air condition INFINITI QX56 2011 Factory Service Manual

DAS-176
< DTC/CIRCUIT DIAGNOSIS >[DCA]
U0126 STRG SEN CAN 1
U0126 STRG SEN CAN 1
DTC LogicINFOID:0000000006228133
DTC DETECTION LOGIC
NOTE:
If DTC “U0126” is detected along with DTC “U
1000”, first diagnose the DTC “U1000”. Refer to DAS-182,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “U0126” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U0126” detected as the current malfunction?
YES >> Refer to DAS-176, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228134
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected ot her than “U0126” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communication system inspecti on. Repair or replace the malfunctioning parts.
Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U0126 (130) STRG SEN CAN CIR1 If ADAS control unit detects an error signal
that is received from steering angle sensor via
CAN communication
Steering angle sensor
Revision: 2010 May2011 QX56

DAS
U0235 ICC SENSOR CAN 1DAS-177
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
U0235 ICC SENSOR CAN 1
DTC LogicINFOID:0000000006228135
DTC DETECTION LOGIC
NOTE:
If DTC “U0235” is detected along with DTC “U 1000”, first diagnose the DTC “U1000”. Refer to DAS-182,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “U0235” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U0235” detected as the current malfunction?
YES >> Refer to DAS-177, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228136
1.CHECK ADAS CONTROL UNIT SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U0235” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ICC SENSOR SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “LASER”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
CCS-55, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U0235 (144) ICC SENSOR CAN
CIR1 If ADAS control unit detects an error signal
that is received from ICC sensor via ITS com-
munication
ICC sensor
Revision: 2010 May2011 QX56

DAS-178
< DTC/CIRCUIT DIAGNOSIS >[DCA]
U0401 ECM CAN 1
U0401 ECM CAN 1
DTC LogicINFOID:0000000006228137
DTC DETECTION LOGIC
NOTE:
If DTC “U0401” is detected along with DTC “U
1000”, first diagnose the DTC “U1000”. Refer to DAS-182,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “U0401” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U0401” detected as the current malfunction?
YES >> Refer to DAS-178, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228138
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected ot her than “U0401” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communication system inspecti on. Repair or replace the malfunctioning parts.
Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ECM SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “S elf Diagnostic Result” of “ENGINE”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
EC-98, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board
display) Trouble diagnosis name DTC detecting condition Possible causes
U0401 (120) ECM CAN CIR1 If ADAS control unit detects an error signal
that is received from ECM via CAN communi-
cation
ECM
Revision: 2010 May2011 QX56

DAS
U0402 TCM CAN 1DAS-179
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
U0402 TCM CAN 1
DTC LogicINFOID:0000000006228139
DTC DETECTION LOGIC
NOTE:
If DTC “U0402” is detected along with DTC “U 1000”, first diagnose the DTC “U1000”. Refer to DAS-182,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “U0402” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U0402” detected as the current malfunction?
YES >> Refer to DAS-179, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228140
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U0402” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK TCM SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Sel f Diagnostic Result” of “TRANSMISSION”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
TM-78, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis
name DTC detecting condition Possible causes
U0402 (122) TCM CAN CIRC1 If ADAS control unit detects an error signal
that is received from TCM via CAN communi-
cation
TCM
Revision: 2010 May2011 QX56

DAS-180
< DTC/CIRCUIT DIAGNOSIS >[DCA]
U0415 VDC CAN 1
U0415 VDC CAN 1
DTC LogicINFOID:0000000006228141
DTC DETECTION LOGIC
NOTE:
If DTC “U0415” is detected along with DTC “U
1000”, first diagnose the DTC “U1000”. Refer to DAS-182,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “U0415” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U0415” detected as the current malfunction?
YES >> Refer to DAS-180, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228142
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected ot her than “U0415” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communication system inspecti on. Repair or replace the malfunctioning parts.
Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U0415 (126) VDC CAN CIR1 If ADAS control unit de
tects an error signal
that is received from ABS actuator and electric
unit (control unit) via CAN communication ABS actuator and electric unit (control
unit)
Revision: 2010 May2011 QX56

DAS
U0428 STRG SEN CAN 2DAS-181
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
U0428 STRG SEN CAN 2
DTC LogicINFOID:0000000006228143
DTC DETECTION LOGIC
NOTE:
If DTC “U0428” is detected along with DTC “U 1000”, first diagnose the DTC “U1000”. Refer to DAS-182,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “U0428” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U0428” detected as the current malfunction?
YES >> Refer to DAS-181, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228144
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U0428” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (C ONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U0428 (131) STRG SEN CAN CIR2 If ADAS control unit detects an error signal
that is received from steering angle sensor via
CAN communication
Steering angle sensor
Revision: 2010 May2011 QX56

DAS-182
< DTC/CIRCUIT DIAGNOSIS >[DCA]
U1000 CAN COMM CIRCUIT
U1000 CAN COMM CIRCUIT
ADAS CONTROL UNIT
ADAS CONTROL UNIT : DescriptionINFOID:0000000006228145
CAN COMMUNICATION
CAN (Controller Area Network) is a serial communication
line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control units , and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN-H, CAN-L) allowing a hi gh rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads the required data only.
CAN communication signal chart. Refer to LAN-28, "
CAN COMMUNICATION SYSTEM : CAN Communica-
tion Signal Chart".
ITS COMMUNICATION
 ITS communication is a multiplex communication system . This enables the system to transmit and receive
large quantities of data at high speed by connecting control units with 2 communication lines.
 ITS communication lines adopt twisted-pair line st yle (two lines twisted) for noise immunity.
ADAS CONTROL UNIT : DTC LogicINFOID:0000000006228146
DTC DETECTION LOGIC
NOTE:
If “U1000” is detected, first diagnose the CAN communication system.
ADAS CONTROL UNIT : Diagnosis ProcedureINFOID:0000000006228147
1.PERFORM THE SELF-DIAGNOSIS
1. Turn the ignition switch ON.
2. Turn the DCA system ON, and then wait for 30 seconds or more.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “U1000” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected as the current malfunction?
YES >> Refer to LAN-18, "Trouble Diagnosis Flow Chart".
NO >> Refer to GI-40, "
Intermittent Incident".
ACCELERATOR PEDAL ACTUATOR
ACCELERATOR PEDAL ACTUATOR : DescriptionINFOID:0000000006223619
ITS COMMUNICATION
 ITS communication is a multiplex communication system . This enables the system to transmit and receive
large quantities of data at high speed by connecting control units with 2 communication lines
 ITS communication lines adopt twisted-pair line st yle (two lines twisted) for noise immunity.
ACCELERATOR PEDAL ACTUATOR : DTC LogicINFOID:0000000006223620
DTC DETECTION LOGIC
DTC
(On board
display) Trouble diagnosis name DTC detecting condition Possible causes
U1000 (100) CAN COMM CIRCUIT If ADAS control unit is not transmitting or receiv-
ing CAN communication signal or ITS communi-
cation signal for 2 seconds or more  CAN communication system
 ITS communication system
Revision: 2010 May2011 QX56

DAS
U150B ECM CAN 3DAS-185
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
U150B ECM CAN 3
DTC LogicINFOID:0000000006228151
DTC DETECTION LOGIC
NOTE:
If DTC “U150B” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to DAS-182,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “U150B” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U150B” detected as the current malfunction?
YES >> Refer to DAS-185, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228152
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U150B” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ECM SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “S elf Diagnostic Result” of “ENGINE”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
EC-98, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U150B (157) ECM CAN CIRC 3
ADAS control unit detects an error signal that is
received from ECM via CAN communication ECM
Revision: 2010 May2011 QX56

DAS-186
< DTC/CIRCUIT DIAGNOSIS >[DCA]
U150C VDC CAN 3
U150C VDC CAN 3
DTC LogicINFOID:0000000006228153
DTC DETECTION LOGIC
NOTE:
If DTC “U150C” is detected along with DTC “U
1000”, first diagnose the DTC “U1000”. Refer to DAS-182,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “U150C” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U150C” detected as the current malfunction?
YES >> Refer to DAS-186, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228154
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected ot her than “U150C” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communication system inspecti on. Repair or replace the malfunctioning parts.
Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U150C (158) VDC CAN CIRC 3 ADAS control unit detects an error signal that is
received from ABS actuat
or and electric unit
(control unit) via CAN communication ABS actuator and electric unit (control
unit)
Revision: 2010 May2011 QX56

DAS
U150D TCM CAN 3DAS-187
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
U150D TCM CAN 3
DTC LogicINFOID:0000000006228155
DTC DETECTION LOGIC
NOTE:
If DTC “U150D” is detected along with DTC “U1000 ”, first diagnose the DTC “U1000”. Refer to DAS-182,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “U150D” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U150D” detected as the current malfunction?
YES >> Refer to DAS-187, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228156
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U150D ” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK TCM SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Sel f Diagnostic Result” of “TRANSMISSION”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
TM-78, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U150D (159) TCM CAN CIRC 3
ADAS control unit detects an error signal that is
received from TCM via CAN communication TCM
Revision: 2010 May2011 QX56