fuse INFINITI QX56 2011 Factory Owner's Manual

BRC-98
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
C1143 STEERING ANGLE SENSOR
3. Disconnect fuse block (J/B) harness connector.
4. Check continuity between steering angle sensor
harness connector and fuse block (J/B) harness connec-
tor.
5. Check continuity between steering angle sensor harness connector and ground.
Is the inspection result normal?
YES >> Perform trouble diagnosis for ignition power supply. Refer to PG-89, "Wiring Diagram - IGNITION
POWER SUPPLY -".
NO >> Repair or replace error-detected parts.
4.CHECK STEERING ANGL E SENSOR GROUND CIRCUIT
1. Turn the ignition switch OFF.
2. Check continuity between steering angle sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace error-detected parts.
5.CHECK TERMINAL
 Check steering angle sensor pin terminals for damage or loose connection with harness connector.
 Check fuse block (J/B) pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace error-detected parts.
6.CHECK CAN COMMUNICATION LINE
Check “STRG BRANCH LINE CIRCUIT”. Refer to LAN-81, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-137, "Removal and Installa-
tion".
NO >> Repair or replace error-detected parts. Refer to BRC-7, "
Precaution for Harness Repair".
Steering angle sensor Fuse block (J/B)
Continuity
Connector Terminal Connector Terminal
M30 4 M1 2A Existed
Steering angle sensor —Continuity
Connector Terminal
M30 4 Ground Not existed
Steering angle sensor —Continuity
Connector Terminal
M30 1 Ground Existed
Revision: 2010 May2011 QX56

BRC-100
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
C1145, C1146 YAW RATE/SIDE/DECEL G SENSOR
C1145, C1146 YAW RATE/SIDE/DECEL G SENSOR
DTC LogicINFOID:0000000006222623
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK DTC DETECTION
With CONSULT-III.
1. Turn the ignition switch OFF to ON.
2. Perform self-diagnosis for “ABS”.
Is DTC
“C1145” or “C1146” detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-100, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006222624
CAUTION:
 A malfunction in yaw rate/side/ decel G sensor system may be det ected when the vehicle sharply
turns during a spin turn, acceleratio n turn or drift driving while VDC function is OFF (VDC OFF indi-
cator lamp is in ON status). This is not a malfun ction if the status returns to normal after engine is
started again. In that case, erase self-diagn osis result memory using CONSULT-III.
 When the engine is in running stat us and the vehicle is on a turntable at the entrance of parking lot
or on a moving unit, VDC warning lamp may tu rn ON and “ABS” self-diagnosis may display “YAW
RATE SENSOR”. In this case, yaw rate sensor is not malfunctioning. The status returns to normal
when the vehicle is left from the turntable or movi ng unit and the engine is started again. In that
case, erase self-diagnosis result memory using CONSULT-III.
1.CHECK YAW RATE/SIDE/DECEL G SENSOR MOUNTING CONDITION
Check yaw rate/side/decel G sensor mounting condition. Refer to BRC-138, "
Exploded View".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.CHECK YAW RATE/SIDE/DECE L G SENSOR POWER SUPPLY
1. Turn the ignition switch OFF.
2. Disconnect yaw rate/side/decel G sensor harness connector.
3. Check voltage between yaw rate/side/dec el G sensor harness connector and ground.
4. Turn the ignition switch ON. CAUTION:
Never start engine.
5. Check voltage between yaw rate/side/dec el G sensor harness connector and ground.
DTC Display Item Malfunction detected condition Possible causes
C1145 YAW RATE SENSOR  When a malfunction is detected in yaw rate signal.
 When yaw rate signal is not continuously received
for 2 seconds or more.
 When side G signal is not continuously received for 2 seconds or more.
 When decel G signal is not continuously received for 2 seconds or more.  Harness or connector
 Yaw rate/side/decel G sensor
 ABS actuator and electric unit
(control unit)
 Ignition power supply system
Fuse
C1146 SIDE G-SEN CIRCUIT When a malfunction is detected in side/decel G sig-
nal.
Yaw rate/side/decel G sensor
—Voltage
Connector Terminal
M55 3 Ground Approx. 0 V
Revision: 2010 May2011 QX56

C1145, C1146 YAW RATE/SIDE/DECEL G SENSOR
BRC-101
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 3.
3.CHECK YAW RATE/SIDE/DECEL G SENSOR POWER SUPPLY CIRCUIT
1. Turn the ignition switch OFF.
2. Check 10A fuse (#57).
3. Disconnect IPDM E/R harness connector.
4. Check continuity between yaw rate/side/decel G sensor harness connector and IPDM E/R harness con-
nector.
5. Check continuity between yaw rate/side/decel G sensor harness connector and ground.
Is the inspection result normal?
YES >> Perform trouble diagnosis for ignition power supply. Refer to PG-89, "Wiring Diagram - IGNITION
POWER SUPPLY -".
NO >> Repair or replace error-detected parts.
4.CHECK YAW RATE/SIDE/DECEL G SENSOR GROUND CIRCUIT
1. Turn the ignition switch OFF.
2. Check continuity between yaw rate/side/decel G sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace error-detected parts.
5.CHECK COMMUNICATION LINE (1)
1. Disconnect ABS actuator and electric unit (control unit) harness connector.
2. Check continuity between yaw rate/side/decel G sensor harness connector and ABS actuator and electric
unit (control unit) harness connector.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace error-detected parts.
Yaw rate/side/decel G sensor —Voltage
Connector Terminal
M55 3 Ground Battery voltage
Yaw rate/side/decel G sensor IPDM E/R Continuity
Connector Terminal Connector Terminal
M55 3 E15 59 Existed
Yaw rate/side/decel G sensor —Continuity
Connector Terminal
M55 3 Ground Not existed
Yaw rate/side/decel G sensor —Continuity
Connector Terminal
M55 6 Ground Existed
Yaw rate/side/decel G sens or ABS actuator and electric unit (control unit)
Continuity
Connector Terminal Connector Terminal
M55 4
E36 9
Existed
510
Revision: 2010 May2011 QX56

POWER SUPPLY AND GROUND CIRCUITBRC-113
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
POWER SUPPLY AND GROUND CIRCUIT
DescriptionINFOID:0000000006222641
ABS actuator and electric uni t (control unit) power supply
Diagnosis ProcedureINFOID:0000000006222642
1.CHECK ABS ACTUATOR AND ELECTRIC UNIT (C ONTROL UNIT) IGNITION POWER SUPPLY (1)
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
3. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
4. Turn the ignition switch ON CAUTION:
Never start engine.
5. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CON TROL UNIT) IGNITION POWER SUPPLY CIRCUIT
(1)
1. Turn the ignition switch OFF.
2. Check 10A fuse (#57).
3. Disconnect IPDM E/R harness connector.
4. Check continuity between ABS actuator and electr ic unit (control unit) harness connector and IPDM E/R
harness connector.
5. Check for continuity between ABS actuator and el ectric unit (control unit) harness connector and the
ground.
Is the inspection result normal?
YES >> Perform trouble diagnosis for ignition power supply. Refer to PG-89, "Wiring Diagram - IGNITION
POWER SUPPLY -".
NO >> Repair or replace error-detected parts.
3.CHECK ABS ACTUATOR AND ELECTRIC UNIT (C ONTROL UNIT) IGNITION POWER SUPPLY (2)
1. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
ABS actuator and electric unit (control unit)
—Voltage
Connector Terminal
E36 18 Ground Approx. 0 V
ABS actuator and electric unit (control unit) —Voltage
Connector Terminal
E36 18 Ground 10 − 16 V
ABS actuator and electric unit (control unit) IPDM E/R
Continuity
Connector Terminal Connector Terminal
E3618E1559Existed
ABS actuator and electric unit (control unit) —Continuity
Connector Terminal
E36 18 Ground Not existed
Revision: 2010 May2011 QX56

BRC-114
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
POWER SUPPLY AND GROUND CIRCUIT
2. Turn the ignition switch ON
CAUTION:
Never start engine.
3. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 4.
4.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CON TROL UNIT) IGNITION POWER SUPPLY CIRCUIT
(2)
1. Turn the ignition switch OFF.
2. Check 10A fuse (#74).
3. Check continuity and short circui t between ABS actuator and electric unit (control unit) harness connector
terminal (49) and 10A fuse (#74).
Is the inspection result normal?
YES >> Perform trouble diagnosis for ignition power supply. Refer to PG-89, "Wiring Diagram - IGNITION
POWER SUPPLY -".
NO >> Repair or replace error-detected parts.
5.CHECK MOTOR AND MOTOR RE LAY POWER SUPPLY CIRCUIT
1. Turn the ignition switch OFF.
2. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
3. Turn the ignition switch ON. CAUTION:
Never start engine.
4. Check voltage between ABS actuator and electr ic unit (control unit) harness connector and ground.
Is the inspection result normal?
YES >> GO TO 7.
NO >> GO TO 6.
6.CHECK MOTOR AND MOTOR RE LAY POWER SUPPLY CIRCUIT
1. Turn the ignition switch OFF.
2. Check 50A fusible link (M).
3. Check continuity and short circui t between ABS actuator and electric unit (control unit) harness connector
terminal (4 and 47) and 50A fusible link (M).
ABS actuator and electric unit (control unit) —Voltage
Connector Terminal
E37 49 Ground Approx. 0 V
ABS actuator and electric unit (control unit) —Voltage
Connector Terminal
E37 49 Ground 10 − 16 V
ABS actuator and electric unit (control unit)
—Voltage
Connector Terminal
E36 4 Ground Battery voltage
E37 47
ABS actuator and electric unit (control unit)
—Voltage
Connector Terminal
E36 4 Ground Battery voltage
E37 47
Revision: 2010 May2011 QX56

CCS
C1A01 POWER SUPPLY CIRCUIT 1, C1A02 POWER SUPPLY CIRCUIT 2
CCS-85
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
C1A01 POWER SUPPLY CIRCUIT 1, C1A02 POWER SUPPLY CIRCUIT 2
ADAS CONTROL UNIT
ADAS CONTROL UNIT : DTC LogicINFOID:0000000006227992
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the MAIN switch of ICC system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “C1A01” or “C1A02” is detected as t he current malfunction in “Self Diagnostic Result” of “ICC/
ADAS”.
Is
“C1A01” or “C1A02” detected as the current malfunction?
YES >> Refer to CCS-85, "ADAS CONTROL UNIT : Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
ADAS CONTROL UNIT : Diagnosis ProcedureINFOID:0000000006227993
1.CHECK ADAS CONTROL UNIT PO WER SUPPLY AND GROUND CIRCUIT
Check power supply and ground circuit of ADAS control unit. Refer to DAS-62, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> Replace the ADAS control unit. Refer to DAS-63, "Removal and Installation".
NO >> Repair or replace the malfunctioning parts.
ICC SENSOR
ICC SENSOR : DTC LogicINFOID:0000000006224306
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the MAIN switch of ICC system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “C1A01” or “C1A02” is detected as the current malfunction in “Self Diagnostic Result” of
“LASER”.
Is
“C1A01” or “C1A02” detected as the current malfunction?
YES >> Refer to CCS-86, "ICC SENSOR : Diagnosis Procedure".
DTC
(On board dis- play) Trouble diagnosis
name DTC detecting condition Possible causes
C1A01 (1) POWER SUPPLY
CIR The battery voltage sent to ADAS control unit re-
mains less than 7.9 V for 5 seconds
 Connector, harness, fuse
 ADAS control unit
C1A02
(2) POWER SUPPLY
CIR 2 The battery voltage sent to ADAS control unit re-
mains more than 19.3 V for 5 seconds
DTC
Trouble diagnosis
name DTC detecting condition Possible causes
C1A01 POWER SUPPLY
CIR The battery voltage sent to ICC sensor remains
less than 7.9 V for 5 seconds
 Connector, harness, fuse
 ICC sensor
C1A02 POWER SUPPLY
CIR 2 The battery voltage sent to ICC sensor remains
more than 19.3 V for 5 seconds
Revision: 2010 May2011 QX56

CCS
C1A2A ICC SENSOR POWER SUPPLY CIRCUITCCS-117
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
C1A2A ICC SENSOR POWER SUPPLY CIRCUIT
DTC LogicINFOID:0000000006224351
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the MAIN switch of ICC system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “C1A2A” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A2A” detected as the current malfunction?
YES >> Refer to CCS-117, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006224352
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “C1A2A ” in “Self Diagnostic Result” of “ICC/ADAS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
CCS-145, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ICC SENSOR SELF-DIAGNOSIS
Check if any DTC is detected in “Self Diagnostic Result” of “LASER”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
CCS-55, "
DTC Index".
NO >> Replace ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board display) Trouble diagnosis name DTC detecting condition Possible cause
C1A2A (80) ICC SEN PWR SUP CIR Abnormal powe
r supply voltage in ICC sensor Harness, connector, fuse
 ICC sensor
Revision: 2010 May2011 QX56

CCS
C1F05 ACCELERATOR PEDAL ACTUATOR POWER SUPPLY CIRCUIT
CCS-131
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
C1F05 ACCELERATOR PEDAL ACTU ATOR POWER SUPPLY CIRCUIT
DTC LogicINFOID:0000000006224378
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “C1F05” is detected as the current malfunction on the self-diagnosis results of “ICC/ADAS”.
Is
“C1F05” detected as the current malfunction?
YES >> Refer to CCS-131, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006224379
1.CHECK ADAS CONTROL UNIT SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “C1F05” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to CCS-145, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ACCELERATOR PEDAL ACTU ATOR SELF-DIAGNOSIS RESULTS
Check if “C1F05” is detected in “Self Diagnostic Result” of “ACCELE PEDAL ACT”.
Is
“C1F05” detected?
YES >> Refer to DAS-171, "ACCELERATOR PEDAL ACTUATOR : DTC Logic".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board
display) Trouble diagnosis name DTC detecting condition Possible causes
C1F05 (95) APA PWR SUPLY CIR The battery voltage sent to accelerator pedal
actuator remains less than 7.9 V or more than
19.3 V for 5 seconds  Harness, connector, or fuse
 Accelerator pedal actuator
Revision: 2010 May2011 QX56

CHG-16
< BASIC INSPECTION >
CHARGING SYSTEM PRELIMINARY INSPECTION
CHARGING SYSTEM PRELIMINARY INSPECTION
Inspection ProcedureINFOID:0000000006274866
1.CHECK BATTERY TERMINALS CONNECTION
Check if battery terminals are clean and tight.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair battery terminals connection.
2.CHECK FUSE
Check for blown fuse and fusible link.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace the blown fuse after repairing the applicable circuit.
3.CHECK “E” TERMINAL CONNECTION
Check if “E” terminal (alternator ground harness) is clean and tight.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair “E” terminal connection.
4.CHECK DRIVE BELT TENSION
Check drive belt tension. Refer to EM-20, "
Checking".
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair as needed.
Unit Power source (Power supply terminals) Fuse No.
Alternator Battery (“S” terminal) 32
Combination meter Ignition switch ON (“L” terminal) 3
Revision: 2010 May2011 QX56

CHG-20
< DTC/CIRCUIT DIAGNOSIS >
L TERMINAL CIRCUIT (OPEN)
L TERMINAL CIRCUIT (OPEN)
DescriptionINFOID:0000000006274870
The “L” terminal circuit controls the charge warning lamp. The charge warning lamp illuminates when the igni-
tion switch is set to ON or START. When the alternat or is providing sufficient voltage with the engine running,
the charge warning lamp will go off. If the charge warn ing lamp illuminates with the engine running, a malfunc-
tion is indicated.
Diagnosis ProcedureINFOID:0000000006274871
1.CHECK “L” TERMINAL CONNECTION
1. Turn ignition switch OFF.
2. Check that “L” terminal is clean and tight.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair “L” terminal connection. Confirm repair by performing complete Starting/Charging system test. Refer to Technical Service Bulletin.
2.CHECK “L” TERMIN AL CIRCUIT (OPEN)
1. Disconnect alternator connector.
2. Apply ground to alternator harness connector terminal.
3. Check condition of the charge warning lamp with the ignition switch in the ON position.
Does it illuminate?
YES >> “L” terminal circuit is normal. Refer to CHG-13, "Work Flow".
NO >> GO TO 3.
3.CHECK HARNESS CONTI NUITY (OPEN CIRCUIT)
1. Disconnect the battery cable from the negative terminal.
2. Disconnect the combination meter connector.
3. Check continuity between alternator harness connector and combination meter harness connector.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair the harness or connector.
4.CHECK HARNESS CONTI NUITY (OPEN CIRCUIT)
Check continuity between combination me ter harness connector and fuse block (J/B).
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair the harness or connector.
5.CHECK POWER SUPPLY CIRCUIT
(+) (–) Condition Charge warning lamp
Alternator
Connector Terminal E205 3 Ground Ignition switch ON ON
Alternator Combination meter Continuity
Connector Terminal Connector Terminal
E205 3 M34 25 Existed
Combination meter Fuse block (J/B) Continuity
Connector Terminal Connector Terminal
M34 2 M1 2A Existed
Revision: 2010 May2011 QX56