parking brake JAGUAR X308 1998 2.G Owner's Manual

10
.
Install washer and nut on pivot pin, but DO NOT tighten nut.

11
.
Install hub on axle shaft .
Route parking brake cable throu
gh hub carrier aperture
and install grommet.
Appl
y Loctite 270 to axle shaft splines and thread, and
fully seat hub on shaft.

12
.
Install locating collar and hub nut on axle shaft, but DO NOT
tighten hub nut.
13. Tighten pivot pin nut.
Al
ign marker on pivot pin flange with mark made on
wishbone.
Ensuri
ng pin position is not
disturbed, tighten nut to 88-
118Nm.

20
.
Remove nuts and withdraw special tool (204-195) from hub.
21. Install rear wheel. Refer to Section 204-04.
22. Remove stands and lower vehi cle onto wheels. Refer to
section 100-02.
23. Raise vehicle on four-post lift.

24
.
Route parking brake cable through suspension mounting
bracket and secure with clip.

25
.
Route parking brake cable through equalizer (LH side cable
only).

26
.
Install parking brake cabl e in connecting clip.
27. Adjust parking brake cable. Refer to 70.35.10.
28. Lower four-post lift
29. Apply parking brake.
30. Carry out rear wheel alignm ent check and adjust as


necessary. Refer
t
o 204-02 Specification section.

Rear Su
spension - Wh
eel Knuckle Bushing
Remo
val and Installation
Remov
a
l
S
p
ecial Tool(s)

Hub Holdin
g Tool
2
04-195 (JD227)

Hub Pu
ller

204-011 (JD 1D)

D rive
r Handle
100-013 (18G-134)

Bearing Cu p Replacer Adaptor
2
04-120 (JD 550-6)
1. CAUTION: Replacement of nuts and bolts: Various
thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt
can be used. See section 100-00 for information.
Release parking brake.
2. Ra
ise the vehicle on a four-post lift.

3. Fully slacken bu
t do not remove parking brake cable adjuster
nut.
4. Release appropriate side parkin g brake cable from connecting

cli
p.

5. With
draw parking brake cable th
rough equalizer (LH side cable
only).
6. Lower four-post lift.
7. Raise rear of vehicle to workin g height and support on stands.
Refer to section 100-02.
8. Remove rear wheel. Refer to section 204-04.

9. Posit
ion special tool (204-1
95) on hub studs and install
securing nuts.

10
.
Slacken but do not remove hub to axle shaft securing nut.
11. Remove securing nuts from stud s and withdraw special tool
(204-195) from hub.
12. Remove rear brake disc. Refer to 70.10.13.
13. Remove parking brake shoe s. Refer to 70.40.05.
14. Remove wheel speed sensor.

19
.
Install a thread protector on axle shaft.

20
.
Release hub from axle shaft.
Position hu
b puller on hub studs. (204-011)
Inst

all securing nuts.
Progres

sively tighten
puller center bolt to release hub from
axle shaft splines.
21. Remove nuts and release puller from hub.
22. Remove thread protec tor from axle shaft.

23
.
Release handbrake cable from suspension mounting bracket.
Remove cable reta
ining clip.
Draw c

able through suspension mounting bracket
aperture.
24. Remove parking brake cable to hub carrier grommet.

25. Remove back plate.
Re
move four screws securing
back plate to hub carrier.
Withdraw back plate
complete
with parking brake cable.

26 . Remove h
ub and carrier.
With
draw pivot pin
.
R
e
move hub and carrier assemb
ly from wishbone and axle
shaft.

27 . R
emove shim from each end of pivot pin sleeve.
28. Withdraw pivot pin sleeve from hub carrier.

19
.
Install wheel speed sensor on hub carrier.
Posit
ion sensor on hub carrier
and install and tighten bolt
to 7-10Nm.
Conne
ct wheel speed sensor harness to sensor.

20
.
Using new tie strap, secure wh eel speed sensor harness to
brake hose clip.
21. Install parking brake shoe s. Refer to 70.40.05.

22
.
Install special tool (204-195) on studs and install securing
nuts.
23. Tighten hub nut to 304-336Nm.

24
. R
emove nuts and withdraw special tool (204-195) from hub
studs.
25. Install brake disc. Refer to operation 70.10.13.
26. Install rear wheel. Refer to section 204-04.
27. Remove stands and lower vehicl e. Refer to section 100-02.
28. Raise vehicle on four-post lift.

29 . Rout
e brake LH cable through equalizer.

30 . Inst
all cable in connecting clip.
31. Adjust parking brake cable. Refer to 70.35.10.
32. Lower four-post lift.
33. Apply parking brake.
34. Carry out rear wheel alignm ent check and adjust as
necessary. Refer to 204-02 Specification section.

Driveshaft -
Torques



Comp

onent
Nm
Bol
t
M12 - Jurid flexible coupling to
transmission and final drive flanges
75
-
88
Screw
-
Centre bearing to underbody
19
,5
- 26,5
Screw
-
Parking brake relay mounting bracket to underbody
19
,5
- 26,5_

Driveshaft - Driveshaft
Remo
val and Installation
Remov
a
l
CAUTI
O
N: To preserve 'drive line' refine
ment, individual parts, other than fixings, MUST NOT be renewed. In the event
of any balance or driveshaft component related problem, the complete assembly must be renewed. Under no circumstances
may the flexible (Jurid) coupling be remo ved from the driveshaft (or its fixings be loosened). Do not drop or subject the
driveshaft to damage.
1. Disc
onnect the battery ground
lead and raise the vehicle for
access
2. Remove the front exha ust muffler, 30.10.18

3. Re
move the driveshaft from
the transmission flange.
If required, 'match mark'

the transmissi on flang and
coupling
Unscrew the fi xings (3)

4. Relea s
e the parking brake relay
lever mounting bracket fixings
(4) and allow the assembly to hang down

5. Disc onne
ct the driveshaft fr
om the differential flange
5. CAUTION: Under no circumstances must the
flexible coupling (or its fixings) be loosened or removed
from the drive shaft
1. 'Match mark' the FLEX IBLE COUPLING to the
differential DRIVE FLANGE
2. Remove the fixings (3)
6. Re
move the driveshaft
6. CAUTION: Ensure that the driveshaft front and
rear sections do not become disengaged. Secure the front
and rear sections to preven t sliding joint disengagement
during transport