rear panel INFINITI QX56 2011 Factory Owner's Manual

FENDER PROTECTOREXT-23
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
FENDER PROTECTOR
FENDER PROTECTOR
FENDER PROTECTOR : Exploded ViewINFOID:0000000006367605
FENDER PROTECTOR
FENDER PROTECTOR : Remo val and InstallationINFOID:0000000006367606
REMOVAL
1. Remove mounting bolts, from front lower.
2. Release front fender protector fixing clips, and then remove front fender protector.
3. Disengage hoodledge insulator fixing pawls, and then remove hoodledge insulator.
INSTALLATION
Install in the reverse order of removal.
REAR WHEEL HOUSE PROTECTOR
1. Fender protector 2. U nut 3. Over fender
4. Fender 5. Hoodledge insurator 6. Fender clip
A: To hoodledge panel
JMKIA5463ZZ
Revision: 2010 May2011 QX56

EXT-32
< REMOVAL AND INSTALLATION >
DOOR OUTSIDE MOLDING
DOOR OUTSIDE MOLDING
Exploded ViewINFOID:0000000006367617
Removal and InstallationINFOID:0000000006367618
FRONT DOOR OUTSIDE MOLDING
Removal
1. Fully open door window.
1. Front door panel 2. Front door outside molding 3. Rear door outside molding
4. Rear door panel: Pawl
JMKIA5372ZZ
Revision: 2010 May2011 QX56

DOOR OUTSIDE MOLDINGEXT-33
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
2. Twist and pull up to upper side, and then remove front door out- side molding (1).
CAUTION:
 Apply protective tape around front door panel.
 Never twist and pull up to do or outside molding strongly.
REAR DOOR OUTSIDE MOLDING
1. Fully open door window.
2. Twist and pull up to upper side, and then remove rear door out-
side molding (1).
CAUTION:
 Apply protective tape around rear door panel.
 Never twist and pull up to do or outside molding strongly.
Installation
Install in the reverse order of removal.
JMKIA2024ZZ
JMKIA2026ZZ
Revision: 2010 May2011 QX56

EXT-36
< REMOVAL AND INSTALLATION >
SILL MOLDING
SILL MOLDING
Exploded ViewINFOID:0000000006367621
Removal and InstallationINFOID:0000000006367622
REMOVAL
1. Fully open front and rear door.
2. Disengage sill molding (1) fixing clips with a remover tool (A),and then remove sill molding.
CAUTION:
 Disengage the clips slowly and carefully.
 Never pull the sill molding strongly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
 When installing, check visually th e sill molding and the clips, then replace them with new parts if
they have been damaged.
 When installing the sill molding, check that blind clips are secure ly fitted in panel holes on body, and
then press them in.
1. Sill molding 2. Double-sided tape
[t: 1.2 mm (0.047) in]
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA5380ZZ
: Clip
JMKIA2029ZZ
Revision: 2010 May2011 QX56

EXT-38
< REMOVAL AND INSTALLATION >
DOOR SASH COVER
2. Insert a remover tool (A) between front door sash cover (1) anddoor panel, cut double-sided tape using a cutter (B) while lifting
front door sash cover, and remove front door sash cover.
CAUTION:
 Use a remover tool which is made of a material that doesnot damage door panel.
 Never lift front door sash cover with excessive force.
Installation
Note the following items, and then install in the reverse order of removal.
CAUTION:
 When installing, slid e and install front door sash cover (2)
from door rear side, so that front door outside molding (1) is
not deformed.
 Replace double-sided tape on back of front door sash cover with a new double-sided adhesive tape
if front door sash cover is reused.
 Replace EPT sealer of front door sash cover with a new EPT sealer if front door sash cover is
reused.
 Remove double-sided adhesive ta pe remaining on body and back of front door sash cover using
double-sided adhesive tape remover wh en removing front door sash molding.
 Install after cleaning adhesive parts of doo r side and back of front door sash cover.
 To secure contact, do not wash vehicle within 24 hours after installation.
REAR DOOR SASH COVER
Removal
1. Remove rear door sash cover fixing clips.
2. Insert a remover tool (A) between rear door sash cover (1) and
door panel, cut double-sided tape using a cutter (B) while lifting
rear door sash cover, and remove rear door sash cover.
CAUTION:
 Never use an item as a remover tool that could damagedoor panel.
 Never lift rear door sash cover with excessive force.
Installation
Note the following items, and install in the reverse order of removal.
CAUTION:
JMKIA2034ZZ
JMKIA5005ZZ
JMKIA2034ZZ
Revision: 2010 May2011 QX56

REAR SPOILEREXT-41
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
REAR SPOILER
Exploded ViewINFOID:0000000006367627
Removal and InstallationINFOID:0000000006367628
REMOVAL
1. Remove back door trim. Refer to INT-39, "Removal and Installation".
2. Remove rear spoiler mounting nuts.
3. Cut rear spoiler fixing double-sided tape with cutter knife.
4. Disengage rear spoiler fixing clips with remover tool (A), and then remove rear spoiler.
CAUTION:
Apply a protective tape (B) on body panel and rear spoiler
to protect the painted surface from damage.
1. Rear spoiler assembly 2. Grommet 3. High-mounted stop lamp
4. High-mounted stop lamp cover 5. Washer nozzle 6. EPT sealer [t: 5.0 mm (0.197 in)]
7. Double-sided tape
[t: 1.6 mm (0.063 in)] 8. EPT sealer [t: 4.0 mm (0.157 in)]
: Clip
: Vehicle front
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA5322ZZ
: Clip
JMKIA5383ZZ
Revision: 2010 May2011 QX56

EXT-42
< REMOVAL AND INSTALLATION >
REAR SPOILER
5. Remove following parts after removing rear spoiler. High-mounted stop lamp
Grommets
 Washer nozzle
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
 Be careful no to damage the back door.
 Always replace double-sided tape with a new one, if rear spoiler is reused.
 Remove double-sided tape remain ing on back door panel and back of rear spoiler with a double-
sided tape remover, after removing rear spoiler.
 When installing, visually check the rear spoiler and the clips, then replace them with new parts if
they are damaged.
 When installing rear spoiler, check that clips an d bolts are securely fitted in back door panel holes,
and then press them in.
 Never wash the vehicle within 24 hours af ter installing so as to keep adhesive.
Revision: 2010 May2011 QX56

DRIP MOLDINGEXT-43
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
DRIP MOLDING
Exploded ViewINFOID:0000000006367629
Removal and InstallationINFOID:0000000006367630
REMOVAL
Remove drip molding fixing clips from rear end to front end using
remover tool (A).
CAUTION:
Apply protective tape (B) on body panel to protect the painted
damage from damage.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
When installing, check visually the drip molding and clips, then replace them with new parts if they are
damaged.
1. Drip molding clip 2. Drip molding
JMKIA5314ZZ
: Clip
JMKIA5474ZZ
Revision: 2010 May2011 QX56

GW-14
< REMOVAL AND INSTALLATION >
SIDE WINDOW GLASS
SIDE WINDOW GLASS
Exploded ViewINFOID:0000000006220816
1. Side window glass 2. Body side outer panel 3. Luggage side upper finisher
4. Adhesive 5. Primer 6. Back pillar garnish
7. Rear pillar finisher 8. Luggage side lower finisher
JMKIA5206GB
Revision: 2010 May2011 QX56

GW-16
< REMOVAL AND INSTALLATION >
BACK DOOR WINDOW GLASS
BACK DOOR WINDOW GLASS
Exploded ViewINFOID:0000000006220819
Removal and InstallationINFOID:0000000006220820
REMOVAL
1. Remove rear spoiler. Refer to EXT-41, "Removal and Installation".
2. Remove the connectors and grounds for the back door window defogger.
1. Dam-sealant rubber upper 2. Back door window glass 3. Back door window glass holder (up- per)
4. Back door window glass molding 5. Back door window glass holder (low- er)6. Back door panel outer
7. Back door panel inner 8. Adhesive 9. Primer : Do not reuse
Unit : mm (in)
JMKIA5457GB
Revision: 2010 May2011 QX56