INFINITI QX56 2010 Factory Service Manual

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)BRC-99
< ECU DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Fail-SafeINFOID:0000000005148083
CAUTION:
If the Fail-Safe function is activated, perform Self Di agnosis for ABS/TCS/VDC system.
ABS/EBD SYSTEM
ABFIA0020GB
Revision: April 20092010 QX56

BRC-100
< ECU DIAGNOSIS >[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
In case of an electrical malfunction with the ABS, t
he ABS warning lamp, VDC OFF indicator lamp and SLIP
indicator lamp will turn on. In case of an electrical malfunction with the EBD system, the BRAKE warning lamp,
ABS warning lamp, VDC OFF indicator lamp and SLIP indicator lamp will turn on.
The system will revert to one of the follo wing conditions of the Fail-Safe function.
1. For ABS malfunction, only the EBD is operative and the condition of the vehicle is the same condition of vehicles without ABS/TCS/VDC system.
2. For EBD malfunction, the EBD and ABS become inoperat ive, and the condition of the vehicle is the same
as the condition of vehicles without ABS/TCS/VDC or EBD system.
VDC/TCS SYSTEM
In case of TCS/VDC system malfunction, the VDC OFF indicator lamp and SLIP indicator lamp are turned on
and the condition of the vehicle is the same as the c ondition of vehicles without TCS/VDC system. In case of
an electrical malfunction with the TCS/VDC system, the ABS control continues to operate normally without
TCS/VDC control.
DTC No. IndexINFOID:0000000005148084
DTC Items (CONSULT screen terms) Reference
C1101 RR RH SENSOR-1
BRC-28, "
Description"C1102RR LH SENSOR-1
C1103 FR RH SENSOR-1
C1104 FR LH SENSOR-1
C1105 RR RH SENSOR-2
BRC-31, "
Description"C1106RR LH SENSOR-2
C1107 FR RH SENSOR-2
C1108 FR LH SENSOR-2
C1109 BATTERY VOLTAGE [ABNORMAL] BRC-34, "
Description"
C1110CONTROLLER FAILURE BRC-36, "DTC Logic"
C 1111P U M P M O T O R BRC-37, "Description"
C1113G-SENSOR BRC-39, "Description"
C1115ABS SENSOR [ABNORMAL SIGNAL] BRC-42, "Description"
C1116STOP LAMP SW BRC-45, "Description"
C1120FR LH IN ABS SOL BRC-47, "Description"
C1121FR LH OUT ABS SOL BRC-50, "Description"
C1122FR RH IN ABS SOL BRC-47, "Description"
C1123FR RH OUT ABS SOL BRC-50, "Description"
C1124RR LH IN ABS SOL BRC-47, "Description"
C1125RR LH OUT ABS SOL BRC-50, "Description"
C1126RR RH IN ABS SOL BRC-47, "Description"
C1127RR RH OUT ABS SOL BRC-50, "Description"
C1130ENGINE SIGNAL 1
BRC-53, "
Description"
C1131ENGINE SIGNAL 2
C1132 ENGINE SIGNAL 3
C1133 ENGINE SIGNAL 4
C1136 ENGINE SIGNAL 6
C1140 ACTUATOR RLY BRC-55, "
Description"
C1142PRESS SEN CIRCUIT BRC-57, "Description"
C1143ST ANG SEN CIRCUIT
BRC-60, "Description"C1144ST ANG SEN SIGNAL
Revision: April 20092010 QX56

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)BRC-101
< ECU DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1145 YAW RATE SENSOR
BRC-39, "Description"C1146SIDE G-SEN CIRCUIT
C1155 BR FLUID LEVEL LOW BRC-63, "
Description"
C1156ST ANG SEN COM CIR BRC-66, "Description"
C1160DECEL G SEN SET BRC-67, "Description"
C1163ST ANGL SEN SAFE BRC-68, "Description"
C1164CV1
BRC-69, "
Description"C1165CV2
C1166 SV1
C1167 SV2
C1170 VARIANT CODING BRC-36, "
DTC Logic"
C1178ABS ACTIVE BOOSTER SV NG BRC-72, "Description"
C1179ABS DELTA S SEN NG BRC-75, "Description"
C1181ABS ACTIVE BOOSTER RESPONSE NG
BRC-72, "Description"C1184ABS BRAKE RELEASE SW NG
C1185 ABS ACC CU INTERNAL NG BRC-77, "
Description"
C1189ABS BRAKE BOOSTER DEFECT BRC-72, "Description"
U1000CAN COMM CIRCUIT BRC-79, "Description"
DTCItems (CONSULT screen terms) Reference
Revision: April 20092010 QX56

BRC-102
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
VDC/TCS/ABS
SYMPTOM DIAGNOSIS
VDC/TCS/ABS
Symptom TableINFOID:0000000005148085
If ABS warning lamp, VDC OFF indicator lamp and SLIP indicator lamp turn ON, perform self-diagnosis.
NOTE:
• 1: The ABS does not operate when the speed is 10 km/h (6 MPH) or less.
• 2: Under the following conditions, ABS is activated and vibration is felt when brake pedal is lightly depressed. However, this
is normal.
- When shifting gears
- When driving on slippery road
- During cornering at high speed
- When passing over bumps or grooves [at approximately 50 mm (1.97 in) or more]
- When pulling away just after starting engine [at approximately 10 km/h (6 MPH) or higher] Symptom
Check itemReference
Excessive ABS function operation fre-
quency Brake force distribution
BRC-103, "
Diag-
nosis Procedure"Looseness of front and rear axle
Wheel sensor and rotor system
Unexpected pedal reaction Brake pedal stroke
BRC-104, "
Diag-
nosis Procedure"Make sure the braking force is sufficient when the ABS is not operating.
The braking distance is long Check stopping distance when the ABS is not operating. BRC-105, "
Diag-
nosis Procedure"
ABS function does not operate (Note 1) ABS actuator and electric
unit (control unit)BRC-106, "Diag-
nosis Procedure"
Pedal vibration or ABS operation sound
occurs (Note 2)Brake pedal
BRC-107, "Diag-
nosis Procedure"ABS actuator and electric unit (control unit)
Vehicle jerks during VDC/TCS/ABS con-
trol ABS actuator and electric unit (control unit)
BRC-108, "
Diag-
nosis Procedure"TCM
ECM
Revision: April 20092010 QX56

EXCESSIVE ABS FUNCTION OPERATION FREQUENCYBRC-103
< SYMPTOM DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
Diagnosis ProcedureINFOID:0000000005148086
1.CHECK START
Check front and rear brake force di stribution using a brake tester.
Is the inspection result normal?
YES >> GO TO 2
NO >> Check brake system.
2.CHECK FRONT AND REAR AXLE
Make sure that there is no excessive play in the front and rear axles. Refer to front: FAX-6, "
On-Vehicle
Inspection and Service", Rear: RAX-6, "On-Vehicle Inspection and Service".
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace malfunctioning components.
3.CHECK WHEEL SENSOR AND SENSOR ROTOR
Check the following.
• Wheel sensor installation for damage.
• Sensor rotor installation for damage.
• Wheel sensor connector connection.
• Wheel sensor harness inspection.
Is the inspection result normal?
YES >> GO TO 4
NO >> • Replace wheel sensor or sensor rotor. Refer to BRC-114, "
Removal and Installation".
• Repair harness.
4.CHECK ABS WARNING LAMP DISPLAY
Make sure that the ABS warning lamp is turned off af ter the ignition switch is turned ON or when driving.
Is the ABS warning lamp illuminated?
YES >> Perform self-diagnosis. Refer to BRC-23, "CONSULT-III Function (ABS)".
NO >> Normal
Revision: April 20092010 QX56

BRC-104
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
UNEXPECTED PEDAL REACTION
UNEXPECTED PEDAL REACTION
Diagnosis ProcedureINFOID:0000000005148087
1.CHECK BRAKE PEDAL STROKE
Check brake pedal stroke. Refer to BR-15, "
Inspection and Adjustment".
Is the stroke too large?
YES >> • Bleed air from brake tube and hose. Refer to BR-17, "Bleeding Brake System".
• Check brake pedal, brake booster, and master cylinder for mount play, looseness, brake system fluid leakage, etc. Refer to BR-15, "
Inspection and Adjustment" (brake pedal), BR-12, "On
Board Inspection" (master cylinder), BR-10, "Inspection" (brake booster).
NO >> GO TO 2
2.CHECK FUNCTION
Disconnect ABS actuator and electric unit (control unit) c onnector to deactivate ABS. Check if braking force is
normal in this condition. Connect connector after inspection.
Is the inspection result normal?
YES >> Normal
NO >> Check brake system.
Revision: April 20092010 QX56

THE BRAKING DISTANCE IS LONGBRC-105
< SYMPTOM DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
THE BRAKING DISTANCE IS LONG
Diagnosis ProcedureINFOID:0000000005148088
CAUTION:
The stopping distance on slippery road surfaces might be longer with the ABS operating than when
the ABS is not operating.
1.CHECK FUNCTION
Turn ignition switch OFF and disconnect ABS actuator and electric unit (control unit) connector to deactivate
ABS. In this condition, check stopping di stance. After inspection, connect connector.
Is the inspection result normal?
YES >> Normal
NO >> Check brake system.
Revision: April 20092010 QX56

BRC-106
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
ABS FUNCTION DOES NOT OPERATE
ABS FUNCTION DOES NOT OPERATE
Diagnosis ProcedureINFOID:0000000005148089
CAUTION:
ABS does not operate when speed
is 10 km/h (6 MPH) or lower.
1.CHECK ABS WARNING LAMP DISPLAY
Make sure that the ABS warning lamp turns OFF af ter ignition switch is turned ON or when driving.
Is the inspection result normal?
YES >> Normal
NO >> Perform self-diagnosis. Refer to BRC-23, "
CONSULT-III Function (ABS)".
Revision: April 20092010 QX56

PEDAL VIBRATION OR ABS OPERATION SOUND OCCURS
BRC-107
< SYMPTOM DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
PEDAL VIBRATION OR ABS OPERATION SOUND OCCURS
Diagnosis ProcedureINFOID:0000000005148090
CAUTION:
Under the following conditions, ABS is activated an d vibration is felt when brake pedal is lightly
depressed. However, this is normal.
• When shifting gears
• When driving on slippery road
• During cornering at high speed
• When passing over bumps or grooves [at approximately 50 mm (1.97 in) or more]
• When pulling away just after starting engine [at approximately 10 km/h (6 MPH) or higher]
1.SYMPTOM CHECK 1
Check that there are pedal vibrat ions when the engine is started.
Do vibrations occur?
YES >> GO TO 2
NO >> Inspect the brake pedal.
2.SYMPTOM CHECK 2
Check that there are ABS operation noises when the engine is started.
Do the operation noises occur?
YES >> GO TO 3
NO >> Perform self -diagnosis. Refer to BRC-23, "
CONSULT-III Function (ABS)".
3.SYMPTOM CHECK 3
Check symptoms when electrical component (headlamps, etc.) switches are operated.
Do symptoms occur?
YES >> Check if there is a radio, antenna, antenna lead wire, or wiring close to the control unit. If there is,
move it farther away.
NO >> Normal
Revision: April 20092010 QX56

BRC-108
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
VEHICLE JERKS DURING VDC/TCS/ABS CONTROL
VEHICLE JERKS DURING
VDC/TCS/ABS CONTROL
Diagnosis ProcedureINFOID:0000000005148091
1.SYMPTOM CHECK
Check if the vehicle jerks during VDC/TCS/ABS control.
Is the inspection result normal?
YES >> Normal.
NO >> GO TO 2
2.CHECK SELF-DIAGNOSIS RESULTS
Perform self-diagnosis of ABS actuator and electric unit (control unit). Refer to \
BRC-23, "
CONSULT-III Func-
tion (ABS)".
Are self-diagnosis results indicated?
YES >> Check corresponding items, make repairs, and perform ABS actuator and electric unit (control
unit) self-diagnosis. Refer to BRC-23, "
CONSULT-III Function (ABS)".
NO >> GO TO 3
3.CHECK CONNECTOR
• Turn ignition switch OFF and disconnect ABS actuator and electric unit (control unit) connector and check
terminal for deformation, disconnection, looseness, etc.
• Securely connect connectors and perform ABS actuator and electric unit (control unit) self-diagnosis. Refer
to BRC-23, "
CONSULT-III Function (ABS)".
Are self-diagnosis results indicated?
YES >> If poor contact, damage, open or short circuit of connector terminal is found, repair or replace.
NO >> GO TO 4
4.CHECK ECM AND TCM SELF-DIAGNOSIS RESULTS
Perform ECM and TCM self-diagnosis.
Are self-diagnosis results indicated?
YES >> Check the corresponding items. • ECM: Refer to EC-63, "
CONSULT-III Function (ENGINE)".
• TCM: Refer to TM-32, "
CONSULT-III Function (TRANSMISSION)".
NO >> Replace ABS actuator and electric unit (control unit). Refer to BRC-116, "
Removal and Installa-
tion".
Revision: April 20092010 QX56