: March 2010
2008 QX56

AV
U121F AV CONTROL UNITAV-53
< COMPONENT DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
U121F AV CONTROL UNIT
DescriptionINFOID:0000000001696077
DTC LogicINFOID:0000000001696078
Diagnosis ProcedureINFOID:0000000001696079
1.CHECK AV CONTROL UNIT POWE R SUPPLY AND GROUND CIRCUIT
Check audio control unit power supply and ground circuit. Refer to AV-63, "
AV CONTROL UNIT : Diagnosis
Procedure".
Is inspection result OK?
YES >> Inspection end.
NO >> Repair malfunctioning parts.
Part name Description
AV CONTROL UNIT • Integrates HDD (hard disk
drive) allowing map data and music data to be
stored.
• It is the master unit of the MULTI AV system, and it is connected to each control
unit by means of communication. It operates each system according to com-
munication signals from the AV control unit.
• The AV control unit includes the audio, hands-free phone, voice control, navi-
gation, and vehicle information functions.
• It is connected to ECM and combination meter via CAN communication to ob- tain necessary information for the vehicle information function.
• It inputs the automatic brightness ON/OFF signals that are required for the dis- play dimming control.
• It inputs the signals for driving status recognition (vehicle speed, reverse and parking brake).
DTC Display contents of
CONSULT-III DTC Detection Condition
Action to take
U121F INTERNAL COMM
[U121F] Internal malfunction of AV control unit (internal communi-
cation error) is detected. AV control unit power supply and
ground circuit.
Revision: March 2010
2008 QX56