ISUZU AXIOM 2002 Service Repair Manual

SEATS8G±3
4. Pull out the reclining knob.
5. Remove the side cover.

Remove the two screws.
6. Remove the headrest.
7. Remove the reclining device.

Pull up on the seat back trim cover in order to
remove the reclining device fixing bolts.
750R200007
8. Remove the seat back assembly.

Remove the seat back assembly fixing nut on the
opposite side of the reclining device.
750R200008
9. Remove the trim cover (Seat back side).
10. Remove the guide holder.

Pull the guide holder out by holding the bottom end
of it from the seat back assembly.
11. Remove the seat adjuster.

Disconnect the release wire (4) and remove the
fixing bolts.
750RW006
12. Remove the seat belt buckle assembly.
13. Remove the trim cover (Seat cushion side).
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. Tighten the reclining device fixing bolts to the
specified torque.
Torque: 46 N´m (34 lb ft)
2. Tighten the front seat assembly fixing bolts to the
specified torque.
Torque: 39 N´m (29 lb ft)

8G±4SEATS
Power Seat Assembly
Power Seat Assembly and Associated Parts
750R200009
Legend
(1) Headrest
(2) Guide Holder
(3) Seat Back Frame Assembly
(4) Connecting Pipe
(5) Seat Back Pad
(6) Seat Heater (Required Option)
(7) Reclining Device Cover
(8) Reclining Device
(9) Outer Side Cover
(10) Reclining Switch Knob
(11) Slide Switch Knob
(12) Power Lumbar Switch (Driver's Side)
(13) Power Seat Switch
(14) Seat Cushion Frame Assembly(15) Power Seat Harness
(16) Adjuster Bracket Rear Cover
(17) Outer Seat Adjuster Assembly
(18) Adjuster Bracket Front Cover
(19) Front Cover
(20) Sliding Motor Cable
(21) Inner Seat Adjuster Assembly
(22) Seat Cushion Pad
(23) Seat Cushion Assembly/Seat Cushion Trim
Cover
(24) Seat Belt Buckle Assembly
(25) Inner Side Cover
(26) Power Lumbar Support Assembly (Driver's
Side)
(27) Seat Back Assembly/Seat Back Trim Cover

SEATS8G±5
Removal
1. Remove the adjuster bracket rear cover and the fixing
bolts on the rear side of the seat adjuster assembly.

Before removal, slide the power seat assembly
forward.
2. Remove the adjuster bracket front cover and the
fixing bolts on the front side of the seat adjuster
assembly.

Before removal, slide the power seat assembly
backward.
3. Disconnect the battery ground cable.
4. Remove the power seat assembly.

Disconnect the power seat harness connectors and
the seat belt warning connector of the driver side.
CAUTION: When raising power seat assembly (1),
use the handle (2) not the cable (3). A bent cable
causes noise to occur during power seat operation.

Please grip the handle (4).

Don't grip the cable (5).
750R200012
5. Pull the switch knobs out.
6. Remove the outer side cover.

Remove the two fixing screws and disconnect the
power seat switch connector.
7. Remove the power seat switch.

Remove the two fixing screws.
8. Remove the power lumber switch.

Remove the two fixing screws and connectors.
9. Remove the inner side cover.
10. Remove the headrest.
11. Remove the reclining device (2).

Flip up the seat back trim cover (1) in order to
remove the reclining device fixing bolts.

Disconnect the reclining motor harness connector
(3).
760R100037
12. Remove the reclining device covers.
13. Remove the trim cover and pad (Seat back side).
14. Remove the seat heater and connector (seat back
side).
15. Remove the power lumbar support assembly.
16. Remove the guide holder.

Pull the guide holder out by holding the bottom end
of it from the seat back assembly.
17. Remove the seat adjuster assembly.

Remove the four fixing bolts and disconnect the
sliding motor connector.
18. Remove the sliding motor cable (2).

Remove the nuts of each side.
CAUTION: Be sure to maintain the same position for
both outer and inner seat adjust assembly (1).
760R100038

8G±6SEATS
19. Remove the seat belt buckle assembly.
20. Remove the trim cover and pad (Seat cushion side)
21. Remove the seat heater and connector (Seat cushion
side).
22. Remove the power seat harness.
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. Tighten the reclining device fixing bolts to the
specified torque.
Torque: 46 N´m (34 lb ft)
2. Tighten the seat adjuster fixing bolts to the specified
torque.
Torque: 21 N´m (15 lb ft) to seat cushion
Torque: 39 N´m (29 lb ft) to body
3. Tighten the seat belt buckle assembly fixing bolts to
the specified torque.
Torque: 29 N´m (22 lb ft)

SEATS8G±7
Rear Seat Assembly
Rear Seat Cushion Assembly and Associated Parts
755RY00009
Legend
(1) Rear Seat Lock Striker
(2) Rear Seat Lock Assembly
(3) Rear Seat Belt Buckle Assembly(4) Seat Cushion Hinge
(5) Hinge Cover
(6) Seat Cushion Fixing Bolt
(7) Rear Seat Cushion Assembly

8G±8SEATS
Removal
1. Remove the hinge covers.
2. Remove the seat cushion fixing bolts.
3. Remove the seat cushion assembly (2).

Pull the strap (1) of the rear seat lock assembly to
release the seat lock.
755R100006
4. Remove the seat cushion hinges.
5. Remove the rear cushion trim cover (1) and rear seat
cushion pad (2).

Remove cushion trim cover from the rear cushion
frame (3) by prying on the plastic retainers (4).
755RX028
6. Remove the rear seat lock assembly and rear seat
belt buckle assembly.
7. Remove the rear seat lock strikers.

Remove the four bolts at each striker.
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. Tighten the rear seat lock assembly and rear seat belt
buckle assembly fixing bolts to the specified torque.
Torque: 39 N´m (29 lb ft)
2. Tighten the rear seat lock striker fixing bolts to the
specified torque.
Torque: 39 N´m (29 lb ft)
3. Tighten the seat cushion hinge fixing bolts to the
specified torque.
Torque: 39 N´m (29 lb ft)

SEATS8G±9
Rear Seat Back Assembly and Associated Parts
755R200005
Legend
(1) Headrest
(2) Seat Back Assembly
(3) Guide Holder
(4) Release Knob(5) Seat Lock Cover
(6) Seat Lock Striker
(7) Side Hinge
(8) Body Floor Panel
(9) Center Hinge
Removal
1. Pull the release knob and pull the seat back assembly
forward.
2. Remove the seat lock covers.

Remove the three screws from each side.
3. Remove the luggage floor carpets.

Pull the nine carpet fixing clips from the backside of
the seat back assembly.4. Remove the seat back assembly.

Remove the four fixing bolts at each seat back.
5. Remove the headrests.
6. Remove the release knobs.

Turn the knob counterclockwise to remove it.
7. Remove the trim covers.
8. Remove the guide holders.
9. Remove the side hinges.

Remove the one fixing nut at each side hinge.

8G±10SEATS
10. Remove the center hinge.

Remove the two fixing bolts.
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. Tighten the center hinge fixing bolts to the specified
torque.
Torque: 39 N´m (29 lb ft)
2. Tighten the side hinge fixing nuts to the specified
torque.
Torque: 29 N´m (22 lb ft)
3. Tighten the side lock striker fixing bolts to the
specified torque.
Torque: 19 N´m (14 lb ft)

SEATS8G±11
Main Data and Specifications
Torque Specifications
750R200010

8G±12SEATS
755R200009