rear panel INFINITI QX56 2011 Factory Workshop Manual

BODY SIDE TRIMINT-21
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
Apply protective tape (B) to the body panel to protect from damage.
2. Remove rear side bracket.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
 Visually check the pawls and metal clips for defo rmation and damage during installation. Replace
with new ones if necessary.
 When installing front ki cking plate inner and rear kicking plat e inner, check that pawls and metal
clips are securely fitted in body panel holes, and press them in.
KICKING PLATE OUTER
KICKING PLATE OUTER : Removal and InstallationINFOID:0000000006220250
CAUTION:
 When removing, always use a remover tool that is made of plastic.
 Never damage the body.
REMOVAL
Front kicking plate outer
Disengage front kicking plate outer fixing pawls using a remover tool
(A) as shown by the arrow in the figure, and then remove front kick-
ing plate outer (1).
CAUTION:
Apply protective tape (B) to the body panel to protect from dam-
age.
Rear kicking plate outer
Disengage rear kicking plate outer fixing pawls using a remover tool
(A) as shown by the arrow in the figure, and then remove rear kick-
ing plate outer (1).
CAUTION:
Apply protective tape (B) to the body panel to protect from dam-
age.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
: Pawl
JMJIA4023ZZ
: Pawl
JMJIA4022ZZ
: Pawl
JMJIA4024ZZ
Revision: 2010 May2011 QX56

INT-22
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
CAUTION:
 Visually check the pawls for deformation and damage during installation. Replace with new ones if
necessary.
 When installing front kicking pl ate outer and rear kicking plate outer, check that pawls are securely
fitted in body panel ho les, and press them in.
CENTER PILLAR LOWER GARNISH
CENTER PILLAR LOWER GARNISH : Removal and InstallationINFOID:0000000006220251
CAUTION:
Never damage the body.
REMOVAL
1. Remove front kicking plate inner and rear kicking plate inner. Refer to INT-20, "KICKING PLATE INNER :
Removal and Installation".
2. Slide front seat assembly to the frontmost position.
3. Remove seat belt outer anchor. Refer to SB-6, "
SEAT BELT RETRACTOR : Removal and Installation".
4. Disengage center pillar lower garnish fixing clips.
5. Remove center pillar lower garnish according to the order of the arrows shown in the figure.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
 Visually check the clips for deformation and dama ge during installation. Replace with new ones if
necessary.
 When installing center pillar lowe r garnish, check that clips are secu rely fitted in body panel holes,
and press them in.
CENTER PILLAR UPPER GARNISH
CENTER PILLAR UPPER GARNISH : Removal and InstallationINFOID:0000000006220252
CAUTION:
 When removing, always use a remover tool that is made of plastic.
 Never damage the body.
REMOVAL
1. Remove front kicking plate inner and rear kicking plate inner. Refer to INT-20, "KICKING PLATE INNER :
Removal and Installation".
2. Slide front seat assembly to the frontmost position.
3. Remove center pillar lower garnish. Refer to INT-22, "
CENTER PILLAR LOWER GARNISH : Removal
and Installation".
: Clip
JMJIA4025ZZ
Revision: 2010 May2011 QX56

FLOOR TRIMINT-25
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
FOR SECOND CAPTAIN SEAT
FRONT FLOOR CARPET
FRONT FLOOR CARPET : Re moval and InstallationINFOID:0000000006220254
REMOVAL
1. Remove front seat assembly (driver and passenger). Refer to SE-112, "Removal and Installation".
2. Remove second seat assembly (LH and RH). Refer to SE-125, "
Removal and Installation".
3. Remove floor grille (LH and RH). Refer to VTL-12, "
REAR FLOOR GRILLE : Removal and Installation".
4. Remove front kicking plate inner and rear kicking plate inner (LH and RH). Refer to INT-20, "
KICKING
PLATE INNER : Removal and Installation".
5. Remove dash side finisher (LH and RH). Refer to INT-18, "
DASH SIDE FINISHER : Removal and Installa-
tion".
6. Remove center pillar lower garnish (LH and RH). Refer to INT-22, "
CENTER PILLAR LOWER GARNISH :
Removal and Installation".
7. Remove instrument lower panel LH. Refer to IP-14, "
Removal and Installation".
8. Remove center console assembly. Refer to IP-25, "
Removal and Installation".
9. Remove adjusting nut and front cable mounting bolts and nuts, and then remove front cable. Refer to TM-
176, "Removal and Installation".
JMJIA4008ZZ
1. Front floor carpet 2. Carpet hook 3. Fixing clip
4. Footrest 5. Front floor spacer front 6. Front floor spacer rear
7. Floor hook 8. Rear floor carpet 9. Dual lock fastener
: Pawl
: Vehicle front
Revision: 2010 May2011 QX56

INT-30
< REMOVAL AND INSTALLATION >
HEADLINING
6. Disconnect harness connectors. Lane camera unit harness connector (1) (if equipped).
 Inside mirror harness connector (2).
 Light & rain sensor harness connector / rain sensor harness
connector (3).
7. Remove assist grips  Insert a small flat-bladed screwdriver (A) into the gap between
assist grip cap (1), and then remove assist grip cap.
 Remove assist grip mounting bolts, and then remove assist grips (2).
8. Insert a remover tool (A) between luggage room lamp (1) and roof garnish to disengage the fixing metal clips, and then discon-
nect luggage room lamp harness connector.
CAUTION:
Apply protective tape (B) to the roof garnish to protect from
damage.
9. Insert a remover tool (A) between roof garnish (1) and body panel to disengage the fixing clips and pawls, and then remove
roof garnish.
10. Remove front pillar garnish (LH and RH). Refer to INT-19, "
FRONT PILLAR GARNISH : Removal and
Installation".
11. Remove front kicking plate inner (LH and RH) and rear kicking plate inner (LH and RH). Refer to INT-20,
"KICKING PLATE INNER : Removal and Installation".
12. Remove dash side finisher (LH and RH). Refer to INT-18, "
DASH SIDE FINISHER : Removal and Installa-
tion".
13. Remove center pillar lower garnish (LH and RH). Refer to INT-22, "
CENTER PILLAR LOWER GARNISH :
Removal and Installation".
JMJIA4054ZZ
JMJIA4063ZZ
: Metal clip
JMLIA1059ZZ
: Clip
: Pawl
JMJIA4066ZZ
Revision: 2010 May2011 QX56

HEADLININGINT-31
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
14. Remove luggage side lower finisher (LH and RH). Refer to INT-36, "LUGGAGE SIDE LOWER FINISHER
: Removal and Installation".
15. Remove front body side welt (LH and RH) and rear body side welt (LH and RH). Refer to INT-20, "
BODY
SIDE WELT : Removal and Installation".
16. Remove center pillar upper garnish (LH and RH). Refer to INT-22, "
CENTER PILLAR UPPER GARNISH :
Removal and Installation".
17. Remove rear pillar finisher (LH and RH). Refer to INT-37, "
REAR PILLAR FINISHER : Removal and
Installation".
18. Remove back pillar garnish (LH and RH). Refer to INT-37, "
BACK PILLAR GARNISH : Removal and
Installation".
19. Remove luggage side upper finisher (LH and RH). Refer to INT-38, "
LUGGAGE SIDE UPPER FINISHER
: Removal and Installation".
20. Insert a remover tool between map lamp assembly (1) and headlining assembly to disengage the fixing metal clips, and
then remove map lamp assembly.
21. Peel off dual lock fastener between headlining assembly and roof panel.
22. Remove headlining clips located at the rear side
23. Remove headlining assembly (1) through the back door.
CAUTION:
 When removing, 2 workers are required.
 Never bend headlini ng when removing.
 Be careful not to scratch or damage any part of the body while taking out the headlining.
24. Remove the following parts after removing headlining assembly.
: Metal clip
JMJIA4062ZZ
JMJIA4068ZZ
Revision: 2010 May2011 QX56

LUGGAGE FLOOR TRIMINT-35
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
3. Disengage luggage floor board RH (1) fixing pawls and clips, and then remove luggage side finisher.
4. Disengage luggage floor board LH (2) fixing pawls and clips,
and then remove luggage side finisher.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
 Visually check the clips and pawls for deformation and damage during installation. Replace with new
ones if necessary.
 When installing luggage floor rear board, check that clips and pawls are securely fitted in body panel
holes, and press them in.
LUGGAGE REAR PLATE
LUGGAGE REAR PLATE : Removal and InstallationINFOID:0000000006220260
REMOVAL
1. Open luggage floor board center.
2. Remove luggage floor finishers (LH and RH).
1. Remove nuts shown by the arrows in the figure.
2. Disengage luggage floor finisher (1) fixing clip and pawl
using a remover tool (A), and then remove luggage side fin-
isher.
3. Disengage luggage rear plate (1) fixing clips and pawls using a remover tool (A), and then remove luggage rear plate.
4. Remove luggage rear plate mask from luggage rear plate.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
 Visually check the clips and pawls for deformation and damage during installation. Replace with new
ones if necessary.
 When installing luggage rear plate, check that cl ips and pawls are securely fitted in body panel
holes, and press them in.
: Clip
: Pawl
JMJIA4030ZZ
: Clip
: Pawl
JMJIA4028ZZ
: Clip
: Pawl
JMJIA4041ZZ
Revision: 2010 May2011 QX56

LUGGAGE FLOOR TRIMINT-37
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
 Visually check the clips and pawls for deformation and damage during installation. Replace with new
ones if necessary.
 When installing luggage side lo wer finisher, check that clips and pawls are securely fitted in body
panel holes, and press them in.
REAR PILLAR FINISHER
REAR PILLAR FINISHER : Removal and InstallationINFOID:0000000006220262
REMOVAL
1. Remove luggage side lower finisher. INT-36, "LUGGAGE SIDE LOWER FINISHER : Removal and Instal-
lation".
2. Disengage lower side of rear pillar finisher fixing clip.
3. Pull rear pillar upper garnish (1) from inside passenger room, disengage rear pillar upper garnish upper side fixing pawl as shown in the following figure, and then remove rear pillar upper garnish from body
panel (2).
CAUTION:
Be careful not to apply excessive force when removing rear pillar finisher. Otherwise, pawl may be
damaged and fragments may drop in body panel holes on body.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
 Replace rear pillar finisher wi th a new part after removal. Never reuse rear pillar finisher.
 Visually check the clip and pawl for deformation an d damage during installation. Replace with new
ones if necessary.
 When installing rear pillar finisher, check that cl ip and pawl are securely fitted in body panel holes,
and press them in.
BACK PILLAR GARNISH
BACK PILLAR GARNISH : Removal and InstallationINFOID:0000000006220263
REMOVAL
1. Remove luggage side lower finisher. INT-36, "LUGGAGE SIDE LOWER FINISHER : Removal and Instal-
lation".
2. Remove cap of back door finisher side (LH), and then remove stud ball. Refer to DLK-247, "
BACK DOOR
SUPPORT ROD : Removal and Installation" (LH side only).
3. Disengage back pillar garnish (1) fixing clips and pawl using a remover tool (A), and then remove back pillar garnish.
JMJIA1176ZZ
: Clip
: Pawl
JMJIA4045ZZ
Revision: 2010 May2011 QX56

INT-38
< REMOVAL AND INSTALLATION >
LUGGAGE FLOOR TRIM
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
 Visually check the clips and pawl for deformation and damage during installation. Replace with new
ones if necessary.
 When installing back pillar garnis h, check that clips and pawl are securely fitted in body panel holes,
and press them in.
LUGGAGE SIDE UPPER FINISHER
LUGGAGE SIDE UPPER FINISHER : Removal and InstallationINFOID:0000000006220264
REMOVAL
1. Remove luggage side lower finisher. Refer to INT-36, "LUGGAGE SIDE LOWER FINISHER : Removal
and Installation".
2. Remove rear pillar finisher. Refer to INT-37, "
REAR PILLAR FINISHER : Removal and Installation".
3. Remove back pillar garnish. Refer to INT-37, "
BACK PILLAR GARNISH : Removal and Installation".
4. Remove luggage side upper finisher. 1. Remove mounting bolts (1).
2. Disengage luggage side upper finisher (2) fixing clips usinga remover tool (A), and then remove luggage side upper fin-
isher (3).
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
 Visually check the clips for deformation and dama ge during installation. Replace with new ones if
necessary.
 When installing luggage side uppe r finisher, check that clips are securely fitted in body panel holes,
and press them in.
: Clip
JMJIA4046ZZ
Revision: 2010 May2011 QX56

IP-1
BODY INTERIOR
C
DE
F
G H
I
K L
M
SECTION IP
A
B
IP
N
O P
CONTENTS
INSTRUMENT PANEL
PRECAUTION ................ ...............................2
PRECAUTIONS .............................................. .....2
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
2
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect .....................................
2
Service ......................................................................3
PREPARATION ............................................4
PREPARATION .............................................. .....4
Special Service Tools ........................................ ......4
Commercial Service Tools .......................................4
CLIP LIST ............................................................6
Clip List ............................................................... ......6
SYMPTOM DIAGNOSIS ...............................7
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES ...............................................................
7
Work Flow ............................................................ .....7
Inspection Procedure ................................................9
Diagnostic Worksheet ..............................................11
REMOVAL AND INSTALLATION ...............13
INSTRUMENT PANEL ASSEMBLY .................13
Exploded View ..................................................... ....13
Removal and Installation .........................................14
CENTER CONSOLE ASSEMBLY ....................23
Exploded View .........................................................23
Removal and Installation .........................................25
Disassembly and Assembly .....................................27
REAR CONSOLE ASSEMBLY .........................29
Exploded View .........................................................29
Removal and Installation .........................................29
Disassembly and Assembly .....................................30
Revision: 2010 May2011 QX56

IP-14
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
Removal and Installation
INFOID:0000000006113098
WORK STEP
When removing instrument panel assembly, combination meter, front display unit, AV control unit, instrument
finisher A, instrument fini sher B, and center console assembly take st eps as per the order shown in the follow-
ing chart.
1. Optical sensor 2. Front defroster grille RH 3. Front defroster grille LH
4. Speaker grille LH 5. Squawker LH 6. Instrument finisher A
7. Combination meter 8. Cluster lid A 9. Push-button ignition switch
10. Illumination lamp 11. Socket and bulb 12. Instrument lower panel LH
13. Steering column upper cover 14. Steering column lower cover 15. Fuse block lid
16. Instrument center finisher LH 17. Instrument center finisher RH 18. Instrument lower cover
19. Illumination lamp 20. Socket and bulb 21. Glove box assembly
22. Socket and bulb 23. Illumination lamp 24. Instrument finisher B
25. Front passenger air bag module 26. Instrument panel assembly 27. Squawker RH
28. Speaker grille RH 29. Sunload sensor 30. Upper ventilator grille
31. Center speaker 32. Front display unit 33. AV control unit
34. Cluster lid D 35. Cluster lid C 36. Cluster lid C lower
37. Inner socket 38. Socket knob
: Clip
: Pawl
: Metal clip
Refer to GI-4, "
Components" for symbols in the figure.
PA R T S INSTRU-
MENT
PA N E L
ASSEMBLY COMBINA-
TION
METER FRONT
DISPLAY
UNIT AV c o n t r o l
unit INSTRU-
MENT
FINISHER A INSTRU-
MENT
FINISHER B CENTER
CONSOLE
ASSEMBLY
Instrument lower cover [1] [1] [1] [1] [1]
Glove box assembly [2] [2]
Front passenger air bag module
harness connector [3] [3]
Front passenger air bag module
mounting bolt [4] [4]
Selector lever knob [5] [2] [2] [5] [2]
Console finisher assembly [6] [3] [3] [6] [3]
Instrument center finisher RH [7] [4] [4] [7] [4]
Front body side welt RH [8] [8]
Front pillar garnish RH [9] [9]
Speaker grille RH [10] [10]
Squawker RH [11] [11]
Front defroster grille RH [12] [12]
Front defroster grille LH [13] [13]
Instrument center finisher LH [14] [5] [5] [14] [5]
Console rear finisher [15] [15] [6]
Center console assembly [16] [16] [7]
Front body side welt LH [17] [1] [1] [17]
Front pillar garnish LH [18] [18]
Speaker grille LH [19] [19]
Revision: 2010 May2011 QX56