air condition INFINITI QX56 2011 Factory Service Manual

ENGINE COOLANTCO-9
< PERIODIC MAINTENANCE >
C
DE
F
G H
I
J
K L
M A
CO
NP
O
3. Check drained engine coolant for contaminants such as rust, corrosion or discoloration.
If contaminated, flush the engine cooling system. Refer to CO-10, "
Flushing".
RefillingINFOID:0000000006289659
1. Install reservoir tank if removed, and radiator drain plug.
CAUTION:
Be sure to clean drain plug and install with new O-ring. Refer to CO-13, "
Exploded View".
If water drain plug on cylinder block is removed, close and tighten it. Refer to EM-107, "
Disassem-
bly and Assembly".
2. Check that each hose clamp is firmly tightened.
3. Remove air relief plug (1) on heater hose.
4. Fill radiator, and reservoir tank, to specified level. Pour engine coolant through engine coolant filler neck
slowly of less than 3 (2-5/8 lmp qt) a minute to allow air
in system to escape.
 Use Genuine NISSAN Long Li fe Antifreeze/Coolant or
equivalent mixed with water (dis tilled or demineralized).
Refer to MA-10, "
Fluids and Lubricants".
5. When engine coolant overflows air relief hole on heater hos e, install air relief plug with clamp. Then refill
radiator with engine coolant.
6. Install radiator cap.
7. Install reservoir tank cap.
8. Warm up engine until opening thermostat less than 3,000 rpm.  Check thermostat opening condition by touching radiat or hose (lower) to see a flow of warm water.
CAUTION: : 1.96 N·m (0.2 kg-m, 17 in-lb)
2. Engine cover
: Vehicle front
JPBIA3429ZZ
Engine coolant capacity : Refer to CO-23,
"PeriodicalMaintenanceS
pecification".
(With reservoir tank at
“MAX” level)JPBIA0412ZZ
Reservoir tank engine
coolant capacity :Refer to
CO-23,
"PeriodicalMaintenanceSp
ecification".
(At “MAX” level)
A : MAX
B: MIN
JPBIA0102ZZ
Revision: 2010 May2011 QX56

DAS-5
C
DE
F
G H
I
J
K L
M B
DAS
N
P A
Description ..........................................................
..
208
Diagnosis Procedure .............................................208
NORMAL OPERATING CONDITION ...............210
Description .......................................................... ..210
REMOVAL AND INSTALLATION .............212
ICC SENSOR .................................................. ..212
Exploded View .................................................... ..212
Removal and Installation .......................................212
ACCELERATOR PEDAL ASSEMBLY ............213
Exploded View .................................................... ..213
DYNAMIC DRIVER ASSISTANCE SWITCH ...214
Exploded View .................................................... ..214
FCW
PRECAUTION ................ ............................
215
PRECAUTIONS .............................................. ..215
Precaution for FCW System Service ................... ..215
SYSTEM DESCRIPTION ...........................216
COMPONENT PARTS ................................... ..216
Component Parts Location .................................. ..216
Component Description .........................................216
SYSTEM ...........................................................218
System Description ............................................. ..218
Fail-safe (ADAS Control Unit) ...............................219
Fail-safe (ICC Sensor) ..........................................220
OPERATION .....................................................221
Switch Name and Function ................................. ..221
Menu Displayed by Pressing Each Switch ............221
HANDLING PRECAUTION ..............................223
Precautions for Forward Collision Warning ......... ..223
DIAGNOSIS SYSTEM (ADAS CONTROL
UNIT) ................................................................
224
On Board Diagnosis Function ............................. ..224
CONSULT-III Function (ICC/ADAS) ......................225
DIAGNOSIS SYSTEM (ICC SENSOR) ............235
CONSULT-III Function (LASER) ...........................235
ECU DIAGNOSIS INFO RMATION ............237
ADAS CONTROL UNIT .................................. ..237
Reference Value ................................................. ..237
Fail-safe ................................................................242
DTC Inspection Priority Chart ...............................243
DTC Index .............................................................244
ICC SENSOR ....................................................248
Reference Value ................................................. ..248
Fail-safe ................................................................249
DTC Inspection Priority Chart ...............................249
DTC Index ........................................................... ..249
WIRING DIAGRAM ....................................251
DRIVER ASSISTANCE SYSTEMS .................251
Wiring Diagram .................................................... ..251
BASIC INSPECTION .................................266
DIAGNOSIS AND REPAIR WORK FLOW .....266
Work Flow ............................................................ ..266
SYMPTOM DIAGNOSIS ............................268
FORWARD COLLISION WARNING SYSTEM
SYMPTOMS ....................................................
268
Symptom Table ................................................... ..268
FCW SYSTEM IS NOT ACTIVATED ..............269
Description .............................................................269
Diagnosis Procedure .............................................269
NORMAL OPERATING CONDITION .............270
Description .............................................................270
REMOVAL AND INSTALLATION .............271
WARNING SYSTEMS SWITCH ......................271
Removal and Installation ..................................... ..271
LDW & LDP
PRECAUTION ............... .............................
272
PRECAUTIONS ...............................................272
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ..
272
Precautions For Harness Repair ...........................272
Precaution for LDW/LDP System Service .............273
SYSTEM DESCRIPTION ...........................274
COMPONENT PARTS ....................................274
LANE DEPARTURE WARNING (LDW) SYSTEM ..274
LANE DEPARTURE WARNING (LDW) SYSTEM
: Component Parts Location ................................ ..
274
LANE DEPARTURE WARNING (LDW) SYSTEM
: Component Description .......................................
274
LANE DEPARTURE PREVENTION (LDP) SYS-
TEM ........................................................................ ..
275
LANE DEPARTURE PREVENTION (LDP) SYS-
TEM : Component Parts Location .........................
275
LANE DEPARTURE PREVENTION (LDP) SYS-
TEM : Component Description ..............................
276
SYSTEM ..........................................................277
LANE DEPARTURE WARNING (LDW) SYSTEM ..277
LANE DEPARTURE WARNING (LDW) SYSTEM
: System Description ............................................ ..
277
Revision: 2010 May2011 QX56

DAS-8
U1516 CAM CAN 3 ..........................................385
DTC Logic ............................................................ ..385
Diagnosis Procedure .............................................385
U1520 4WD CAN 3 ..........................................386
DTC Logic ............................................................ ..386
Diagnosis Procedure .............................................386
POWER SUPPLY AND GROUND CIRCUIT ...387
ADAS CONTROL UNIT ......................................... ..387
ADAS CONTROL UNIT : Diagnosis Procedure .....387
LANE CAMERA UNIT ............................................ ..387
LANE CAMERA UNIT : Diagnosis Procedure .......387
WARNING SYSTEMS SWITCH CIRCUIT .......389
Component Function Check ................................ ..389
Diagnosis Procedure .............................................389
Component Inspection ...........................................390
WARNING SYSTEMS ON INDICATOR CIR-
CUIT .................................................................
391
Component Function Check ................................ ..391
Diagnosis Procedure .............................................391
Component Inspection ...........................................392
WARNING BUZZER CIRCUIT .........................393
Component Function Check ................................ ..393
Diagnosis Procedure .............................................393
SYMPTOM DIAGNOSIS ............................395
LDW & LDP SYSTEM SYMPTOMS ............... .395
Symptom Table ................................................... ..395
LANE DEPARTURE WARNING LAMP DOES
NOT TURNED ON ...........................................
397
Description ........................................................... ..397
Diagnosis Procedure .............................................397
LDP ON INDICATOR LAMP DOES NOT
TURNED ON ....................................................
398
Description ........................................................... ..398
Diagnosis Procedure .............................................398
THE SYSTEM OPERATES EVEN WHEN US-
ING TURN SIGNAL .........................................
399
Description ........................................................... ..399
Diagnosis Procedure .............................................399
LDP SYSTEM SETTINGS CANNOT BE
TURNED ON/OFF ON THE NAVIGATION
SCREEN ..........................................................
400
Description ........................................................... ..400
Diagnosis Procedure .............................................400
NORMAL OPERATING CONDITION ..............401
Description ........................................................... ..401
REMOVAL AND INSTALLATION ..............403
LANE CAMERA UNIT .................................... ..403
Removal and Installation ...................................... .403
WARNING SYSTEMS SWITCH .......................404
Removal and Installation ...................................... .404
DYNAMIC DRIVER ASSISTANCE SWITCH ...405
Exploded View ..................................................... .405
WARNING BUZZER .........................................406
Removal and Installation ...................................... .406
BSW
PRECAUTION ............... ............................
407
PRECAUTIONS .............................................. ..407
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .............................................................. .
407
Precaution for BSW System Service ....................407
SYSTEM DESCRIPTION ..........................408
COMPONENT PARTS .................................... ..408
Component Parts Location .................................. .408
Component Description ........................................409
SYSTEM ...........................................................410
System Description .............................................. .410
Fail-safe (ADAS Control Unit) ...............................413
Fail-safe (Side Radar) ...........................................414
OPERATION .....................................................415
Switch Name and Function .................................. .415
System Display and Warning ................................415
HANDLING PRECAUTION ............................ ..417
Precautions for Blind Spot Warning ..................... .417
DIAGNOSIS SYSTEM (ADAS CONTROL
UNIT) .................................................................
418
On Board Diagnosis Function .............................. .418
CONSULT-III Function (ICC/ADAS) .....................419
DIAGNOSIS SYSTEM (SIDE RADAR LH) .......429
CONSULT-III Function (SIDE RADAR LEFT) ...... .429
DIAGNOSIS SYSTEM (SIDE RADAR RH) ......431
CONSULT-III Function (SIDE RADAR RIGHT) ... .431
ECU DIAGNOSIS INFORMATION ............433
ADAS CONTROL UNIT .................................. ..433
Reference Value .................................................. .433
Fail-safe ................................................................438
DTC Inspection Priority Chart ...............................439
DTC Index .............................................................440
SIDE RADAR LH ............................................ ..444
Reference Value .................................................. .444
Fail-safe ................................................................444
DTC Inspection Priority Chart ...............................445
Revision: 2010 May2011 QX56

DAS
C1A00 CONTROL UNITDAS-57
< DTC/CIRCUIT DIAGNOSIS > [ADAS CONTROL UNIT]
C
D
E
F
G H
I
J
K L
M B
N P A
DTC/CIRCUIT DIAGNOSIS
C1A00 CONTROL UNIT
DTC LogicINFOID:0000000006223481
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Perform “All DTC Readi ng” with CONSULT-III.
3. Check if the “C1A00” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A00” detected as the current malfunction?
YES >> Refer to DAS-57, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006223482
1.CHECK SELF-DIAGNOSIS RESULTS
Check if any DTC other than “C1A00” is detect ed in “Self Diagnostic Result” of “ICC/ADAS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
DAS-38, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis- play) Trouble diagnosis name DTC detecting condition Possible causes
C1A00 (0) CONTROL UNIT ADAS control unit inte
rnal malfunction ADAS control unit
Revision: 2010 May2011 QX56

DAS-58
< DTC/CIRCUIT DIAGNOSIS >[ADAS CONTROL UNIT]
C1A01 POWER SUPPLY CIRCUIT 1,
C1A02 POWER SUPPLY CIRCUIT 2
C1A01 POWER SUPPLY CIRCUIT 1, C1A02 POWER SUPPLY CIRCUIT 2
DTC LogicINFOID:0000000006223483
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the MAIN switch of ICC system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “C1A01” or “C1A02” is detected as t he current malfunction in “Self Diagnostic Result” of “ICC/
ADAS”.
Is
“C1A01” or “C1A02” detected as the current malfunction?
YES >> Refer to DAS-58, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006223484
1.CHECK ADAS CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT
Check power supply and ground circuit of ADAS control unit. Refer to DAS-62, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> Replace the ADAS control unit. Refer to DAS-63, "Removal and Installation".
NO >> Repair or replace the malfunctioning parts.
DTC
(On board dis-
play) Trouble diagnosis
name DTC detecting condition Possible causes
C1A01 (1) POWER SUPPLY
CIR The battery voltage sent to ADAS control unit re-
mains less than 7.9 V for 5 seconds
 Connector, harness, fuse
 ADAS control unit
C1A02
(2) POWER SUPPLY
CIR 2 The battery voltage sent to ADAS control unit re-
mains more than 19.3 V for 5 seconds
Revision: 2010 May2011 QX56

DAS
U1000 CAN COMM CIRCUITDAS-59
< DTC/CIRCUIT DIAGNOSIS > [ADAS CONTROL UNIT]
C
D
E
F
G H
I
J
K L
M B
N P A
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000006223485
CAN COMMUNICATION
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communicati on speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control units , and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN-H, CAN-L) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads the required data only.
CAN communication signal chart. Refer to LAN-28, "
CAN COMMUNICATION SYSTEM : CAN Communica-
tion Signal Chart".
ITS COMMUNICATION
 ITS communication is a multiplex communication syste m. This enables the system to transmit and receive
large quantities of data at high speed by connec ting control units with 2 communication lines.
 ITS communication lines adopt twisted-pair line st yle (two lines twisted) for noise immunity.
DTC LogicINFOID:0000000006223486
DTC DETECTION LOGIC
NOTE:
If “U1000” is detected, first diagnose the CAN communication system.
Diagnosis ProcedureINFOID:0000000006223487
1.PERFORM THE SELF-DIAGNOSIS
1. Turn the ignition switch ON.
2. Turn the MAIN switch of ICC system ON, and then wait for 30 seconds or more.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “U1000” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected as the current malfunction?
YES >> Refer to LAN-18, "Trouble Diagnosis Flow Chart".
NO >> Refer to GI-40, "
Intermittent Incident".
DTC
(On board display) Trouble diagnosis name DTC detecting condition Possible causes
U1000 (100) CAN COMM CIRCUIT If ADAS control unit is not transmitting or receiv-
ing CAN communication signal or ITS communi-
cation signal for 2 seconds or more  CAN communication system
 ITS communication system
Revision: 2010 May2011 QX56

DAS
U150F AV CAN 3DAS-61
< DTC/CIRCUIT DIAGNOSIS > [ADAS CONTROL UNIT]
C
D
E
F
G H
I
J
K L
M B
N P A
U150F AV CAN 3
DTC LogicINFOID:0000000006228052
DTC DETECTION LOGIC
NOTE:
If DTC “U150F” is detected along with DTC “U 1000”, first diagnose the DTC “U1000”. Refer to DAS-38, "
DTC
Index".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system or LDP system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “U150F” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U150F” detected as the current malfunction?
YES >> Refer to DAS-61, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228053
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U150F” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to DAS-59, "
DTC Logic".
NO >> GO TO 2.
2.CHECK AV CONTROL UNIT SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “S elf Diagnostic Result” of “MULTI AV”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
AV-57, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U150F (161) AV CAN CIRC 3 ADAS control unit detects an error signal that is
received from AV control unit via CAN commu-
nication
AV control unit
Revision: 2010 May2011 QX56

DAS-62
< DTC/CIRCUIT DIAGNOSIS >[ADAS CONTROL UNIT]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis ProcedureINFOID:0000000006223493
1.CHECK ADAS CONTROL UNIT POWER SUPPLY CIRCUIT
Check voltage between ADAS control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair the ADAS control unit power supply circuit.
2.CHECK ADAS CONTROL UNIT GROUND CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect the ADAS control unit connector.
3. Check for continuity between ADAS control unit harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair the ADAS control unit ground circuit.
Te r m i n a l Condition
Voltag e
(Approx.)
(+) (–)
ADAS control unit
GroundIgnition
switch
Connector Terminal
B61 16 OFF 0 V
ON Battery volt-
age
ADAS control unit
GroundContinuity
Connector Terminal
B61 6 Existed
Revision: 2010 May2011 QX56

DAS
PRECAUTIONSDAS-65
< PRECAUTION > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
 Bypass connection is never allowed at the repaired area. NOTE:
Bypass connection may cause ITS communication error. The
spliced wire becomes separated and t he characteristics of twisted
line are lost.
DCA System ServiceINFOID:0000000006223497
CAUTION:
 Never look straight into th e laser beam discharger when adjusting laser beam aiming.
 Turn the MAIN switch OFF in conditions similar to driving, such as free rollers or a chassis dyna-
mometer.
 Never use the ICC sensor removed from vehicle. Never disassemble or remodel.
 Erase DTC when replacing parts of DCA system, then check the operation of DCA system after
adjusting laser beam aiming if necessary.
SKIB8767E
Revision: 2010 May2011 QX56

DAS
C1A00 CONTROL UNITDAS-129
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
DTC/CIRCUIT DIAGNOSIS
C1A00 CONTROL UNIT
DTC LogicINFOID:0000000006223529
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Perform “All DTC Readi ng” with CONSULT-III.
3. Check if the “C1A00” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A00” detected as the current malfunction?
YES >> Refer to DAS-129, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006223530
1.CHECK SELF-DIAGNOSIS RESULTS
Check if any DTC other than “C1A00” is detect ed in “Self Diagnostic Result” of “ICC/ADAS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
DAS-38, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis- play) Trouble diagnosis name DTC detecting condition Possible causes
C1A00 (0) CONTROL UNIT ADAS control unit inte
rnal malfunction ADAS control unit
Revision: 2010 May2011 QX56