sensor INFINITI QX56 2011 Factory Service Manual

TM-142
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P1734 7GR INCORRECT RATIO
P1734 7GR INCORRECT RATIO
DescriptionINFOID:0000000006226861
This malfunction is detected when the A/T does not shift
into 7GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or s horted) but by mechanical malfunction such as control
valve sticking, improper solenoid valve operation, etc.
DTC LogicINFOID:0000000006226862
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
“ TM-143, "
Diagnosis Procedure"” must be performed before star ting “DTC CONFIRMATION PROCE-
DURE”.
 Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.
 Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK ATF TEMPERATURE
With CONSULT-III
1. Start the engine.
2. Select “ATF TEMP 1” in “Data Monitor” in “TRANSMISSION”.
3. Check ATF temperature is in the following range.
With GST
1. Start the engine.
2. Drive vehicle for approximately 5 minutes in urban areas.
Is ATF temperature within specified range?
YES >> GO TO 3.
NO >> Drive vehicle to warm ATF or stop engine to cool ATF.
3.CHECK SYMPTOM (PART 1)
With CONSULT-III
1. Select “7TH GR FNCTN P1734” in “DTC & SRT confirmation” in “TRANSMISSION”.
2. Drive vehicle with manual mode and maintain the following conditions.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P1734 Gear 7 Incorrect Ratio The gear ratio is:
 0.821 or more
 0.729 or less Input clutch solenoid valve
 Direct clutch solenoid valve
 High and low reverse clutch
solenoid valve
 Front brake solenoid valve
 Low brake solenoid valve
 2346 brake solenoid valve
 Anti-interlock solenoid valve
 Each clutch and brake
 Output speed sensor
 Input speed sensor 1, 2
 Hydraulic control circuit
ATF TEMP 1 : 20 °C (68 °F) – 140 °C (284 °F)
Revision: 2010 May2011 QX56

SYSTEM SYMPTOMTM-165
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM DIAGNOSIS
SYSTEM SYMPTOM
Symptom TableINFOID:0000000006226890
 The diagnostics item numbers show the sequence for inspection. Inspect in order from item 1.
 Perform diagnoses of symptom table 1 before symptom table 2.
SYMPTOM TABLE 1
Symptom Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Poor
perfor-
mance
Driving
perfor-
manceShift point is high in “D” position. 1 2 3
Shift point is low in “D” position. 1 2
Large
shock
When
shifting
gears →
“D” position4 7665 32 31
→ “R” position 4 7 6 6 5 3 2 1
1GR ⇔ 2GR 4 2544 3 1
2GR ⇔ 3GR 4 2544 3 1
3GR ⇔ 4GR 4 2544 3 3 1
4GR ⇔ 5GR 4 2544 3 3 1
5GR ⇔ 6GR 4 2544 33 1
6GR ⇔ 7GR 4 2544 3 3 1
Downshift when
accelerator ped-
al is depressed 3 2433 1
Upshift when ac-
celerator pedal
is released 3 2433 1
Lock-up 4 2444 3 1
Judder Lock-up 2 1 1 4 3
Strange noise In “R” position 2 1
In “N” position 2 1
In “D” position 2 1
Engine at idle 2 1
Revision: 2010 May2011 QX56

TM-166
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
SymptomDiagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Func-
tion
trouble
Gear
does no
change “D” position Locks in 1GR 1 1 1 1
Locks in 2GR
Locks in 3GR
Locks in 4GR
Locks in 5GR 1
Locks in 6GR
Locks in 7GR
1GR
→ 2GR 1 1 1 1
2GR → 3GR 1
3GR → 4GR 2 22 2222 1
4GR → 5GR 1 1
5GR → 6GR 1
6GR → 7GR 1 1 1 1 1
5GR → 4GR 1
4GR → 3GR 1 1 1
3GR → 2GR 1 1
2GR → 1GR 1 1 1
Does not lock-up 2 22245 32222222 2 2 1
“M” posi-
tion 1GR
⇔ 2GR 3 33 32 3333333 3 3 1
2GR ⇔ 3GR 3 33 32 3333333 3 3 1
3GR ⇔ 4GR 3 33 32 3333333 3 3 1
4GR ⇔ 5GR 3 33 32 3333333 3 3 1
5GR ⇔ 6GR 3 33 32 3333333 3 3 1
6GR ⇔ 7GR 3 33 32 3333333 3 3 1
Revision: 2010 May2011 QX56

SYSTEM SYMPTOMTM-167
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Symptom Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter clutch solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Func-
tion trou-
ble
Poor
shiftingSlip
When
shifting
gears1GR
⇔ 2GR 3 3 3 4 2 2 1
2GR ⇔ 3GR 3 3 3 4 2 2 1
3GR ⇔ 4GR 3 3 3 4 2 2 2 2 1
4GR ⇔ 5GR 3 3 3 4 2 2 2 1
5GR ⇔ 6GR 3 3 3 4 2 2 2 1
6GR ⇔ 7GR 3 3 3 4 2 2 2 1
Engine
brake
does
not
work “D” position
→ “M” posi-
tion 5556423 33 1
“M” po-
sition 7GR
→ 6GR 5 5 5 6 4 2 3 3 3 1
6GR → 5GR 5 5 5 6 4 2 3 3 3 1
5GR → 4GR 5 5 5 6 4 2 3 3 3 1
4GR → 3GR 5 5 5 6 4 2 3 3 3 3 1
3GR → 2GR 5 556423 33 1
2GR → 1GR 5 5 5 6 4 2 3 3 3 1
Revision: 2010 May2011 QX56

TM-168
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
Func-
tion trou-
blePoor
power
trans-
mission
Slip With selector
lever in “D”
position, ac-
celeration is
extremely
poor.
53 334 2 2 2 1
With selector
lever in “R”
position, ac-
celeration is
extremely
poor. 53 334 2 2 2 1
While starting
off by acceler-
ating in 1GR,
engine races. 3 334 2 2 2 1
While acceler-
ating in 2GR,
engine races. 3 334 2 2 22 1
While acceler-
ating in 3GR,
engine races. 3 334 2 2 22 1
While acceler-
ating in 4GR,
engine races. 3 334 2 2 22 1
While acceler-
ating in 5GR,
engine races. 3 334 2 222 2 1
While acceler-
ating in 6GR,
engine races. 3 334 2 22221
While acceler-
ating in 7GR,
engine races. 3 334 2 2 22 2 1
Lock-up 3 334 2 2 1
No creep at
all. 111111111
Extremely
large creep. 1
Symptom
Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter clutch solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Revision: 2010 May2011 QX56

SYSTEM SYMPTOMTM-169
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM TABLE 2
Symptom Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter clutch solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Function
trouble
Power transmis-
sion cannot be
performed Vehicle cannot run in all
position.
3 2 111111111
Driving is not possible in
“D” position. 3 2 111111111
Driving is not possible in
“R” position. 32111
Engine stall 4 5 5 6 3 2 1
Engine stalls when selec-
tor lever shifted “N” → “D”
or “R”. 455 3 2 1
Engine does not start in
“N” or “P” position. 312 1
Engine starts in position
other than “N” or “P”. 32 1
Poor operation Vehicle does not enter
parking condition.
12
Parking condition is not
cancelled. 12
Vehicle runs with A/T in
“P” position. 12
Vehicle moves forward
with the “R” position. 12
Vehicle runs with A/T in
“N” position. 12
Vehicle moves backward
with the “D” position. 12
Revision: 2010 May2011 QX56

CONTROL CABLETM-179
< REMOVAL AND INSTALLATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
6. Remove retainer mounting bolts ( ) according to the following procedure.
a. Separate propeller shaft assembly (front). Refer to DLN-129,
"Removal and Installation". (For 4WD models)
b. Disconnect heated oxygen sensor 2 connectors (bank 1 and bank 2). Refer to EX-5, "
Exploded View".
c. Remove exhaust front tube (RH and LH). Refer to EX-5,
"Exploded View".
d. Remove heat plates above three way catalyst (RH and LH).
e. Remove control cable mounting bracket from A/T assembly.
f. Remove retainer mounting bolts from dash panel.
7. Remove control cable from the vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
When installing control cable (1) to A/T shift selector assembly (2),
check that control cable is fully pressed in with the ribbed (A) surface
facing upward.
Inspection and AdjustmentINFOID:0000000006226896
INSPECTION AFTER INSTALLATION
Check A/T position after adjusting A/T position. Refer to TM-101, "Inspection".
ADJUSTMENT AFTER INSTALLATION
Adjust A/T position. Refer to TM-101, "Adjustment".
JSDIA1677ZZ
JPDIA0609ZZ
Revision: 2010 May2011 QX56

CONTROL VALVE & TCMTM-183
< REMOVAL AND INSTALLATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
2. Remove clips (1).
3. Remove oil pan (2) and oil pan gasket.
4. Remove magnets (1) from oil pan.
5. Remove snap ring (1) from joint connector (2).
6. Push joint connector (1).
7. Disconnect output speed sensor connector (A). CAUTION:
Be careful not to damage connector.
8. Disengage terminal clip ( ).
: Vehicle front
: Oil pan mounting bolt
JSDIA1591ZZ
JPDIA0009ZZ
JSDIA1756ZZ
JSDIA1757ZZ
JPDIA1104ZZ
Revision: 2010 May2011 QX56

CONTROL VALVE & TCMTM-185
< REMOVAL AND INSTALLATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
CAUTION:
 Make sure that turbine revolution sensor securely installs input speed sensor holes (A).
 Hang down output speed senso r harness toward outside so
as not to disturb installation of the control valve & TCM.
 Adjust A/T assembly harness connector of the control valve
& TCM to terminal hole of transmission case.
 Assemble it so that manual valve (1) cutout is engaged with manual plate (2) projection.
- Install bolts and clip (1) to the control valve & TCM. Tighten bolt (E) to the specified torque before tightening the other than bolts.
*: Reamer bolt
 Refer to the following when installing oil pan to transmission case.CAUTION:
 Clean foreign materials (gear wear particles) that adhere on the inside of the oil pan and on the
magnet, and then assembly.
 Completely remove all moisture, oil and old gasket, etc. from oil pan gasket mounting surface of
transmission case and oil pan.
 Never reuse oil pan gasket and oil pan mounting bolts.
 Install oil pan gasket in the di rection to align hole position.
- Tighten the oil pan mounting bolts to the specified torque in the numerical order as shown in the figure after temporarily tightening
them.
JPDIA1106ZZ
JPDIA0012ZZ
: Vehicle front
Bolt symbol Length mm (in) Number of bolts A 43 (1.69) 3
B 40 (1.57) 2
C 54 (2.13) 6
D 50 (1.97) 2
E* 50 (1.97) 1
: Vehicle front
JPDIA1105ZZ
JSDIA1592GB
Revision: 2010 May2011 QX56

TM-186
< REMOVAL AND INSTALLATION >[7AT: RE7R01B]
CONTROL VALVE & TCM
Inspection and Adjustment
INFOID:0000000006226901
INSPECTION AFTER REMOVAL
Check foreign materials in oil pan to help determine causes of mal-
function. If the ATF is very dark, smells burned, or contains foreign
particles, the frictional material (clutches, band) may need replace-
ment. A tacky film that will not wipe clean indicates varnish build up.
Varnish can cause valves, servo, and clutches to stick and can
inhibit pump pressure.
 If frictional material is det ected, perform A/T fluid cooler
cleaning. Refer to TM-97, "
Cleaning".
INSPECTION AFTER INSTALLATION
Check A/T fluid leakage. Refer to TM-175, "Inspection".
ADJUSTMENT AFTER INSTALLATION
 Adjust A/T fluid level. Refer to TM-95, "Adjustment".
 Perform decel G sensor calibration when replacing control valve & TCM. Refer to TM-92, "
Special Repair
Requirement".
SCIA5199E
Revision: 2010 May2011 QX56