torque ISUZU KB P190 2007 Workshop Repair Manual

ENGINE MECHANICAL (4JK1/4JJ1) 6A-47
Removal
1. Drain the engine coolant.
2. Remove the turbocharger. • Refer to “Turbocharger”.
3. Remove the EGR cooler heat protector.
4. Disconnect the water hoses from the EGR coole
r
water pipes.
5. Remove the EGR cooler.
6. Remove the exhaust manifold.







RTW 76ASH002101
Inspection
• Inspection of the exhaust manifold. Inspect the
plane surface of the plane on which the
manifold and the cylinder head are to be
installed.

Manifold installation plane surface mm (in)
Standard 0.3 (0.01) or lower
Limit 0.5 (0.02)

Caution:
If the plane surface exceeds the limit, replace it.




LNW 21BSH022301
• Check a crack in the exhaust manifold visually.
Carefully inspect the turbocharger for abrasion and/o
r
excessive wear. Make any necessary adjustments,
repairs, and/or part replacements.
Installation
1. Put the gasket in to install the exhaust manifold.
• Tighten up with the 8 nuts according to the
order given in the illustration.
Tightening torque: 52 N ⋅
⋅⋅
⋅
m (5.3 kg ⋅
⋅⋅
⋅
m / 38 lb ft)
Caution:
Do not tighten up too much because it hampers
expansion and contraction due to the heat from the
manifold.









RTW 76ASH002201


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6A-48 ENGINE MECHANICAL (4JK1/4JJ1)
2. Install the EGR cooler.
• Install the gaskets.
• Install the EGR cooler.
• Temporary tightening order.
1 →2→ 3→ 4→ 5→ 6
• Fully tightening order.
3 →4→ 5→ 1→ 2→ 6
Tighten the nut and bolts to the specified torque.
Tightening torque: Nuts and bots 1-5: 27 N·m (2.8 kg·m / 20 lb ft)
Bolt 6: 52 N·m (5.3 kg·m / 38 lb ft)


6
543
1
2

RTW 76FSH000201
3. Install the water hoses to the EGR cooler water
pipes.
4. Heat protector.
Tighten the bolts to the specified torque.
Tightening torque: 25 N·m (2.5 kg·m / 18 lb ft)




RTW 76FSH000101
5. Install the turbocharger.
• Refer to “Turbocharger”.
6. Replenish the engine coolant.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE MECHANICAL (4JK1/4JJ1) 6A-49
Torque Specifications



RTW 76AMF000701


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE MECHANICAL (4JK1/4JJ1) 6A-55
• If the measurement exceeds the limit, replace
either the idle gear or the shaft.
Clearance between the idle gear A and the shaft
mm (in)
Standard 0.020 − 0.062 (0.0007 − 0.0024)
Limit 0.200 (0.0079)

Clearance between the idle gear C and the shaft
mm (in)
Standard 0.025 − 0.075 (0.0010 − 0.0030)
Limit 0.200 (0.0079)


LNW 21BSH003601
Installation
1. Install the crankshaft gear.
2. Install the idle gear C. •
Apply engine oil over the part where the gear of
the idle gear shaft is to be put together.

•
Apply engine oil to the bolt screw thread and
seat, and temporarily tighten together with the
flange (tighten fully in later process).





RTW 56ASH011401
3. Install the idle gear A.
4. Tighten sub gear setting bolt. • Use the M6 bolts and lever to turn sub gear to
right direction until it aligns with the M6 bolt
hole between idle gear A and sub gear.
• Tighten the M6 bolt to a suitable torque to
prevent the sub gear from moving.






RTW 56ASH011501



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6A-56 ENGINE MECHANICAL (4JK1/4JJ1)
• Align the oil hole of the cylinder body (2) with
the oil hole of the idle gear A shaft (3).
• Install the flange so that the front mark (1) face
toward the front.
• Install the idle gear A and idle gear A flange,
idle gear A shaft at the position shown in the
figure.
•
Apply engine oil over the part where the gear of
the idle gear shaft is to be put together.
•
Apply engine oil to the bolt screw thread and
seat, and temporarily tighten together with the
flange (tighten fully in later process).




LNW 71BSH000501
• Attach, aligning with the gear crank: idle A and
timing mark.





RTW 56ALH000301
5. Tighten the bolts of idle gear A and idle gear C to
the specified torque.
Tightening torque: idle gear A 32 N ⋅
⋅⋅
⋅
m (3.3 kg ⋅
⋅⋅
⋅
m / 24 lb ft)
idle gear C 59 N ⋅
⋅⋅
⋅
m (6.0 kg ⋅
⋅⋅
⋅
m / 43 lb ft)





RTW 56ASH011701
Legend
1. Idle Gear A Bolt
2. Idle Gear C Bolt


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE MECHANICAL (4JK1/4JJ1) 6A-57
6. Remove the M6 bolt from the idle gear A.
7. Install the gear case cover. • Apply the liquid gasket (ThreeBond TB-1207B
or equivalent).


RTW 56ASH020101
Legend
1. Apply the liquid gasket

• Install the gasket in slot of the gear case cover.
• Tighten the bolts to the specified torque.
Tightening torque: 8 N ⋅
⋅⋅
⋅
m (0.8 kg ⋅
⋅⋅
⋅
m / 69 lb in)




RTW 56ASH012101
8. Install the vacuum pump.
Tightening torque: 25 N ⋅
⋅⋅
⋅
m (2.5 kg ⋅
⋅⋅
⋅
m / 18 lb ft)
• Install the oil pipe (feed side and return side) o
f
vacuum pump.
• Install the vacuum pipe bracket and vacuum
pipe.
9. Install the power steering pump. • Tighten the nuts to the specified torque.
Tightening torque: 25 N ⋅
⋅⋅
⋅
m (2.5 kg ⋅
⋅⋅
⋅
m / 18 lb ft)
• Connect the bracket (1) of power steering oil
hose.




LTW 56ASH000101

10. Install the crank pulley.
Tightening torque: 294 N ⋅
⋅⋅
⋅
m (30.0 kg ⋅
⋅⋅
⋅
m / 217 lb ft)
11. Install the A/C compressor drive belt and fan belt.
Refer to drive belt tension check procedure fo
r
Heating and air conditioning and Engine cooling in
this manual.
12. Install the cooling fan.
13. Install the fan guide.
14. Install the radiator upper hose.
15. Replenish the engine coolant.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6A-58 ENGINE MECHANICAL (4JK1/4JJ1)
Torque Specifications





LNW 76ALF000601


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6A-64 ENGINE MECHANICAL (4JK1/4JJ1)
3. Install the sub gear assembly.
• Clamp the camshaft in a vise. Insert soft metal
protectors (aluminum) between the vise
surfaces and the camshaft. Press against the
pin on the left side of the camshaft gear spring
(3) to make a gap on the right side of the
spring. Push the spring into place.
• Align the sub gear pin (2) with the hole in the
right side of the camshaft gear damper spring
(3). Press the sub-gear into place.






RTW 56ASH006701
Legend
1. Snap Ring
2. Sub-gear
3. Damper Spring
4. Camshaft Gear

• Use a pair of snap ring pliers to snuggly install
the snap ring.

4. Tighten sub gear setting bolt.
• Use 5-8840-2591-0 to turn sub gear to right
direction until it aligns with the M5 bolt hole
between camshaft driven gear and sub gear.
• Tighten the M5 bolt to a suitable torque to
prevent the sub-gear from moving.





RTW 56ASH006801

Installation
1. Check the crankshaft to make the No. 1 cylinder
meet the compression TDC.





RTW 76ASH001301
Legend
1. TDC




BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ENGINE MECHANICAL (4JK1/4JJ1) 6A-65
2. Install the camshaft assembly.
• Align timing mark on intake camshaft and
exhaust camshaft to idle gear D.




RTW 56ASH007001
Legend
1. Exhaust Camshaft Gear
2. Intake Camshaft Gear
3. Idle Gear D


3. Camshaft bearing caps, tighten ten bolts on one
side bank to the specified torque.
• Apply engine oil to camshaft journal and
bearing surface of camshaft bearing caps.






RTW 56ASH018401


4. Check that the alignment marks (camshaft bearing
cap and camshaft) are aligned.





RTW 56ASH006901
Legend
1.
Align mark on intake camshaft and exhaust
camshaft to mark of bearing cap

• Apply engine oil over the screw part and tighten
up the bearing cap with the prescribed torque.
Tightening torque: 18 N ⋅
⋅⋅
⋅
m (1.8kg ⋅
⋅⋅
⋅
m / 13 lb ft)
5. Remove the M5 lock bolt of fixing sub gear.
6. Adjustment of valve clearance. • Refer to installation procedure for inspection
/
adjustment of valve clearance in this manual.
7. Install the baffle plate. Tighten the bolts to the specified torque.
Tightening torque: 10 N ⋅
⋅⋅
⋅
m (1.0 kg ⋅
⋅⋅
⋅
m/87 lb in)
8. Install the cylinder head cover.
Refer to "Cylinder Head Cover".
9. Install the engine cover.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

6A-66 ENGINE MECHANICAL (4JK1/4JJ1)
Torque Specifications





RTW 56AMF001701


Special Tools
ILLUSTRATION PART NO.
PART NAME

5-8840-2591-0
Camshaft gear tool


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007