battery JAGUAR X308 1998 2.G Owners Manual

Engine - Intake Manifold Gasket RH
In-vehicle Repair
1. Open the engine compartment and fit paintwork protection
sheets.

2. Disconnect the batt ery ground cable.
Remove the battery cover.

3. WARNING: BEFORE PROCEEDING, IT IS ESSENTIAL THAT THE WARNINGS GIVEN IN SECTION 100-00 (UNDER THE
HEADING 'SAFETY PRECAUTIONS') ARE READ AND
UNDERSTOOD.
Depressurise the fuel system.
Ensure that the ignition is switched off and remove the
valve cap from the fuel cross-over pipe. Place a cloth
under the valve to collect any spillage.
Place a closed container, su itable for collecting fuel,
adjacent to the vehicle. Remove the lid.

4. Connect the fuel injection pres sure test equipment 310 - 058
(or other suitable type). Insert the drain / bleed tube into the
fuel container. Follow the ma nufacturer's instructions and
depressurise the fuel system.
5. Store the drained fuel safely and ensure that the lid is closed
securely. Remove the equipmen t and discard the cloth from
beneath the valve. refit the valve cap.
6. Drain the radiator coolant. Refer to Operation 26.10.01.
7. Disconnect the breather pipe fro m the A-Bank camshaft cover.
1. Disconnect the breather pipe from the stub pipe.
2. Remove and discard the O-ring seal from the breather
pipe.

12. Reconnect the air cleaner cover.
Fit the five clips which secu re the air cleaner cover.

13. Connect the intake tube to the throttle body.
1. Connect the intake tube to the throttle body.
2. Fit the two bolts which secure the intake tube to the throttle body.
14. Reconnect the air flow meter multi-plug.
15. Fit a new strap to secure the vacuum pipe to the induction
elbow.

16. Connect the breather pipe to the A-Bank camshaft cover.
1. Fit a new O-ring seal to the breather pipe.
2. Reconnect the breather pipe to the stub pipe.
17. Refill the cooling system. Refer to Operation (SC) (26.10.01).
18. Connect the battery and fit the battery cover.

Refer to the Battery Reconnection Procedure (86.15.15).
19. Remove the paintwork protection sheets and close the engine
cover.

Engine - Oil Pump4.0L NA V8 - AJ27/3.2L NA V8 - AJ26
In-vehicle Repair
Removal
Installation

1. Disconnect battery ground cable.
Remove the battery cover.
2. Remove the engine compartment cover (bonnet) for improved
access to the fro nt of the engine. Refer to Operation 76.16.01.
3. Remove the Crankshaft Sprocket B-Bank. Refer to Operation
12.65.76.

4. Remove the oil pump.
1. Remove the four bolts which secure the oil pump to the cylinder block.
2. Remove the oil pump.
3. Remove the gasket.
5. Clean and inspect all compon ents and mating faces.
1. Fit the oil pump to the cylinder block.
1. Fit a new gasket to the block face.
2. Fit the oil pump onto the front of the crankshaft, to
the block face; ensure that the drive flats on the

inside of the pump gear engage correctly with the
mating flats on the crankshaft.
3. Fit the securing bolts and tighten to 11 - 13 Nm.
2. Refit both sprockets to the crankshaft, both primary timing
chains, the timing cover and al l associated components. Refer
to Operation 12.65.76.
3. Refit the engine compartment cover (bonnet). Refer to
Operation 76.16.01.
4. Refer to the Battery Reconnection Procedure 86.15.15.

Engine - Oil Pump4.0L SC V8 - AJ26
In-vehicle Repair
Removal
Installation

1. Disconnect battery ground cable.
Remove the battery cover.
2. Remove the engine compartment cover (bonnet) for improved
access to the fro nt of the engine. Refer to Operation 76.16.01
(SC).
3. Remove the Crankshaft Sprocket B-Bank. Refer to Operation
12.65.76 (SC).

4. Remove the oil pump.
1. Remove the four bolts which secure the oil pump to the cylinder block.
2. Remove the oil pump.
3. Remove the gasket.
5. Clean and inspect all compon ents and mating faces.
1. Fit the oil pump to the cylinder block.
1. Fit a new gasket to the block face.
2. Fit the oil pump onto the front of the crankshaft, to

the block face; ensure that the drive flats on the inside
of the pump gear engage correctly with the mating
flats on the crankshaft.
3. Fit the securing bolts and tighten to 11 - 13 Nm.
2. Refit both sprockets to the crankshaft, both primary timing
chains, the timing cover and al l associated components. Refer
to Operation 12.65.76 (SC).
3. Refit the engine compartment cover (bonnet). Refer to
Operation 76.16.01 (SC).
4. Refer to the Battery Reconnection Procedure 86.15.15.

Engine - Primary Timing Chain LH4.0L NA V8 - AJ27
In-vehicle Repair
Removal
Special Tool(s)

Camshaft setting
303 - 530

Timing chain tensioning
303 - 532

Wedges, primary chain
303 - 533

Crankshaft setting
303 - 531
1. Open the engine compartment and fit paintwork protection
sheets.
2. Set the engine compartment cover to the service access
position.

3. Disconnect the batt ery ground cable.
Remove the battery cover.
4. Remove the Timing Co ver. Refer to Operation 12.65.01 in this
Section.
5. Remove the VVT bush carrier from the A-Bank.
1. Remove the three bolts which secure the carrier to the cylinder block.

1. Fit the new sealing ring (scarf jointed) to the carrier bush groove.
2. Fit a new O-ring to the carrier oil-way.

22. NOTE: Lubricate the seal (s carf jointed) and the bush.
Fit the VVT bush carrier to the cylinder block.
1. Fit the bush carrier assembly.
1. Check that the seals are in place and that the ring dowels are engaged squa rely. Fully locate the
assembly as much as possible by hand pressure.
2. Fit the two securing bolts and one nut. Tighten to 19 - 23 Nm.
23. Refit the Timing Cover. Refer to Operation 12.65.01 in this
Section.
24. Move the engine compartment cover from the service position
and connect the gas struts.
25. Remove the paint protection sheets and close the cover.
26. Connect the battery and fit the battery cover.
Refer to the Battery Reconnection Procedure 86.15.15.

Engine - Primary Timing Chain LH4.0L SC V8 - AJ26/3.2L NA V8 - AJ26,
3.2L/4.0L
In-vehicle Repair
Removal
Special Tool(s)

Camshaft setting
303-530

Timing chain tensioning
303-532

Wedges, primary chain
303-533

Crankshaft setting
303-531
1. Open the engine compartment and fit paintwork protection
sheets.
2. Set the engine compartment cover to the service access
position.

3. Disconnect the batt ery ground cable.
Remove the battery cover.
4. Remove the Timing Cover. Re fer to Operation 12.65.01.
5. Raise the vehicle on a ramp.
6. Remove the crankshaft position sensor.
1. Remove the bolt which secures the crankshaft