wheel INFINITI QX56 2011 Factory Owner's Guide

BRC-14
< SYSTEM DESCRIPTION >[WITH VDC]
COMPONENT PARTS
ABS Actuator and Electric Unit (Control Unit)
INFOID:0000000006222561
Electric unit (control unit) is in tegrated with actuator and motor/accumulator assembly and comprehensively
controls VDC function, TCS function, AB S function, EBD function, hill start assist function or brake limited slip
differential function.
ELECTRIC UNIT (CONTROL UNIT)
 Brake fluid pressure, engine and transmission are controlled according to signals from each sensor.
 If malfunction is detected, the system enters fail-safe mode.
ACTUATOR
The following components are integrated with ABS actuator.
Motor/accumulator Assembly
Pump Operates the pump drive according to signals from ABS actuator and electric unit (control unit) by the motor.
Motor Operates the motor drive according to signals fr om ABS actuator and electric unit (control unit).
Accumulator
 The accumulator accumulates brake fluid conveyed by the motor and pump.
Motor Relay
Operates the motor ON/OFF according to signals fr om ABS actuator and electric unit (control unit).
Actuator Relay (Main Relay)
Operates each valve ON/OFF according to signals fr om ABS actuator and electric unit (control unit).
ABS IN Valve and ABS OUT Valve
Increases, holds or decreases the fluid pressure of each caliper according to signals from ABS actuator and
electric unit (control unit).
Cut Valve 1, Cut Valve 2
Shuts off the ordinary brake line from master cylinder to signals from ABS actuator and electric unit (control
unit).
Suction Valve 1
Suction Valve 1 switches the brake path to convey accu mulator pressure to the front system, according to a
signal transmitted from the ABS actuat or and electric unit (control unit).
Suction Valve 2
Suction valve 2 releases accumulator pressure, accord ing to a signal transmitted from the ABS actuator and
electric unit (control unit).
Control Pressure Sensor (models with Advanced Driver Assistance System)
Detects the brake fluid pressure of brake caliper side and transmits a signal to ABS actuator and electric unit
(control unit).
Accumulator Pressure Sensor
The accumulator pressure sensor detects brake fluid pressure accumulated in the accumulator and conveys
the detected result to the ABS act uator and electric unit (control unit).
Master cylinder Pressure Sensor
Detects the brake fluid pressure of master cylinder part and transmits a signal to ABS actuator and electric unit
(control unit).
Wheel Sensor and Sensor RotorINFOID:0000000006222562
NOTE:
 Wheel sensor and sensor rotor is integrated in wheel hub assembly.
 Never measure resistance and voltage value using a tester because sensor is active sensor.
Revision: 2010 May2011 QX56

COMPONENT PARTSBRC-15
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
 Downsize and weight reduction is aimed. IC for detection portion and magnet for sensor rotor are adopted.
 Power supply is supplied to detection portion so that magnetic field
line is read. Magnetic field that is detected is converted to current
signal.
 When sensor rotor rotates, magnetic field changes. Magnetic field
change is converted to current signals (rectangular wave) and is
transmitted to ABS actuator and electric unit (control unit). Change
of magnetic field is pr oportional to wheel speed.
Stop Lamp SwitchINFOID:0000000006222563
Detects the operation status of brake pedal and transmits converted electric signal to ABS actuator and elec-
tric unit (control unit).
Steering Angle SensorINFOID:0000000006222564
Detects the following information and transmits steering angle signal to ABS actuator and electric unit (control
unit) via CAN communication.
 Steering wheel rotation amount
 Steering wheel rotation angular velocity
 Steering wheel rotation direction
Yaw Rate/Side/Decel G sensorINFOID:0000000006222565
Calculates the following information that affects the v ehicle and transmits a signal to ABS actuator and electric
unit (control unit) via communication lines.
 Vehicle rotation angular velocity (yaw rate signal)
 Vehicle lateral acceleration (side G signal) / longitudinal acceleration (decel G signal)
Brake Fluid Level SwitchINFOID:0000000006222566
Detects the brake fluid level in reservoir tank and trans mits converted electric signal from ABS actuator and
electric unit (control unit), when brake fluid level is the specified level or less.
Parking Brake SwitchINFOID:0000000006222567
Detects the operation status of parking brake switch and transmits converted electric signal from combination
meter to ABS actuator and electric unit (control unit).
VDC OFF SwitchINFOID:0000000006222568
 VDC OFF switch is integrated in SNOW MODE / TOW MODE / VDC OFF switch assembly (2WD models) or
4WD switch assembly (4WD models).
 The operation of the VDC OFF switch enables the arbi trary switching of the VDC function between stop sta-
tus and standby status. The status of the function is indicated by the VDC OFF indicator lamp. (ON: Non-
operational status, OFF: Standby status)
- VDC function NOTE:
Brake limited slip differentia l (BLSD) control operates.
- TCS function
 VDC OFF indicator lamp turns OFF (standby status) when the engine is started again after it is stopped once while VDC OFF indicator lamp is ON (non-operational status).
JPFIC0131GB
Revision: 2010 May2011 QX56

SYSTEMBRC-21
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
 Being returned to reservoir tank through ABS OUT valve, fluid pressure of rear LH caliper is decreased.
VDC is Operation (When Pressure Increases)
NOTE:
Control pressure sensor is applied to models with Advanced Driver Assistance System.
Example: When other than rear LH wheel is operation in the figure.
Front RH caliper Pressurized brake fluid from accumulator is supplied to front RH caliper through suction valve 2, suction
valve 1 and ABS IN valve. When not increases, ABS IN valve is closed and brakes fluid is not supplied to
front RH caliper.
Front LH caliper
 Pressurized brake fluid from accumulator is supplied to front LH caliper through suction valve 2, suction
valve 1 and ABS IN valve. When not increases, ABS IN valve is closed and brakes fluid is not supplied to
front LH caliper.
Rear RH caliper
Name Not activated When Pressure Increases
Cut valve 1 Power supply is not supplied (open) Power supply is supplied (close)
Cut valve 2 Power supply is not supplied (open) Power supply is supplied (close)
Suction valve 1 Power supply is not supplied (close) Power supply is supplied (open)
Suction valve 2 Power supply is not supplied (close) Power supply is supplied (open)
ABS IN valve Power supply is not supplied (open) Only wheel that the pressure is to be in-
creased: Power supply is not supplied (open)
Wheel other than the one that the pressure
is to be increased: Power supply is supplied (close)
ABS OUT valve Power supp ly is not supplied (close) Power supply is not supplied (close)
Each caliper (fluid pressure) — Pressure increases (only wheel that the
pressure is to be increased)
JPFIC0154GB
Revision: 2010 May2011 QX56

BRC-22
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
 Pressurized brake fluid from accumulator is supplied to rear RH caliper through suction valve 2 and ABS IN
valve. When not increases, ABS IN valve is closed and brakes fluid is not supplied to rear RH caliper.
Rear LH caliper Pressurized brake fluid from accumulator is supplied to rear LH caliper through suction valve 2 and ABS IN
valve. When not increases, ABS IN va lve is closed and brakes fluid is not supplied to rear LH caliper.
VDC is Operation (When Pressure Holds)
NOTE:
Control pressure sensor is applied to m odels with Advanced Driver Assistance System.
Example: When other than front LH wheel is operation in the figure.
Front RH caliper ABS IN valve is close, fluid pressure of front RH caliper is holds.
Front LH caliper
 ABS IN valve is close, fluid pressure of front LH caliper is holds.
Rear RH caliper
 ABS IN valve is close, fluid pressure of rear RH caliper is holds.
Name Not activated When Pressure holds
Cut valve 1 Power supply is not supplied (open) Power supply is supplied (close)
Cut valve 2 Power supply is not supplied (open) Power supply is supplied (close)
Suction valve 1 Power supply is not supplied (close) Power supply is supplied (open)
Suction valve 2 Power supply is not supplied (close) Power supply is supplied (open)
ABS IN valve Power supply is not supplied (open) Only wheel that the pressure is to be holds:
Power supply is supplied (close)
Wheel other than the one that the pressure
is to be holds: Power supply is not supplied (open)
ABS OUT valve Power supply is not supplied (close) Power supply is not supplied (close)
Each caliper (f luid pressure) — Pressure holds (only wheel that the pres-
sure is to be holds)
JPFIC0180GB
Revision: 2010 May2011 QX56

SYSTEMBRC-23
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Rear LH caliper ABS IN valve is close, fluid pressure of rear LH caliper is holds.
VDC is Operation (When Pressure Decreases)
NOTE:
Control pressure sensor is applied to model s with Advanced Driver Assistance System.
Example: When other than front LH wheel is operation in the figure.
Front RH caliper Being returned to reservoir tank through ABS OUT valv e, fluid pressure of front RH caliper is decreased.
Front LH caliper
 Being returned to reservoir tank through ABS OUT valve, fluid pressure of front LH caliper is decreased.
Rear RH caliper
 Being returned to reservoir tank through ABS OUT valve, fluid pressure of rear RH caliper is decreased.
Name Not activated When pressure decreases
Cut valve 1 Power supply is not supplied (open) Power supply is supplied (close)
Cut valve 2 Power supply is not supplied (open) Power supply is supplied (close)
Suction valve 1 Power supply is not supplied (close) Power supply is supplied (open)
Suction valve 2 Power supply is not supplied (close) Power supply is supplied (open)
ABS IN valve Power supply is not supplied (open) Only wheel that the pressure is to be de-
creases: Power supply is supplied (close)
Wheel other than the one that the pressure
is to be decreases: Power supply is not supplied (open)
ABS OUT valve Power supply is not supplied (close) Only wheel that the pressure is to be de-
creases: Power supply is supplied (open)
Wheel other than the one that the pressure is to be decreases: Power supply is not supplied (close)
Each caliper (fluid pressure) — Pressure decreases (only wheel that the
pressure is to be decreases)
JPFIC0181GB
Revision: 2010 May2011 QX56

BRC-26
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
ABS FUNCTION
ABS warning lamp and VDC warning lamp in combinati
on meter turn ON when a malfunction occurs in system
[ABS actuator and electric unit (control unit)]. The c ontrol is suspended for VDC function, TCS function, ABS
function, hill start assist function and brake limited sl ip differential (BLSD) function. The vehicle status
becomes the same as models without VDC function, TCS f unction, ABS function, hill start assist function and
brake limited slip differential (BLSD) function. However, EBD function is operated normally.
NOTE:
ABS self-diagnosis sound may be heard the same as in the normal condition, because self-diagnosis is per-
formed when ignition switch turns ON and when vehicle initially starts.
EBD FUNCTION
ABS warning lamp, brake warning lamp and VDC warning lamp in combination meter turn ON when a mal-
function occurs in system [ABS actuator and electric unit (control unit)]. The control is suspended for VDC
function, TCS function, ABS function, EBD function, hill start assist function and brake limited slip differential
(BLSD) function. The vehicle status becomes the sa me as models without VDC function, TCS function, ABS
function, EBD function, hill star t assist function and brake limited slip differential (BLSD) function.
DTC Malfunction detected condition Fail-safe condition
C1101 When an open circuit is detected in rear RH wheel sensor circuit.
The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function (only when both 2 rear wheels are malfunctioning)
 hill start assist function
 Brake limited slip differential
(BLSD) function
C1102 When an open circuit is detected in rear LH wheel sensor circuit.
C1103 When an open circuit is detected in front RH wheel sensor circuit.
C1104 When an open circuit is detected in front LH wheel sensor circuit.
C1105
 When power supply voltage of rear RH wheel sensor is low.
 When distance between rear RH wheel sensor and rear RH wheel sensor rotor is
large.
 When installation of rear RH wheel sensor or rear RH wheel sensor rotor is not
normal.
C1106  When power supply voltage of rear LH wheel sensor is low.
 When distance between rear LH wheel sensor and rear LH wheel sensor rotor is
large.
 When installation of rear LH wheel sensor or rear LH wheel sensor rotor is not nor- mal.
C1107  When power supply voltage of front RH wheel sensor is low.
 When distance between front RH wheel sensor and front RH wheel sensor rotor
is large.
 When installation of front RH wheel sensor or front RH wheel sensor rotor is not normal.
C1108  When power supply voltage of front LH wheel sensor is low.
 When distance between front LH wheel sensor and front LH wheel sensor rotor is
large.
 When installation of front LH wheel sensor or front LH wheel sensor rotor is not normal.
C1109  When ignition voltage is 10 V or less.
 When ignition voltage is 16 V or more. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C 1111
 When a malfunction is detected in motor or motor relay.
 When a low pressure malfunction is detected in accumulator.
 When a malfunction is detected in accumulator pressure sensor.
C 111 5 When difference in wheel speed between any wheel and others is detected during
the vehicle is driven, because of installation of other tires than specified. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
C 111 6
 When stop lamp switch signal is not input when brake pedal depress.
 When stop lamp switch signal is not input when stop lamp relay operates.
C 111 8
*1When a malfunction is detected in transfer control unit system.
Revision: 2010 May2011 QX56

SYSTEMBRC-29
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
side/decel G- sensor and wheel sensor, vehicle drivi ng conditions (conditions of understeer or oversteer) are
judged and vehicle stability is improved by brake forc e control on all 4 wheels and engine output control.
 Control unit portion automatically improves driving st ability by performing brake force control as well as
engine output control, by transmitting drive signal to actuator portion according to difference between target
side slip amount and vehicle side slip amount
 VDC function can be switched to non-operational status (OFF) by operating VDC OFF switch. In this case,
VDC OFF indicator lamp turns ON.
 VDC function is not operate when 4WD mode is “4L”. (Models with 4WD system)
 VDC warning lamp blinking while VDC function is in oper ation and indicates to the driver that the function is
in operation.
 Slight vibrations are felt on the brake pedal and t he operation noises occur, when VDC function operates.
This is not a malfunction because it is caus ed by VDC function that is normally operated.
 CONSULT-III can be used to diagnose the system diagnosis.
 Fail-safe function is adopted. When a malfunction occurs in VDC function, the control is suspended for VDC
function, TCS function, hill start as sist function and brake limited slip di fferential (BLSD) function. The vehi-
cle status becomes the same as m odels without VDC function, TCS functi on, hill start assist function and
brake limited slip differential (BLSD) function. Ho wever, ABS function and EBD function are operated nor-
mally. Refer to BRC-25, "
Fail-safe".
NOTE:
VDC has the characteristic as de scribed here, but it is not the device that helps reckless driving.
SYSTEM DIAGRAM
NOTE:
Transfer control unit is applied to models with 4WD system.
INPUT SIGNAL AND OUTPUT SIGNAL
JPFIC0133GB
JPFIC0183GB
Revision: 2010 May2011 QX56

BRC-30
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
Major signal transmission between each unit via communication lines is shown in the following table.
*1: Communication line between yaw rate/side/decal G s
ensor and ABS actuator and electric unit (control unit)
*2: Models with 4WD system
OPERATION CHARACTERISTICS
VDC Function That Prevents Oversteer Tendency
 During a cornering, brake force (brake fluid pressure) is applied on front wheel and rear wheel on the outer side of turn. Moment directing towards the outer side of turn is generated. Oversteer is prevented.
 Changing driving lane on a slippery road, when oversteer tendency is judged large, engine output is con- trolled as well as brake force (brake fluid pr essure) of 4 wheels. Oversteer tendency decreases.
VDC Function That Prevents Understeer Tendency
Component Signal description
Yaw rate/side/decel G sensor Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via com-
munication line
*1.
 Yaw rate signal
 Side G sensor signal
 Decel G sensor signal
ECM Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Accelerator pedal position signal
 Engine speed signal
Mainly receives the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
 Target throttle position signal
TCM Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Shift position signal
Transfer control unit
*2Mainly transmits the following si gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Current 4WD mode signal
Steering angle sensor Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Steering angle sensor signal
Combination meter Mainly receives
the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
 VDC warning lamp signal
 VDC OFF indicator lamp
JPFIC0135GB
JPFIC0136GB
Revision: 2010 May2011 QX56

SYSTEMBRC-31
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
 During a cornering, brake force (brake fluid pressu re) is applied on front wheel and rear wheel on the inner
side of turn. Moment directing towards the inner side of turn is generated. Understeer is prevented.
 Applying braking during a cornering on a slippery road, when understeer tendency is judged large, engine
output is controlled as well as brake force (brake fluid pressure) of four wheels. Understeer tendency
decreases.
TCS FUNCTION
TCS FUNCTION : System DescriptionINFOID:0000000006222573
 Wheel spin status of drive wheel is detected by wheel sensor of 4
wheels. Engine output and transmission shift status is controlled
so that slip rate of drive wheels is in appropriate level. When wheel
spin occurs on drive wheel, ABS ac tuator and electric unit (control
unit) perform brake force control of LH and RH drive wheels (apply
brake force by increasing brake fluid pressure of drive wheel) and
decrease engine torque by engine torque control. Wheel spin
amount decreases. Engine torque is controlled to appropriate
level.
 TCS function can be switched to non-operational status (OFF) by
operating VDC OFF switch. In this case, VDC OFF indicator lamp
turns ON.
 TCS function is not operate when 4WD mode is “4L”. (Models with
4WD system)
 VDC warning lamp blinking while TCS function is in operation and indicates to the driver that the function is in operation.
 Slight vibrations are felt on the brake pedal and the operation noises occur, when TCS function operates. This is not a malfunc-
tion because it is caused by TCS function that is normally oper-
ated.
 CONSULT-III can be used to diagnose the system diagnosis.
 Fail-safe function is adopted. W hen a malfunction occurs in TCS
function, the control is suspended for VDC function, TCS function,
hill start assist function and brake limited slip differential (BLSD)
function. The vehicle status becomes the same as models without VDC function, TCS function, hill start
assist function and brake limited slip differential (B LSD) function. However, ABS function and EBD function
are operated normally. Refer to BRC-25, "
Fail-safe".
SYSTEM DIAGRAM
NOTE:
JPFIC0137GB
JPFIC0138GB
JPFIC0139GB
Revision: 2010 May2011 QX56

SYSTEMBRC-33
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
ABS FUNCTION : System DescriptionINFOID:0000000006222574
 By preventing wheel lock through brake force (brake flui d pressure) control that is electronically controlled by
detecting wheel speed during braking, stability during em ergency braking is improved so that obstacles can
be easily bypassed by steering operation.
 During braking, control units calculates wheel speed and pseudo-vehicle speed, and transmits pressure
increase, hold or decrease signals to actuator portion according to wheel slip status.
 The following effects are obtained by preventing wheel lock during
braking.
- Vehicle tail slip is prevented during braking when driving straight.
- Understeer and oversteer tendencie s are moderated during brak-
ing driving on a corner.
- Obstacles may be easily bypassed by steering operation during braking.
 Slight vibrations are felt on the brake pedal and the operation noises occur, when ABS function oper ates. This is not a malfunc-
tion because it is caused by ABS function that is normally oper-
ated.
 CONSULT-III can be used to diagnose the system diagnosis.
 Fail-safe function is adopted. When a malfunction occurs in ABS function, the control is suspended for VDC function, TCS function,
hill start assist function and brake limited slip differential (BLSD)
function. The vehicle status becomes the same as models without
VDC function, TCS function, ABS func tion, hill start assist function
and brake limited slip differential (BLSD) function. However, EBD
function is operated normally. Refer to BRC-25, "
Fail-safe".
NOTE:
 ABS has the characteristic as described here, but it is not the device that helps reckless driving.
 To stop vehicle efficiently, ABS does not operate and ordinary brake operates at low speed [approx. 5 to 10 km/h (3.1 to 6.2
MPH) or less, but differs subject to road conditions).
 Self-diagnosis is performed immediately after when engine starts and when vehicle initially is driven [by vehi-
cle speed approx. 15 km/h (9.3 MPH)]. Motor sounds are generated during self-diagnosis. In addition, brake
pedal may be felt heavy when depressing brake pedal lightly. These symptoms are not malfunctions.
SYSTEM DIAGRAM
NOTE:
JPFIC0140GB
Revision: 2010 May2011 QX56