wheel INFINITI QX56 2011 Factory Manual PDF

BRM-14
< PREPARATION >
BODY COMPONENT PARTS
NOTE:
 For the parts without a number described in the figure, it is supplied only with the assembly part that the part is included with.
 Tensile strength column shows the largest strength value of a part in the component part.
CAUTION:
If the high strength steel (ultra high strength steel) of this is broken, replace by assembly for the supply part. No. Parts name
Tensile strength
(MPa) Both sided anti-corrosive
precoated steel sections
1. Frame assembly Refer to No.2−36
2. Front bumper crossmember assembly T=1.8 mm
(0.071 in)
980
caution—
3. 2nd crossmember assembly 440 —
4. 2nd crossmember reinforcement (RH & LH) 440 —
5. 1st cab mounting bracket (RH & LH) Under 440 —
6. Front side member assembly (RH & LH) 540 —
7. Front suspension bracket assembly (RH & LH) Under 440 —
8. Engine mounting bracket assembly (RH & LH) Under 440 —
9. 2nd cab mounting bracket assembly (RH & LH) Under 440 —
10. 3way connector bracket assembly (RH & LH) Under 440 —
11. Piping bracket assembly (RH & LH) Under 440 —
12. Front bound bumper bracket assembly (RH & LH) 540 —
13. Lower front link mounting bracket assembly (RH & LH) 440 —
14. Diagonal member complete (RH & LH) 540 —
15. Rear engine mounting gusset assembly Under 440 —
16. Rear engine mounting member complete Under 440 —
17. Front fuel tank protector (RH & LH) Under 440 —
18. 3rd cab mounting bracket assembly (RH & LH) Under 440 —
19. Center side member assembly (RH & LH) 540 —
20. 6th crossmember assembly Under 440 —
21. Exhaust bracket (Front) Under 440 —
22. Fuel tank protector (RH & LH Rear) Under 440 —
23. Heat insulator bracket Under 440 —
24. Fuel tank protector assembly (RH & LH) 540 —
25. Rear suspension mounting bracket assembly (RH & LH) 540 —
26. 4th cab body mounting bracket assembly (RH & LH) Under 440 —
27. Rear brake hose bracket (RH & LH) Under 440 —
28. Rear shock absorber bracket assembly (RH & LH) 540 —
29. Rear side member assembly (RH & LH) 540 —
30. 5th cab body bracket (RH & LH) Under 440 —
31. 7th crossmember assembly Under 440 —
32. Exhaust bracket (Rear) Under 440 —
33. Spare wheel crossmember assembly Under 440 —
34. Front under cover bracket assembly Under 440 —
35. Rear end gusset (RH & LH) 440 —
36. Rear end crossmember assembly 540 —
Revision: 2010 May2011 QX56

BRM-16
< REMOVAL AND INSTALLATION >
CORROSION PROTECTION
Undercoating
INFOID:0000000006248492
The underside of the floor and wheelhouse are undercoated to prevent rust, vibration, noise and stone chip-
ping. Therefore, when such a panel is replaced or re paired, apply undercoating to that part. Use an undercoat-
ing which is rust resistant, soundproof, vibr ation-proof, shock-resistant, adhesive, and durable.
Precautions in Undercoating
1. Never apply undercoating to any place unless specif ied (such as the areas above the muffler and three
way catalyst that are subjected to heat).
2. Never undercoat the exhaust pipe or other parts that become hot.
3. Never undercoat rotating parts.
4. Apply bitumen wax after applying undercoating.
5. After putting seal on the vehicle, put undercoating on it.
B. Nozzle insert hole
Unit: mm (in)
: Anti-corrosive wax coated portions
JSKIA1888GB
Revision: 2010 May2011 QX56

BODY CONSTRUCTIONBRM-23
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
BRM
N
O P
10. Lower dash reinforcement 11. Lower dash 12. Lower hinge plate (Front)
13. Lower front pillar hinge brace 14. Front floor 15. 2nd body mounting member
16. 2nd body mounting bracket 17. Inner sill 18. Center sill reinforcement
19. Outer sill reinforcement 20. Side member outrigger 21. Inner center pillar
22. Inner center pillar reinforcement 23. Upper outer center pillar reinforce- ment24. Center pillar hinge brace
25. Center pillar plate 26. Lower hinge plate (Rear) 27. Lower center pillar bracket
28. 3rd body mounting bracket 29. Rear floor front 30. Outer sill rear reinforcement
31. Anchor plate 32. Outer rear wheelhouse 33. Sill closing plate
34. Inner rear pillar 35. Inner side panel reinforcement 36. Roof rail rear brace
37. Inner back pillar 38. Inner rear roof side rail 39. Back pillar reinforcement
40. Upper back pillar main 41. Back pillar seat belt anchor
Revision: 2010 May2011 QX56

CCS-10
< SYSTEM DESCRIPTION >[ICC]
COMPONENT PARTS
Component Description
INFOID:0000000006224266
× : Applicable
13. Steering angle sensor
Refer to BRC-10, "
Component Parts
Location"
14. ADAS control unit
Refer to DAS-13, "
Component Parts
Location"
A. Back side of engine room (RH) B. Front bumper (center) C. Upper side of brake pedal
D. Under side of inst rument lower driver
panel
Component Function
Description
Vehicle-to-vehicle distance control mode
Conventional (fixed speed) cruise control mode Intelligent Brake Assist (IBA)
Brake Assist (with preview function)
ADAS control unit ×××× ADAS control unit calculates a target distance between vehicles
and a target speed, based on signals received from each sensor
and switch to transmit an engine torque command value to ECM
and a brake fluid pres sure control signal to ABS actuator and
electric unit (control unit) via CAN communication
 ADAS control unit transmits buzzer output signal to combination
meter via CAN communication
ICC sensor ×××× ICC sensor detects light reflected from a vehicle ahead by irra-
diating laser forward and calculates a distance from the vehicle
ahead and a relative speed, based on the detected signal
 ICC sensor transmits the presence/absence of vehicle ahead and the distance from the vehicle to ADAS control unit via ITS
communication
ECM ×××× ECM transmits the accelerator pedal position signal, ICC brake
switch signal, stop lamp switch signal, ICC steering switch sig-
nal, etc. to ADAS control unit via CAN communication
 ECM controls the electric throttle control actuator based on the engine torque demand received from the ADAS control unit via
CAN communication
ABS actuator and electric unit
(control unit) ×××× ABS actuator and electric unit (control unit) transmits the vehicle
speed signal (wheel speed), stop lamp signal and VDC/TCS/
ABS system operation condition to ADAS control unit via CAN
communication
 ABS actuator and electric unit (control unit) controls the brake, based on a brake fluid pressure control signal received from the
ADAS control unit via CAN communication
BCM ×BCM transmits the front wiper request signal to ADAS control unit
via CAN communication
TCM ××TCM transmits the signal related to A/T control to ADAS control
unit via CAN communication
Revision: 2010 May2011 QX56

CCS
COMPONENT PARTSCCS-11
< SYSTEM DESCRIPTION > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
NOTE:
Only IBA system uses
Combination meter ××××Performs the following operations using the signals received from
the ADAS control unit via the CAN communication
 Displays the ICC system operation status using the meter dis-
play signal
 Illuminates the ICC system warning lamp using the ICC warning
lamp signal
 Illuminates the IBA OFF indicator lamp using the IBA OFF indi- cator lamp signal
 Operates the buzzer (ICC warning chime) using the buzzer out- put signal
ICC steering switch ×× ICC steering switch allows the ON/OFF of the Intelligent Cruise
Control and the settings of a vehicle speed and distance be-
tween vehicles
 ICC steering switch signal is transmitted to ECM. ECM transmits the signal to the ADAS control unit via CAN communication
ICC brake switch ×××× ICC brake switch is turned OFF and stop lamp switch is turned
ON, when depressing the brake pedal
 ICC brake switch signal is input to ECM. These signals are transmitted from ECM to ADAS control unit via CAN communi-
cation
 Stop lamp switch signal is in put to ECM and ABS actuator and
electric unit (control unit). These signals are transmitted from
ECM and ABS actuator and electric unit (control unit) to ADAS
control unit via CAN communication
Stop lamp switch
××××
ICC brake hold relay ××ICC brake hold relay activates the stop lamp by ICC brake hold re-
lay drive signal (stop lamp drive signal) outputted by the ADAS
control unit
Transfer control unit ××××Transfer control unit transmits a mode selection state of 4WD shift
switch to the ADAS control unit via CAN communication
IBA OFF switch ×
NoteIBA OFF switch signal is input to the ADAS control unit
Steering angle sensor ×Measures the rotation amount, rotation speed, and rotation direc-
tion of steering wheel, and then transmits them to ADAS control
unit via CAN communication
Component
Function
Description
Vehicle-to-vehicle distance control mode
Conventional (fixed speed) cruise control mode Intelligent Brake Assist (IBA)
Brake Assist (with preview function)
Revision: 2010 May2011 QX56

CCS
SYSTEMCCS-13
< SYSTEM DESCRIPTION > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
Transmit unit Signal name Description
ECM CAN com-
munica-
tionClosed throttle position signal Receives idle position state (ON/OFF)
Accelerator pedal position signal Receives accelerator pedal position (angle)
ICC prohibition signal
Receives an operable/inoperable state of the ICC sys-
tem
ICC steering switch
signal Main switch signal
Receives the operational state of the ICC steering
switch
SET/COAST switch
signal
CANCEL switch sig-
nal
RESUME/ACCEL-
ERATE switch signal
DISTANCE switch
signal
Engine speed signal Receives engine speed
Stop lamp switch signal Receives an operational state of the brake pedal
ICC brake switch signal Receives an operational state of the brake pedal
Snow mode signal Receives an operational state of the snow mode
TCM CAN com-
munica-
tionInput speed signal Receives the number of revolutions of input shaft
Current gear position signal Receives a current gear position
Shift position signal Receives a selector lever position
Output shaft revolution signal Receives the number of revolutions of output shaft
ABS actuator
and electric unit
(control unit) CAN com-
munica-
tionABS malfunction signal Receives
a malfunction state of ABS
ABS operation signal Receives an operational state of ABS
ABS warning lamp signal Receives an ON/OFF state of ABS warning lamp
TCS malfunction signal Receives a malfunction state of TCS
TCS operation signal Receives an operational state of TCS
VDC OFF switch signal Receives an ON/OFF state of VDC
VDC malfunction signal Receives a malfunction state of VDC
VDC operation signal Receives an operational state of VDC
Vehicle speed signal (ABS) Receives wheel speeds of four wheels
Stop lamp switch signal Receives an operational state of the brake pedal
Yaw rate signal Receives yaw rate acting on the vehicle
Combination
meter CAN com-
munica-
tion
Parking brake switch signal Receives an operational state of the parking brake
BCM CAN com-
munica-
tion
Front wiper request signal Receives an operational state of front wiper(s)
Steering angle
sensor CAN com-
munica-
tionSteering angle sensor malfunction signal Receives a malfunction state of steering angle sensor
Steering angle sensor signal
Receives the number of revolutions, turning direction of
the steering wheel
Steering angle speed signal Receives the turning angle speed of the steering wheel
Transfer control
unit CAN com-
munica-
tion
Current 4WD mode signal Receives a mode selection state of the 4WD mode
Revision: 2010 May2011 QX56

CCS-18
< SYSTEM DESCRIPTION >[ICC]
SYSTEM
 When the SET/COAST switch is pushed under the following condi-
tions, the system cannot be set. A warning chime will sound and
the set speed indicator and own vehicle indicator will blink.
- When the SNOW mode switch is ON (To use the ICC system, turn
OFF the SNOW mode switch, push the MAIN switch to turn OFF
the ICC system and reset the ICC system by pushing the MAIN
switch again.)
- When the 4WD shift switch is not AUTO position. (To use the ICC
system, shift the AUTO position, push the MAIN switch to turn OFF
the ICC system and reset the ICC system by pushing the MAIN
switch again.)
- When the VDC is OFF. (To use the ICC system, turn ON the VDC system, push the MAIN switch to turn OFF the I CC system and reset the ICC system by pushing the MAIN
switch again.)
- When ABS or VDC (including the TCS) operates.
- When driving into a strong light (i.e., sunlight).
- When the wheel is slipping. (To use the ICC system, make sure the wheels are no longer spinning, push the
MAIN switch to turn OFF the ICC system and rese t the ICC system by pushing the MAIN switch again.)
Cancel Conditions
1. When CANCEL switch is pressed.
2. When brake pedal is depressed.
3. When the vehicle ahead is not detected below the speed of 24 km/h (15 MPH).
4. When the selector lever is not in the “D” position or manual mode.
5. When the parking brakes are applied.
6. When the system judges the vehicle is at standstill.
7. When the front wiper s are operating at HI.
(If the vehicle is equipped with a rain sensing auto-wi per, the system may cancel when the wipers are set
to AUTO.)
8. When the SNOW mode switch is turned ON.
9. When 4WD shift switch is not AUTO position
10. When ABS or VDC (including the TCS) operates.
11. When the MAIN switch is turned OFF.
12. When a wheel slips.
13. When driving into a strong light (i.e., sunlight).
14. When the VDC is turned OFF.
15. When the system malfunction occurs.
CONVENTIONAL (FIXED SPEED) CR UISE CONTROL MODE FUNCTION
CONVENTIONAL (FIXED SPEED) CRUISE CONTROL MODE FUNCTION : System
JPOIA0223ZZ
Revision: 2010 May2011 QX56

CCS-20
< SYSTEM DESCRIPTION >[ICC]
SYSTEM
In the conventional (fixed speed) cruise control mode,
a warning chime does not sound to warn driver if own
vehicle are too close to the vehicle ahead, as neither the presence of the vehicle ahead nor the vehicle-to-
vehicle distance is detected.
OPERATION DESCRIPTION
To turn ON the conventional (fixed speed) cruise cont rol mode, push and hold the MAIN switch for longer than
approximately 1.5 seconds when ICC system is OFF.
When pushing the MAIN switch ON, the ICC system display and the MAIN switch indicator are displayed on
the information display.
After hold the MAIN switch ON for longer than approxim ately 1.5 seconds, the ICC system display goes out.
The MAIN switch indicator stays lit and brings the system to standby state.
NOTE:
 To turn on the vehicle-to-vehicle distance control mode again, turn OFF the system and quickly push (less
than 1.5 seconds) the MAIN switch.
 When the DCA system is ON, the conventional (fixed speed) cruise control mode cannot be turned on even
though the MAIN switch is pushed and held.
 To turn ON the conventional (fixed speed) cruise control mode, turn OFF the DCA system. Refer to DAS-68,
"System Description".
ADAS control unit performs the control as per the following:
Set Condition
When the system is under a standby state and the vehi cle speed is between approximately 40 km/h (25 MPH)
and 144 km/h (90 MPH), pushing the SET/COAST switch will start system control.
If the system is canceled by conditions 1-6 below, the sy stem will resume control at the last set cruising speed
by pushing the RESUME/ACCELERATE switch.
Cancel conditions1. When CANCEL switch is pressed.
2. When brake pedal depressed.
3. When the vehicle speed falls below approximately 32 km/h (20 MPH).
4. When the vehicle slows down more than 13 km/h (8 MPH) below the set speed.
5. When the selector lever is not in the “D” position or manual mode.
6. When the parking brakes are applied.
7. When the MAIN switch is turned OFF.
8. When VDC (including the TCS) operates.
9. When a wheel slips.
10. When the system malfunction occurs.
Constant
speed Comparing the set vehicle speed with the current vehicle speed, transmits the command to ECM via CAN communication
to reach the set vehicle speed, and controls the electronic throttle control actuator.
Revision: 2010 May2011 QX56

CCS-24
< SYSTEM DESCRIPTION >[ICC]
OPERATION
WARNING LAMP AND AUTOMATIC CANCELLATION DISPLAY
NOTE:
Condition Display on ICC system display
When own vehicle comes closer to the vehicle ahead and it is judged that the distance be-
tween the vehicles is not sufficient
JSOIA0301ZZ
Condition Description Display on ICC system display
Warning
display  When the VDC is turned OFF
 When the VDC or ABS (in-
cluding the TCS) operates
 When a wheel slips
 When the 4WD shift switch is not AUTO
 When the SNOW mode switch is turned ON
 When driving into a strong light (i.e., sunlight) A chime sounds and the control is automatically
canceled.
NOTE:
When the conditions listed above are no longer
present, turn the system OFF using the MAIN
switch.
Turn the ICC system back on to use the system.
When the sensor window is
dirty, making it impossible to de-
tect a vehicle ahead. A chime sounds and the control is automatically
canceled.
NOTE:
Park the vehicle in a safe place, turn the engine
OFF.
Clean the sensor window with a soft cloth and
then perform the settings again.
When the ICC system is mal-
functioning A chime sounds and the control is automatically
canceled.
NOTE:
Turn the engine OFF and restart engine. If there
is no malfunction, it is possible to set the system.
Automatic
cancella-
tion display  When brake pedal is de-
pressed
 When CANCEL switch is pressed
 When a vehicle ahead is not
detected below the speed of
24 km/h (15 MPH)
 When the system judges the
vehicle is at standstill
 When the selector lever is not in “D” position or manual
mode
 When the front wipers are op- erating at HI
(If the vehicle is equipped
with a rain sensing auto-wip-
er, the system may cancel
when the wipers are set to
AUTO)
 When the parking brake are
applied A chime sounds and the control is automatically
canceled.
NOTE:
 The system will be in a standby, after the control
is automatically canceled.
 A chime sounds when the control is automati-
cally canceled, except when brake pedal is de-
pressed or when CANCEL switch is pressed.
JSOIA0302ZZ
JSOIA0303ZZ
JSOIA0304ZZ
JSOIA0292ZZ
Revision: 2010 May2011 QX56

CCS-26
< SYSTEM DESCRIPTION >[ICC]
OPERATION
WARNING AND AUTOMATIC CANCELLATION DISPLAY
NOTE:
When the ICC system is automatica
lly canceled, the cancellation condition can be displayed on “WORK SUP-
PORT” of CONSULT-III (ICC/ADAS).
Condition Display on ICC system display
Standby mode
Control mode
JSOIA0307ZZ
JSOIA0308ZZ
Condition Description Display on ICC system display
Warning display When the ICC system is malfunc-
tioning A chime sounds and the control is
automatically canceled.
NOTE:
Turn the engine OFF and restart
engine. If there is no malfunction,
it is possible to set the system
System cancel
display  When brake pedal is depressed
 When pressing CANCEL switch
 When the vehicle speed falls be-
low approximately 32 km/h (20
MPH)
 When the vehicle slows down
more than 13 km/h (8 MPH) be-
low the set speed
 When the selector lever is not in
the “D” position or manual mode
 When the parking brakes are ap- plied
 When VDC (including the TCS) operates
 When a wheel slips A chime sounds and the control is
automatically canceled
NOTE:
 The system will be in a standby,
after the control is automatically
canceled
 A chime sounds when the con-
trol is automatically canceled,
except when brake pedal is de-
pressed or when CANCEL
switch is pressed
JSOIA0304ZZ
JSOIA0307ZZ
Revision: 2010 May2011 QX56