display ISUZU KB P190 2007 Workshop User Guide
[x] Cancel search | Manufacturer: ISUZU, Model Year: 2007, Model line: KB P190, Model: ISUZU KB P190 2007Pages: 6020, PDF Size: 70.23 MB
Page 648 of 6020
BRAKE CONTROL SYSTEM 5A-55
Step Action Value(s) Yes No
7 Check the front left wheel speed sensor. Refer to
"W heel Speed Sensor Inspection procedure"
W as a problem found? - Go to Step 10 Go to Step 8
8 Does the sensor rotor have missing tooth or saw- toothed? - Go to Step 14 Go to Step 9
9 1. Clear the DTC.
2. Test run the vehicle, and check the DTC. Is the DTC displayed repeatedly? - Go to Step 18 Go to Step 17
10 Is the wheel speed sensor damaged or saw-toothed?
- Go to Step 15 Go to Step 16
11 Adjust the preload of the wheel bearing.
Is the action complete? - Verify repair -
12 Repair or replace the front left speed sensor or the
sensor rotor.
Is the action complete? - Verify repair -
13 Repair the front left speed sensor or the sensor rotor. Is the action complete? - Verify repair -
14 Replace the sensor rotor.
Is the action complete? - Verify repair -
15 Replace the front left wheel speed sensor.
Is the action complete? - Verify repair -
16 Repair or replace the front left speed sensor circuits.
Is the action complete? - Verify repair -
17 Check the connection btween the EHCU and the
front left wheel speed sensor and repair as
necessary Refer to "Note on Intermittents".
Is the action complete? - Verify repair -
18 Replace EHCU.
Note: Check the EHCU type for specification, when
the EHCU is replaced.
(Specification ; 2W D model or 4W D model)
Is the action complete? - Verify repair -
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 650 of 6020
BRAKE CONTROL SYSTEM 5A-57
Step Action
Value(s) Yes No
4 1. Replace rear right wheel speed sensor.
2. Select “Display DTCs” with the Tech 2. Note: Perform the various tests (actuator test, test
run, brake test, etc.) then observe the DTC with a
Tech 2.
Are any DTCs stored? - Go to Step 5 Verify repair
5 Replace EHCU.
Note: Check the EHCU type for specification, when
the EHCU is replaced.
(Specification ; 2W D model or 4W D model)
Is the action complete? - Verify repair -
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 652 of 6020
BRAKE CONTROL SYSTEM 5A-59
Step Action Value(s) Yes No
7 Check the rear right wheel speed sensor. Refer to
"W heel Speed Sensor Inspection procedure"
W as a problem found? - Go to Step 10 Go to Step 8
8 Does the sensor rotor have missing tooth or saw- toothed? - Go to Step 14 Go to Step 9
9 1. Clear the DTC.
2. Test run the vehicle, and check the DTC. Is the DTC displayed repeatedly? - Go to Step 18 Go to Step 17
10 Is the wheel speed sensor damaged or saw-toothed?
- Go to Step 15 Go to Step 16
11 Repair or replace the wheel bearing.
Is the action complete? - Verify repair -
12 Repair or replace the rear right speed sensor or the
sensor rotor.
Is the action complete? - Verify repair -
13 Repair the rear right speed sensor or the sensor rotor.
Is the action complete? - Verify repair -
14 Replace the sensor rotor. Is the action complete? - Verify repair -
15 Replace the rear right wheel speed sensor.
Is the action complete? - Verify repair -
16 Repair or replace the rear right speed sensor circuits.
Is the action complete? - Verify repair -
17 Check the connection btween the EHCU and the rear
right wheel speed sensor and repair as necessary
Refer to "Note on Intermittents".
Is the action complete? - Verify repair -
18 Replace EHCU.
Note: Check the EHCU type for specification, when
the EHCU is replaced.
(Specification ; 2W D model or 4W D model)
Is the action complete? - Verify repair -
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 654 of 6020
BRAKE CONTROL SYSTEM 5A-61
Step Action
Value(s) Yes No
4 1. Replace rear left wheel speed sensor.
2. Select “Display DTCs” with the Tech 2. Note: Perform the various tests (actuator test, test
run, brake test, etc.) then observe the DTC with a
Tech 2.
Are any DTCs stored? - Go to Step 5 Verify repair
5 Replace EHCU.
Note: Check the EHCU type for specification, when
the EHCU is replaced.
(Specification ; 2W D model or 4W D model)
Is the action complete? - Verify repair -
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 656 of 6020
BRAKE CONTROL SYSTEM 5A-63
Step Action Value(s) Yes No
8 Does the sensor rotor have missing tooth or saw-
toothed? - Go to Step 14 Go to Step 9
9 1. Clear the DTC.
2. Test run the vehicle, and check the DTC. Is the DTC displayed repeatedly? - Go to Step 18 Go to Step 17
10 Is the wheel speed sensor damaged or saw-toothed?
- Go to Step 15 Go to Step 16
11 Repair or replace the wheel bearing.
Is the action complete? - Verify repair -
12 Repair or replace the rear left speed sensor or the
sensor rotor.
Is the action complete? - Verify repair -
13 Repair the rear left speed sensor or the sensor rotor. Is the action complete? - Verify repair -
14 Replace the sensor rotor.
Is the action complete? - Verify repair -
15 Replace the rear left wheel speed sensor.
Is the action complete? - Verify repair -
16 Repair or replace the rear left speed sensor circuits.
Is the action complete? - Verify repair -
17 Check the connection btween the EHCU and the rear
left wheel speed sensor and repair as necessary
Refer to "Note on Intermittents".
Is the action complete? - Verify repair -
18 Replace EHCU.
Note: Check the EHCU type for specification, when
the EHCU is replaced.
(Specification ; 2W D model or 4W D model)
Is the action complete? - Verify repair -
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 657 of 6020
5A-64 BRAKE CONTROL SYSTEM
DTC C0238 (Flash Code 38) Front Speed Sensor Correlation
Step Action Value(s) Yes No
1 W ere the steps of the “Basic Diagnostic Flow Chart”
performed?
- Go to Step 2 Go to Basic
Diagnostic
Flow Chart
2 1. Check for the tire size of each wheels.
2. If the tire size is different, replace the tire.
3. If a problem is found, repair as necessary. W as a problem found? - Verify repair Go to Step 3
3 1. Check for the gear ratio of a front axle differential gear and a rear axle differential gear.
2. If the gear ratio is different, repair the gear ratio.
3. If a problem is found, repair as necessary. W as a problem found? - Verify repair Go to Step 4
4 Select “Display DTCs” with the Tech 2.
Note: Perform the various tests (actuator test, test
run, brake test, etc.) then observe the DTC with a
Tech 2.
Are any DTCs stored? - Go to Step 5 Verify repair
5 1. Check for a poor connection at the wheel speed sensor harness connector.
2. Check installation condition for wheel speed sensor.
3. If a problem is found, repair as necessary. W as a problem found? - Verify repair Go to Step 6
6 1. Check condition for sensor rotor.
2. If a problem is found, repair as necessary. W as a problem found? - Verify repair Go to Step 7
7 1. Ignition “OFF” disconnect the EHCU and wheel
speed sensor.
2. Check the circuit between EHCU and wheel speed sensor. (short ground, or short to voltage)
3. If a problem is found, repair as necessary. W as a problem found? - Verify repair Go to Step 8
8 1. Ignition “OFF”.
2. Check the EHCU circuit for an open, short to ground, or short to voltage. Also, check the EHCU
ignition feed circuit for an open or short to ground
and the EHCU ground circuit for an open or short to
voltage.
3. If a problem is found, repair as necessary. W as a problem found? - Verify repair Go to Step 9
9 1. Ignition “ON”, engine “OFF”.
2. Select “Display DTCs” with the Tech 2. Note: Perform the various tests (actuator test, test
run, brake test, etc.) then observe the DTC with a
Tech 2.
Are any DTCs stored? - Go to Step 10 Verify repair
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 660 of 6020
BRAKE CONTROL SYSTEM 5A-67
Step Action
Value(s) Yes No
3 1. Ignition “ON”, engine “OFF”.
2. Select “Display DTCs” with the Tech 2. Note: Perform the various tests (actuator test, test
run, brake test, etc.) then observe the DTC with a
Tech 2.
Are any DTCs stored? - Go to Step 4 Verify repair
4 Replace EHCU.
Note: Check the EHCU type for specification, when
the EHCU is replaced.
(Specification ; 2W D model or 4W D model)
Is the action complete? - Verify repair -
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 662 of 6020
BRAKE CONTROL SYSTEM 5A-69
Step Action
Value(s) Yes No
3 1. Ignition “ON”, engine “OFF”.
2. Select “Display DTCs” with the Tech 2. Note: Perform the various tests (actuator test, test
run, brake test, etc.) then observe the DTC with a
Tech 2.
Are any DTCs stored? - Go to Step 4 Verify repair
4 Replace EHCU.
Note: Check the EHCU type for specification, when
the EHCU is replaced.
(Specification ; 2W D model or 4W D model)
Is the action complete? - Verify repair -
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 664 of 6020
BRAKE CONTROL SYSTEM 5A-71
Step Action
Value(s) Yes No
3 1. Ignition “ON”, engine “OFF”.
2. Select “Display DTCs” with the Tech 2. Note: Perform the various tests (actuator test, test
run, brake test, etc.) then observe the DTC with a
Tech 2.
Are any DTCs stored? - Go to Step 4 Verify repair
4 Replace EHCU.
Note: Check the EHCU type for specification, when
the EHCU is replaced.
(Specification ; 2W D model or 4W D model)
Is the action complete? - Verify repair -
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
Page 666 of 6020
BRAKE CONTROL SYSTEM 5A-73
Step Action
Value(s) Yes No
3 1. Ignition “ON”, engine “OFF”.
2. Select “Display DTCs” with the Tech 2. Note: Perform the various tests (actuator test, test
run, brake test, etc.) then observe the DTC with a
Tech 2.
Are any DTCs stored? - Go to Step 4 Verify repair
4 Replace EHCU.
Note: Check the EHCU type for specification, when
the EHCU is replaced.
(Specification ; 2W D model or 4W D model)
Is the action complete? - Verify repair -
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007