brake fluid ISUZU TFS SERIES 1997 User Guide

5-50 BRAKES
Return Port
Check the return port for obstructions and if necessary, clean
with a tag wire.
Blow away foreign matter with compressed air.
Primary Piston
After reassembly, push in the primary piston to see that returns
smoothly.
Repeat the test two or three times to see that brake fluid is
forced out from the front and rear outlets.

BRAKES 5-51
REASSEMBLY
; Repair Kit
Reassembly Steps
1. Cylinder assembly ; brake, master
2. Piston assembly ; secondary and spring
3. Piston assembly ; primary and spring
4. Ring ; snap
5. Gasket
6. Bolt ; stopper
7. Grommet
8. Reservoir ; fluid, brake
9. Screw
10. Seal
11. Cover ; fluid reservoir
12. Dust seal
Important Operations
1. Cylinder Assembly ; Brake, Master
Lubricate the master cylinder bore with clean rubber
grease.(arrowed portion)

5-54 BRAKES
Important Operation - Removal
3. Brake Line
When handling, be careful not to spill brake fluid over the
painted surfaces, as damage to the paint finish will result.
Important Operation - Installation
8. Master Cylinder Assembly
Check the distance from the flange face of the vacuum servo
to the end of the push rod before installation of the master
cylinder.
Projection (A) mm(in)
18.0 - 18.2 (0.709 - 0.717)
If the measured distance deviates from the specified range,
make an adjustment with the lock nut
1 at the end of the push
rod.
Torque N
m(kgfm/lbft)
15 - 25 (1.5 - 2.5 / 11 - 18)
7. Vacuum Servo to Dash Panel and Pedal Mounting
Bracket
Torque N
m(kgfm/lbft)
22 - 31 (2.2 - 3.2 / 16 - 23)
Apply sealer to the dashboard fitting face.
3. Brake Line
Torque N
m(kgfm/lbft)
9 - 15 (0.9 - 1.5 / 6.5 - 11)

BRAKES 5-67
TROUBLESHOOTING
Condition and Cause Correction
Poor Brake Action
Master cylinder faulty Correct or replace
Power cylinder faulty Correct or replace
Level of brake fluid in reservoir too low Replenish and bleed
Air in hydraulic circuit Bleed
Front disc brake caliper faulty Clean or replace
Rear brake wheel cylinder faulty Clean or replace
Water or oil on brake pads or linings Clean or replace
Brake pads or linings hardened Replace
Brake pads or linings in poor contact with rotor or brake drum Correct
Brake pads or linings worn Replace
Brake disc or drum rusted Grind or replace
Check valve in vacuum hose faulty Correct or replace
Brake Squeak
Brake pads or linings worn Replace
Brake pads or linings hardened Replace
Brake pads or linings in poor contact with rotor or brake drum Correct
Brake disc(s) warped, worn or damaged Grind or replace
Disc brake anti-squeak shims fatigued Replace
Front hub bearings loose or preload is incorrect Adjust or replace
Brake disc or drum rusted Grind or replace
Brake Pull
Tire inflation pressures unequal Adjust
Front wheel alignment incorrect Adjust
Water or oil on brake pads or linings Clean or replace
Brake pads or linings hardened Replace
Brake pads or linings worn excessively Replace
Brake drum or rotor worn or scored Grind or replace
Front or rear wheel cylinder or disc brake caliper malfunctioning Clean or replace
Front hub bearing preload incorrect Adjust or replace
Brake pad or lining clearances unequal Adjust or replace
Brake Drag
Parking brake maladjusted Adjust
Brake pad or lining clearance insufficient Adjust
Brake pedal free play insufficient Adjust brake pedal height or power cylinder operating rod
Piston in master cylinder sticking Clean or replace
Pistons in disc brake caliper sticking Replace piston seals
Pistons in rear brake wheel cylinders sticking Clean or replace
Brake pads sticking in caliper Clean
Return springs weakened Replace
Parking brake binding Overhaul rear brakes
Front hub bearing preload incorrect Adjust or replace
Rear brake shoes not returning Correct or replace brake back plate, check automatic adjuster and
replace as necessary
Obstructions in hydraulic circuit Clean
Rotor warped excessively Grind or replace
Rear brake drum distorted Grind or replace
Piston cups swollen Replace brake fluid and piston cups
Check valve ; vacuum hose faulty Replace
Parking cable sticking Clean or replace
Rear disc brake over adjust Adjust or overhaul rear brakes
Excessive Brake Pedal Travel
Air in hydraulic circuit Bleed hydraulic circuit
Level of brake fluid in reservoir too low Replenish brake fluid reservoir to specified level and bleed hydraulic
circuit as necessary.
Master cylinder push rod clearance excessive Adjust
Leakage in hydraulic system Correct or replace defective parts
Rear disc brake autoadjuster malfunction Overhaul rear brakes

7C-14 CLUTCH
Bleeding Procedure
1. Bleed air from clutch operating cylinder according to the
following procedure.
Carefully monitor fluid level at master cylinder during
bleeding operation.
1. Set the paking brake.
2. Top up reservoir with recommended brake fluid.
3. Connect a transparent vinyl tube to air bleeder valve.
4. Fully depress clutch pedal several times.
5. W ith clutch pedal depressed, open bleeder valve to release
air.
6. Close bleeder valve.
7. Repeat steps 5 through 6 above until brake fluid flows from
air bleeder valve without air bubbles.
8. Bleed air from clutch damper according to the above
procedure.
9. Repeat the above bleeding procedure 1 and 2 several
times.

7C-32 CLUTCH
REASSEMBLY
* Apply grease
(COSMO rubber grease)
Repair Kit
Reassembly Steps
1. Cylinder body
2. Piston and assembly
3. Push rod
4. Stopper
5. Stopper ring6. Dust cover
7. Lock nut
8. Joint
9. Oil tank assembly
10. Oil tank band
Important Operations
1. Cylinder Body
Immerse the cylinder body in clean brake fluid.

7C-34 CLUTCH
Inspection and Repair
Make the necessary adjustments, repair, and part
replacements if excessive wear or damage is
discovered during inspection.
Cylinder Body
1. Clean the cylinder body.
2. Check the fluid return port for restrictions and clean
it if necessary.
Inner Parts
1. Visually inspect the disassembled parts for
excessive wear and damage.
Replace the inner parts with new parts shown in the
illustration.
2. Measure the clearance between master cylinder
wall and piston.
If the measured value exceeds the specified limit,
the master cylinder assembly must be replaced.
Standard: 0.07 mm (0.0028 in)
Limit: 0.15 mm (0.0059 in)
Reassembly
To reassemble, follow the disassembly steps in the
reverse order, noting the following points:
Cylinder Body
Immerse the cylinder body in clean brake fluid.
Piston Assembly
Before installing, apply a thin coat of rubber grease to
the piston. Install cup in groove in piston with lip turned
to front of cylinder. Use care to prevent damaging the
lip of the piston seat.

CLUTCH 7C-35
SLAVE CYLINDER (Except 6VD1 Engine)
DISASSEMBLY
Disassembly Steps
1. Boot
2. Push rod
3. Piston and piston cup4. Spring
5. Cylinder body
6. Solenoid switch
Important Operations
1. Boot
Brake fluid spilled on painted or plastic surfaces will cause
serious damage.
Take care not to spill brake fluid.

CLUTCH 7C-37
REASSEMBLY
* Apply grease
(COSMO rubber grease)
Reassembly Steps
1. Cylinder body
2. Spring
3. Piston and piston cup4. Push rod
5. Boot
6. Solenoid switch
Important Operations
1. Cylinder Body
1) Clean the cylinder body.
2) Apply brake fluid to the cylinder bore.
3. Piston and piston Cup
1) Apply brake fluid to the piston and piston cup.
2) Install the cups to the piston.
Note the installation direction of the piston cups in the
illustration.
3) Install the piston and piston cup to the cylinder body.