INFINITI QX56 2011 Factory Service Manual

DAS-406
< REMOVAL AND INSTALLATION >[LDW & LDP]
WARNING BUZZER
WARNING BUZZER
Removal and InstallationINFOID:0000000006223846
REMOVAL
1. Remove the instrument lower panel (LH). Refer to
IP-14, "Removal and Installation".
2. Remove the screw.
3. Remove warning buzzer.
INSTALLATION
Install in the reverse order of removal.
Revision: 2010 May2011 QX56

DAS
PRECAUTIONSDAS-407
< PRECAUTION > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006223847
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
 To avoid rendering the SRS inoper ative, which could increase the risk of personal injury or death in
the event of a collision that would result in air ba g inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
 Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintentional act ivation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
 Do not use electrical test equipm ent on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
 When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
 When using air or electric power tools or hammers , always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for BSW System ServiceINFOID:0000000006223848
WARNING:
Be careful of traffic conditions and safety aro und the vehicle when performing road test.
CAUTION:
 Never perform the active test while driving.
 Never change BSW initial state ON ⇒ OFF without the consent of the customer.
TO KEEP THE BSW SYSTEM OPERATING PROPERLY, BE SURE TO OBSERVE THE FOLLOW-
ING ITEMS:
System Maintenance
The two side radar for the BSW system are located near the rear bumper.
 Always keep the area near the side radar clean.
 Do not attach stickers (including transparent material ), install accessories or apply additional paint near the
side radar.
 Do not strike or damage the area around the side radar.
Revision: 2010 May2011 QX56

DAS-408
< SYSTEM DESCRIPTION >[BSW]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000006223849
1. Side radar RH 2. BCM
Refer to BCS-4, "
BODY CONTROL
SYSTEM : Component Parts Loca-
tion"
3. TCM
Refer to TM-10, "
A/T CONTROL
SYSTEM : Component Parts Loca-
tion"
4. ABS actuator and el ectric unit (con-
trol unit)
Refer to BRC-10, "
Component Parts
Location"
5. ADAS control unit
Refer to DAS-13, "
Component Parts
Location"
6. Side radar LH
7. BSW indicator RH 8. BSW warning lamp (On the combination meter)9. BSW indicator LH
10. Warning systems switch 11. Warning systems ON indicator 12. Warning buzzer
JSOIA0370ZZ
Revision: 2010 May2011 QX56

DAS
COMPONENT PARTSDAS-409
< SYSTEM DESCRIPTION > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
Component DescriptionINFOID:0000000006223850
A. Rear bumper removed condition B. Rear bumper removed condition C. Instrument lower panel (LH)
D. Behind of instrument lower panel (LH)
Component Description
ADAS control unit  Being connected with side radar (LH and RH) via ITS communication, receives vehicle detection
signal and transmits BSW indicator signal and BSW indicator dimmer signal to side radar
 Activates the warning buzzer and warning systems ON indicator
Side radar LH/ RH  Being connected with ADAS control unit via ITS communication, transmits vehicle detection sig-
nal
 Receives BSW indicator signal and BSW indicator dimmer signal from ADAS control unit and transmits an indicator operation signal to BSW indicator LH/RH
 RH side radar equips right/left switching signal circuit for identifying LH or RH because the parts
of side radar are common for right and left
BSW indicator LH/ RH Receives BSW indicator operation signal from side radar LH/RH and turns OFF, turns ON or blinks
ABS actuator and electric unit
(control unit) Transmits vehicle speed signal to ADAS control unit via CAN communication
Warning systems switch Inputs the switch signal to ADAS control unit
Warning systems ON indicator
(On the warning systems switch) Indicates BSW system status
Warning buzzer Receives buzzer signal from ADAS control unit and sounds buzzer.
Combination meter  Receives BSW warning lamp signal via CAN communication
 Turns the BSW warning lamp ON/OFF according to the signals from the ADAS control unit via
CAN communication
BCM  Transmits turn indicator signal to ADAS control unit via CAN communication
 Transmits dimmer signal to ADAS control unit via CAN communication
TCM Transmits the shift position signal to ADAS control unit via CAN communication
Revision: 2010 May2011 QX56

DAS-410
< SYSTEM DESCRIPTION >[BSW]
SYSTEM
SYSTEM
System DescriptionINFOID:0000000006223851
SYSTEM DIAGRAM
ADAS CONTROL UNIT INPU
T/OUTPUT SIGNAL ITEM
ADAS control unit receives signals via CAN communication. It also detects vehicle conditions that are neces-
sary for BSW control.
Input Signal Item
Output Signal Item
JSOIA0378GB
Transmit unit Signal name Description
TCM CAN communication Shift position signal Receives a selector lever position
ABS actuator
and electric unit
(control unit) CAN communication Vehic
le speed signal (ABS)Receives wheel speeds of four wheels
BCM CAN communication Turn indicator signal
Receives an operational state of the turn signal lamp and
the hazard lamp
Dimmer signal Receives ON/OFF state of dimmer signal
Side radar LH,
RH ITS communication Vehicle detection signal Receives vehicle detection condition of detection zone
Warning sys-
tems switch Warning systems switch signal Receives an ON/OFF state of the warning systems
switch
Reception unit Signal name Description
Combination
meter CAN communication BSW
warning lamp signalTransmits a BSW warning lamp signal to turn ON the
BSW warning lamp
Side radar LH,
RH ITS communication BSW indicator signal
Transmits a BSW indicator signal to turn ON the BSW
indicator
BSW indicator dimmer signal Transmits a BSW indicator dimmer signal to dimmer
BSW indicator
Vehicle speed signal Transmits a vehicle speed calculated by the ADAS
control unit
Warning sys-
tems ON indi-
cator Warning systems ON indicator signal Turns ON the warning systems ON indicator
Warning buzz-
er Warning buzzer signal Activates the warning buzzer
Revision: 2010 May2011 QX56

DAS
SYSTEM
DAS-411
< SYSTEM DESCRIPTION >[BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
FUNCTION DESCRIPTION
 The BSW system can help alert the driver of ot her vehicles in adjacent lanes when changing lanes.
 The BSW system uses side radar in stalled near the rear bumper to detect vehicles in an adjacent lane.
 The side radar can detect vehicles on either side of v ehicle within the detection zone shown as illustrated.
 This detection zone starts from the outside mirror of vehicle and extends approximately 10 ft (3.0 m) behind
the rear bumper, and approximately 10 ft (3.0 m) sideways.
 The BSW system operates above appr oximately 32 km/h (20 MPH).
 If the side radar detects vehicles in the detection zone, the BSW indicator illuminates.
 If the driver then activates the turn signal, a buzzer will sound twice and the BSW indicator will blink. NOTE:
A buzzer sounds if the side radar have already detected vehicles when the driver activates the turn signal. If
a vehicle comes into the detection zone after the driver activates the turn signal, then only the BSW indicator
blinks and no buzzer sounds.
BSW SYSTEM OPERATION DESCRIPTION
 ADAS control unit enables BSW system.
 The ADAS control unit turns on the BSW system w hen the warning systems switch is turned ON.
 Side radar detects a vehicle in the adjacent lane, and transmits the vehicle detection signal to ADAS control
unit via ITS communication.
 ADAS control unit starts the control as follows, bas ed on a vehicle detection signal, turn signal and dimmer
signal transmitted from BCM via CAN communication:
- BSW indicator signal and BSW indicator dimmer signal transmission to side radar.
- Buzzer signal transmission to warning buzzer.
 Side radar transmits an indicator operation signal to the BSW indicator according to BSW indicator signal
and BSW indicator dimmer signal.
Operation Condition of BSW System
ADAS control unit performs the control when the following conditions are satisfied.
 When the warning systems switch in turned ON.
 When the vehicle drives at approximately 32 km/h (20 MPH) or more to the forward direction.
JSOIA0257GB
JSOIA0258GB
Revision: 2010 May2011 QX56

DAS-412
< SYSTEM DESCRIPTION >[BSW]
SYSTEM
NOTE:
 After the operating conditions of warning are satisfi
ed, the warning continues until the vehicle speed reaches
approximately 29 km/h (18 MPH)
 The BSW system may not function properly, depending on the situation. Refer to DAS-417, "
Precautions for
Blind Spot Warning".
BULB CHECK ACTION AND FAIL-SAFE INDICATION
*: If BSW initial state is ON, warning systems ON indicator continues turned ON.
NOTE:
 The condition is seen regardless BSW system status (ON/OFF).
 If either of the side radars is in factor y-default mode, the BSW warning lamp blinks.
 New side radars are in factory-default mode.
Vehicle condition/Driver ′s operation BSW indicator Warning systems
ON indicator Indication on the combination meter
Ignition switch:
OFF ⇒ ON Approx. 2 sec. ON
Approx. 5 sec. ON
*
When DTC is detected OFF ON
Side radar is factory-default mode con-
dition
NOTEOFF — *1
When radar blockage is detected OFF ON
*2
JSOIA0374GB
JSOIA0254GB
JSOIA0255GB
JSOIA0255GB
Revision: 2010 May2011 QX56

DAS
SYSTEM
DAS-413
< SYSTEM DESCRIPTION >[BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
*1: Blinking cycle when the side radar is in factory-default mode condition
NOTE:
Time shown in the figure is approximate time.
*2: Blinking cycle when the side radar blockage condition
NOTE:
Time shown in the figure is approximate time.
BSW INITIAL STATE CHANGE
CAUTION:
Never change BSW initial state “ON” ⇒ “OFF” without the con sent of the customer.
BSW initial state can be changed.
 BSW initial ON* - BSW function is automatic ally turned ON, when the ignition switch OFF ⇒ ON.
 BSW initial OFF - BSW function is still OFF when the ignition switch OFF ⇒ ON.
*: Factory setting
How to change FCW/LDW/BSW initial state
1. Turn ignition switch ON.
2. Warning systems switch is OFF.
3. Push and hold warning systems switch for more than 4 seconds.
4. Buzzer sounds and blinking of the warning systems ON indicator informs that the FCW/LDW/BSW initial
state changes completed.
Fail-safe (ADAS Control Unit)INFOID:0000000006223852
If a malfunction occurs in each s ystem, ADAS control unit cancels eac h control, sounds a beep, and turns ON
the warning lamp or indicator lamp.
JSOIA0256GB
JSOIA0358GB
Revision: 2010 May2011 QX56

DAS-414
< SYSTEM DESCRIPTION >[BSW]
SYSTEM
Fail-safe (Side Radar)
INFOID:0000000006223853
FAIL-SAFE CONTROL BY DTC
If a malfunction occurs in the side radar, ADAS control unit cancels the control. Then the BSW warning lamp in
the combination meter illuminates.
TEMPORARY DISABLED STATUS AT BLOCKAGE
When the side radar is blocked, the operation is tempor arily cancelled. Then BSW warning lamp in combina-
tion meter blinks. Also, under the following conditions, the operation may be temporarily cancelled.
 The side radar may be blocked by temporary ambient c onditions such as splashing water, mist or fog.
 The blocked condition may also be caused by objects such as ice, frost or dirt obstructing the side radar.
System Buzzer Warning lamp/Indicator lamp Description
Vehicle-to-vehicle distance control mode High-pitched
toneICC system warn
ing lamp Cancel
Conventional (fixed speed) cruise control mode High-pitched
toneICC system warn
ing lamp Cancel
Intelligent Brake Assist (IBA) High-pitched
tone
IBA OFF indicator lamp Cancel
Forward Collision Warning (FCW) High-pitched
toneIBA OFF indicator lamp Cancel
Distance Control Assist (DCA) High-pitched
toneICC system warn
ing lamp Cancel
Lane Departure Warning (LDW) — Lane departure warning lamp Cancel
Lane Departure Prevention (LDP) Low-pitched
tone
Lane departure warning lamp Cancel
Blind Spot Warning (BSW) — BSW warning lamp Cancel
Revision: 2010 May2011 QX56

DAS
OPERATIONDAS-415
< SYSTEM DESCRIPTION > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
OPERATION
Switch Name and FunctionINFOID:0000000006223854
System Display and WarningINFOID:0000000006223855
INDICATOR AND WARNING LAMP
DISPLAY AND WARNING OPERATION
JSOIA0277ZZ
No. Name Function 1 Warning systems switch Turns BSW, LDW, and FCW systems ON/OFF
JSOIA0375ZZ
No. Name Description
1 Warning systems ON indicator  Turns ON while FCW/LDW/BSW system is ON
 Blinks when initial setting of FCW/LDW/BSW system changes
2 BSW warning lamp  Turns ON when BSW system is malfunctioning
 Blinks when the following conditions:
- Side radar is factory-default mode condition
- When radar blockage is detected
Vehicle condition/ Driver's operation Action
Warning
systems ON indicator Vehicle speed
(Approx.)
[km/h (MPH)] Turn signal
condition Status of ve-
hicle detec-
tion within detection area Indication on the
BSW indicator Buzzer
OFF — — — OFF OFF
Revision: 2010 May2011 QX56